2008 RENAULT SCENIC component 138

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B -111
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B -111V9 MR-372-J84-87B000$344.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
DF073
CONTINUED
Check the insulation and continuity of the following connection:
●Connection code AP43 between components 645 and 1337.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the insulation and continuity of the following connection:
●Connection code 20W between components 645 and 138.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B-112
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B-112V9 MR-372-J84-87B000$344.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
DF074
PRESENT
OR
STOREDLEFT-HAND DOOR CHILD SAFETY LOCK CIRCUIT
CC: Short circuit
CO: Open circuit
CO/
CC
NOTESUse Wiring Diagrams Technical Note for MEGANE II or
SCENIC II.
Check the condition and connection of the child safety lock switch connector.
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check for + 12 V on connection BPT of component 135.
Check for + after ignition feed on connection AP43 of component 135.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for earth on connection MAS of component 135.
If the connection is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the condition and connection of the UCH PE1 and PP2 connectors.
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation and continuity of the following connection:
●Connection code 20AL,
between components 645 and 135.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the insulation and continuity of the following connection:
●Connection code AP43,
between components 645 and 1337.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the insulation and continuity of the following connection:
●Connection code 20BD,
between components 645 and 138.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF074 /UCH_V48_DF074/UCH_V4C_DF074/
UCH_V4D_DF074/UCH_V4F_DF074/UCH_V50_DF074

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -174
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -174V9 MR-372-J84-87B000$473.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ET052
REAR RIGHT-HAND DOOR
NOTESThere must be no present or stored faults.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Check the condition and connection of the PE1 connector of the UCH (tabs bent, broken, oxidised etc.).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of the rear right-hand door lock connector (bent, broken, oxidised tabs, etc.).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation and continuity of the following connection:
●Connection code 87B between components 645 and 138.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check:
The insulation of component 138 on connections 87B and MAQ (door open).
The continuity of component 138 on connections 87B and MAQ (door closed).
Replace the lock if it is not correct.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_ET052/UCH_V48_ET052/ UCH_V4C_ET052/
UCH_V4D_ET052 /UCH_V4F_ET052/UCH_V50_ET052

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -175
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -175V9 MR-372-J84-87B000$473.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ET053
DRIVER'S DOOR
NOTESThere must be no present or stored faults.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Check the condition and connection of the PE1 connector of the UCH (tabs bent, broken, oxidised etc.).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of the driver's side door lock connector (bent, broken, oxidised tabs, etc.).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation and continuity of the following connection:
●Connection code 87H between components 645 and 140.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check:
The insulation of component 138 on connections 87B and MAQ (door open).
The continuity of component 138 on connections 87B and MAQ (door closed).
Replace the lock if it is not correct.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_ET053/UCH_V48_ET053/ UCH_V4C_ET053/
UCH_V4D_ET053 /UCH_V4F_ET053/UCH_V50_ET053

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses87B
87B - 235
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses87B
87B - 235V9 MR-372-J84-87B000$602.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50 PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
ET159
ET160
REAR LEFT-HAND DOOR CHILD SAFETY LOCK
REAR RIGHT-HAND DOOR CHILD SAFETY LOCK
NOTESNo faults should be present or stored.
Check that configuration LC035 Child safety lock is WITH, if not perform configuration
using specific command SC016 Child safety lock (see Configurations and
programming). Status only visible if Vdiag 4C, 4D, 4F and 50 UCH.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
IMPORTANT
After disconnecting the battery, there may be an inconsistency between a request on the switch and the status of
one or two lock(s).
In this case, deactivate and reactivate the switch until the warning light comes on when the switch is pressed.
Check the condition and connection of the lock connector (broken, bent, oxidised tabs).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of the PP2 connector of the UCH (tabs broken, bent, oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check for earth on connection MZ of component 139 or on connection MAQ of component 138.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●Connection code 87A between components 645 and 139.
●Connection code 87B between components 645 and 138.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Replace the faulty lock.
If the fault is still present, contact Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_ET159/UCH_V48_ET159/ UCH_V4C_ET159/UCH_V4D_ET159/
UCH_V4F_ET159 /UCH_V50_ET159/UCH_V44_ET160/UCH_V48_ET160/
UCH_V4C_ET160 /UCH_V4D_ET160/UCH_V4F_ET160 /UCH_V50_ET160
MR-372-J84-87B000$602.mif

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 249
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 249V9 MR-372-J84-87B000$774.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
AC004
LOCK DOORS AND BOOT
NOTESNo faults should be present or stored.
This command is for testing locking relay operation.
Note:
The driver's door circuit is shared with the fuel tank flap circuit.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
One or more doors do not lock when the command is activated.
Check the condition and connection of the PP2 connector on the UCH.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of the connector on the faulty lock(s).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check for earth on the following connections:
●Connection code MAM.
●Connection code 87H of component 140.
●Connection code MZ.
●Connection code 87A of component 139.
●Connection code MAN.
●Connection code 87G of component 141.
●Connection code MAQ.
●Connection code 87B of component 138.
●Connection code 20BC.
●Connection code 20BH of component 844.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If faulty: If OK:
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 250
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 250V9 MR-372-J84-87B000$774.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
AC004
CONTINUED
Check for the + 12 V feed with the command running on the following connections:
●Connection code 20BK.
●Connection code 20BD for components 138, 139 and 141.
●Connection code 20BH.
●Connection code 20BH for components 140 and 844.
If the + 12 V feed between the connections is correct, replace the faulty lock(s).
If faulty:
Check the insulation and continuity of the following connections:
●Connection code 20BC.
●Connection code 20BH between components 645 and 140.
●Connection code 20BC.
●Connection code 20BH between components 645 and 844.
●Connection code 20BD.
●Connection code 20BK between components 645 and 138.
●Connection code 20BD.
●Connection code 20BK between components 645 and 139.
●Connection code 20BD.
●Connection code 20BK between components 645 and 141.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 251
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 251V9 MR-372-J84-87B000$774.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
AC005
AC006
UNLOCK DOORS AND BOOT
DRIVER'S DOOR UNLOCKING
NOTESNo faults should be present or stored.
This command is for testing unlocking relay operation.
The driver's door circuit is shared with the fuel tank flap circuit.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
One or more doors do not unlock when the commands are activated.
Check the condition and connection of the PP2 connector on the UCH.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of the connector on the faulty lock(s).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check for earth on:
●Connection code MAM.
●Connection code 87H.
Of component 140.
●Connection code MZ.
●Connection code 87A.
Of component 139.
●Connection code MAN.
●Connection code 87G.
Of component 141.
●Connection code MAQ.
●Connection code 87B.
Of component 138.
●Connection code 20BC.
●Connection code 20BH.
Of component 140.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If faulty: If OK:
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.