2008 SAAB 9-3 garage door opener

125 Interior equipment
Interior rearview mirrorThe interior rearview mirror is of the auto-
dimming type and can be deflected with the
lever on its underside. Certain variants have
an autodimming rearview mirror.
The lever should be in the normal position
when you adjust the mirror.
Interior rearview mirror with
garage opener, autodimming
function and compass3
33 3
Retain your original garage door opener
(transmitter) for future programming proce-
dures (i.e., new vehicle purchase). It is also
suggested that upon the sale of the vehicle,
the programmed garage opener buttons be
erased for security purposes, see
page 128.
WARNING
Make sure that people and objects are out
of the way of moving door or gate to pre-
vent potential harm or damage.
When programming the garage opener,
you may be operating a garage door or
gate operator. Therefore it is advised to
park outside of the garage.
Do not use the garage opener with any
garage door opener that lacks the safety
stop and reverse feature as required by
federal safety standards. (This includes
any garage door opener model manufac-
tured before April 1, 1982.). A garage
door opener which cannot detect an
object, signaling the door to stop and
reverse, does not meet current federal
safety standards. Using a garage door
opener without these features increases
risk of serious injury or death.
Mirror position lever1 Normal position
2 Antidazzle position
Buttons for garage opener, autodimming
and compass
1–3 Garage opener
4LED
5 Autodimming/compass ON/OFF
6 Compass bearing
93_US_M08.book Page 125 Friday, May 11, 2007 11:37 AM
ProCarManuals.com

126 Interior equipmentPreparations for first-time programming
Before programming the garage opener for
the first time, you must delete any factory
codes.
Press and hold the two outer buttons until
the indicator light begins to flash-after
20 seconds. Release both buttons. Do not
hold for longer that 30 seconds. The garage
opener is now in the train (or learning) mode
and can be programmed at any time begin-
ning with "Programming" - step 2.Programming
The garage opener can record and store the
frequencies of three different remote con-
trols.
The battery in the remote control should be
fairly new for programming to work well.
Do not repeat "Programming" - step two
to train additional devices to a second or
third button. Begin with "Programming" -
step three.
1 Turn the ignition ON.
2 Press and hold the two outer buttons
(buttons one and three) - releasing only
when the indicator light begins to flash
(after 20 seconds). Do not hold the
buttons for longer than 30 seconds and
do not repeat step two to program a
second and/or third hand-held transmit-
ter to the remaining two buttons.
3 Position the end of your hand-held trans-
mitter 1-3 inches (5-14 cm) away from
the button you wish to program while
keeping the indicator light in view. The
transmitter should face the mirror from
below or left side of the mirror.
4 Simultaneously press and hold both the
chosen and hand-held transmitter
buttons. Do not release the buttons
until step 5 has been completed.Note: Some gate operators and garage
door openers may require you to replace
this Programming Step 4 with procedures
noted in the "Gate Operator / Canadian
Programming" section.
5 After the indicator light changes from a
slow to a rapidly blinking light, release
both the mirror and hand-held transmit-
ter buttons.
6 Press and hold the just-trained button
and observe the indicator light.
If the indicator light stays on
constantly, programming is complete
and your device should activate when
the button is pressed and released.
Note: To program the remaining two but-
tons, begin with "Programming" - step
three. Do not repeat step two.93_US_M08.book Page 126 Friday, May 11, 2007 11:37 AM
ProCarManuals.com

127 Interior equipment
If the indicator light blinks rapidly for two
seconds and then turns to a constant
light continue with "Programming"
steps 7-9 to complete the programming of
a rolling code equipped device (most
commonly a garage door opener).
7 At the garage door opener receiver
(motor-head unit) in the garage, locate
the "learn" or "smart" button. This can
usually be found where the hanging
antenna wire is attached to the
motor-head unit.
8 Firmly press and release the "learn" or
"smart" button. (The name and color of
the button may vary by manufacturer.)
Note: There are 30 seconds in which to ini-
tiate step nine.
9 Return to the vehicle and firmly press,
hold for two seconds and release the
programmed button. Repeat the
"press/hold/release" sequence a
second time, and, depending on the
brand of the garage door opener (or
other rolling code equipped device),
repeat this sequence a third time to
complete the programming process.
The garage opener should now activate
your rolling code equipped device.
Note: To program the remaining two but-
tons, begin with "Programming" - step
three. Do not repeat step two. Gate Operator / Canadian Programming
Canadian radio-frequency laws require
transmitter signals to "time-out" (or quit)
after several seconds of transmission -
which may not be long enough for the
garage opener to pick up the signal during
programming. Similar to this Canadian law,
some U.S. gate operators are designed to
"time-out" in the same manner.
If you live in Canada or you are having diffi-
culties programming a gate operator by
using the "Programming" procedures
(regardless of where you live), replace
"Programming " step 4 with the following:
Note: If programming a garage door opener
or gate operator, it is advised to unplug the
device during the "cycling" process to pre-
vent possible overheating.
Continue to press and hold the button while
you press and release - every two sec-
onds ("cycle") your hand-held transmitter
until the frequency signal has successfully
been accepted by the garage opener. (The
indicator light will flash slowly and then rap-
idly.)
Proceed with "Programming" step five to
complete.Reprogramming a single button
To program a device to the garage opener
using a button previously trained, follow
these steps:
1 Press and hold the desired button. DO
NOT release the button.
2 The indicator light will begin to flash after
20 seconds. Without releasing the
button, proceed with "Programming" -
step 3.
NOTESwitch off the power supply to the garage
door or gate (or park the car beyond the
range of the remote control) while pro-
gramming using the "cycling" method to
prevent damaging the electrical motor.
93_US_M08.book Page 127 Friday, May 11, 2007 11:37 AM
ProCarManuals.com

128 Interior equipmentErasing the three buttons
To erase programming from the three but-
tons (individual buttons cannot be erased
but can be "reprogrammed" as outlined
below), follow the step noted:
Press and hold the two outer buttons until
the indicator light begins to flash-after
20 seconds. Release both buttons. Do
not hold for longer that 30 seconds. The
garage opener is now in the train (or
learning) mode and can be programmed
at any time beginning with "Programming"
- step 3.Opening a garage door
To operate, simply press and release the
programmed button. Activation will now
occur for the trained device (i.e. garage door
opener, gate operator, security system,
entry door lock, home/office lighting, etc.).
For convenience, the hand-held transmitter
of the device may also be used at any time.
AutodimmingPress button 5 briefly to switch autodimming
on or off. When autodimming is switched on,
a 1 is displayed briefly in the compass win-
dow. A 0 indicates that autodimming is
switched off.Buttons for garage opener, autodimming
and compass
1–3 Garage opener
4LED
5 Autodimming/compass ON/OFF
6 Compass bearing
93_US_M08.book Page 128 Friday, May 11, 2007 11:37 AM
ProCarManuals.com

304 IndexDeep water, driving through
_______ 196
Definitions and terminology, tire ____ 254
Determining correct load, tires
_____ 256
Direction indicator stalk switch _____ 101
Direction indicators
______________ 101
Dome light, Convertible
__________ 232
Dome light, SportSedan __________ 232
Donor battery, boost starting
______ 200
Door handles
___________________ 48
Door mirrors
___________________ 124
Drive belt
______________________ 219
Drive belt, length
________________ 293
Driver’s seat with memory
_________ 21
Driving at night
_________________ 197
Driving in cold climates
___________ 187
Driving in deep water
____________ 196
Driving in hot climates ____________ 189
Driving techniques
______________ 185
Driving with a compact wheel fitted
_260
Driving with a heavy load on hilly
roads
________________________ 167
Driving with a load
______________ 196
Driving with a roof load ___________ 194
Driving with the trunk lid open
______ 196
EEasy entry, Convertible
____________ 73
EDR (Event Data Recorders)
______ 284
ESP®
________________________ 177
Economical motoring
____________ 185
Electrical system, technical data
____ 292Electrically adjustable seats
________ 20
Electric engine heater
____________ 186
Electric heating, front seats
________ 115
Electric windows
________________ 121
Electric windows, Convertible
_______ 77
Electronic Stability Program
_______ 177
Electronic steering wheel lock ______ 154
Emergency opening of the narrow
backrest, SportSedan
___________ 142
Emergency operation of the moonroof
132
Engine bay, cleaning
_____________ 267
Engine heater
__________________ 186
Engine immobilizer
_______________ 55
Engine management system
______ 206
Engine number
_________________ 299
Engine oil, checking
_____________ 210
Engine oil, grade
________________ 290
Engine oil, volume _______________ 291
Engine temperature gauge
_________ 88
Engine, description
______________ 205
Engine, technical data ____________ 289
Engines
_______________________ 292
Event Data Recorders (EDR)
______ 284
Extra electrical socket
____________ 136
FFacilitating entry to rear seat,
Convertible
____________________ 73
Factors affecting fuel consumption
__ 185
Filler cap
______________________ 160
Filling a portable fuel container
_____ 161Filling up
______________________ 159
Flat spots, tires
_________________ 246
Floor jack
______________________ 263
Folding down the rear seat backrest,
SportCombi
___________________ 143
Folding down the rear seat,
SportSedan ___________________ 138
Front fog lights __________________ 100
Front towing eye ________________ 197
Fuel container
__________________ 161
Fuel gauge
_____________________ 89
Fuel grade _____________________ 291
Fuel information
_________________ 161
Functions, car alarm
______________ 58
Fuse panel in luggage compartment
_240
Fuse table
_____________________ 239
Fuses
_________________________ 237
GGDO, garage door opener
_________ 126
Gearbox number
________________ 299
General safety instructions,
Convertible
____________________ 62
Glove box
_____________________ 136
Glovebox lighting
________________ 233
HHandbrake
_____________________ 179
Hazard warning lights
____________ 102
93_US_M08.book Page 304 Friday, May 11, 2007 11:37 AM
ProCarManuals.com