2008 RENAULT SCENIC wheel

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of parameters
87B
87B -245
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of parameters
87B
87B -245V9 MR-372-J84-87B000$688.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
* FR: Front
* RR: Rear
PR009
PR010
PR011
PR012FR* WHEEL LOW SPEED REC* PRESSURE
RR* WHEEL LOW SPEED REC* PRESSURE
RR* WHEEL HIGH SPEED REC* PRESSURE
FR* WHEEL HIGH SPEED REC* PRESSURE
NOTESThere must be no present or stored faults.
Carry out this fault finding procedure after detecting a discrepancy between the
pressures recommended by the manufacturer and those stored in the UCH.
Warning:
Use Workshop Repair Manual 364 (Mégane II) or 370 (Scénic II) or refer to the
pressure label attached to the driver's door to obtain the recommended pressures for
the tyres actually installed on the vehicle.
If, after comparing with the manufacturer's data (see MR 364 (Mégane II) or MR 370 (Scénic II), 35A), the
recommended pressures stored in the UCH do not conform, reprogram the recommended pressures using
command VP005 Enter recommended pressures (see Configurations and programming).
If the recommended pressures cannot be entered properly, contact Techline.
AFTER REPAIRRepeat the check from the start.
UCH_V44_PR009/UCH_V48_PR009/UCH_V4C_PR009/UCH_V4D_PR009/UCH_V4F_PR009/UCH_V50_PR009/UCH_V44_PR010/
UCH_V48_PR010/UCH_V4C_PR010/UCH_V4D_PR010/UCH_V4F_PR010/UCH_V50_PR010/UCH_V44_PR011/UCH_V48_PR011/
UCH_V4C_PR011/UCH_V4D_PR011/UCH_V4F_PR011/UCH_V50_PR011/UCH_V44_PR012/UCH_V48_PR012/UCH_V4C_PR012/
UCH_V4D_PR012/UCH_V4F_PR012/UCH_V50_PR012

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Customer complaints
87B
87B -299
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Customer complaints
87B
87B -299V9 MR-372-J84-87B000$860.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
TYRE PRESSURE MONITOR
"ADJUST TYRE PRESSURE" MESSAGE APPEARS (WHEEL
CONCERNED IS HIGHLIGHTED ON THE DISPLAY)ALP52
"ADJUST TYRE PRESSURE" MESSAGE APPEARS (2 WHEELS
BECOME HIGHLIGHTED ON THE DISPLAY)ALP53
"TYRE SENSOR FAULT" MESSAGE APPEARS (WHEEL WARNING
LIGHT DISAPPEARS)ALP54
"TYRE SENSOR FAULT" MESSAGE APPEARS (4 WHEEL WARNING
LIGHTS DISAPPEAR)ALP55
"PUNCTURE: CHANGE WHEEL" MESSAGE APPEARS (THE WHEEL
IS HIGHLIGHTED ON THE DISPLAY)ALP56

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -372
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -372V9 MR-372-J84-87B000$989mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP47 Steering column lock does not unlock
NOTES–The immobiliser warning light flashes normally,
–the card reader does not flash,
–there is a message on the instrument panel Column not unlocked or Turn
steering wheel + Start.
Check that the steering column is not under any mechanical stress (e.g.: wheel(s) jammed against pavement).
If the steering column is under stress, try to start the vehicle again by lifting the steering column (and pulling the
card out of the reader if a message requests this).
Check the consistency of statuses ET072 Steering column lock and ET073 Steering column lock signal.
In the event of a fault, see the procedure for these statuses in the UCH section.
Check that the steering column lock belongs to the vehicle using status ET248 Steering column lock immobiliser
code.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
UCH_V44_ALP47 /UCH_V48_ALP47/UCH_V4C_ALP47/
UCH_V4D_ALP47/UCH_V4F_ALP47/UCH_V50_ALP47

87B-385
AFTER REPAIRCarry out a complete check with the diagnostic tool.
V9 MR-372-J84-87B000$990.mif
87B
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
Note: In Vdiag 44 vehicles, the Service warning light comes on with the instrument panel message.
ALP 52"Adjust tyre pressure" message appears
(the wheel concerned is highlighted on the display)
NOTESCheck that all the faulty tyres are fitted with tyre pressure monitor valves.
Make sure the tyre has the recommended
pressure specified on the label or in the
driver's handbook (not under- or over-
inflated).
Are the tyres at the recommended
pressures?Readjust the tyre inflation pressure.
Read the pressures in PR003
to PR006.
Do PR003 to PR006 match
the readings taken with the
pressure gauge (to within
0.2 bar)?Read the recommended
pressures in the UCH
(PR009 to PR012)
Do the values of these
parameters match the
manufacturer's
recommended
pressures?Write the recommended
pressures with command
VP005 Enter
recommended
pressures.
Program the four valve codes and reinstall the coloured rings in the
position indicated on the label on the driver's side.
NO
YES
YES
NO
ANO
YES
UCH_V44_ALP52 / UCH_V48_ALP52 / UCH_V4C_ALP52 / UCH_V4D_ALP52 / UCH_V4F_ALP52 / UCH_V50_ALP52
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart

87B-387
AFTER REPAIRCarry out a complete check with the diagnostic tool.
V9 MR-372-J84-87B000$990.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP 53"Adjust tyre pressure" message appears
(2 wheels are highlighted on the display)
Note:
In Vdiag 44 vehicles, the Service warning light comes on with the instrument panel message.
NOTESCheck that all the faulty tyres are fitted with tyre pressure monitor valves.
Is there a pressure
imbalance between the left-
hand and right-hand tyre on
the same axle?Check the positions of
the coloured rings
against the label on the
driver's side.
Program the four valve
codes and reinstall the
coloured rings in the
position indicated on
the label on the driver's
side. Have the front and rear
tyres been swapped?
Adjust the tyre pressure to the
manufacturer's recommended
levels.
Is the fault still present?End of fault finding.
NO
YESYES
NO
B
NO
YES
A
UCH_V44_ALP53 / UCH_V48_ALP53 / UCH_V4C_ALP53 / UCH_V4D_ALP53 / UCH_V4F_ALP53 / UCH_V50_ALP53

87B-389
AFTER REPAIRCarry out a complete check with the diagnostic tool.
V9 MR-372-J84-87B000$990.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP 54"Tyre sensor fault" message appears
(wheel warning light disappears)
NOTESCheck that all the faulty tyres are fitted with tyre pressure monitor valves.
Perform the necessary
work on the wheel with a
tyre pressure monitor
valve, then reinstall it on
the vehicle. Has one of the wheels been
replaced with the spare?
Program the four valve codes with
command SC002 Program the 4
valve codes.
Did the programming procedure
go properly?
End of fault
finding.
Replace the faulty valve.
YES
NO
NOYES
UCH_V44_ALP54 / UCH_V48_ALP54 / UCH_V4C_ALP54 / UCH_V4D_ALP54 / UCH_V4F_ALP54 / UCH_V50_ALP54

87B-390
AFTER REPAIRCarry out a complete check with the diagnostic tool.
V9 MR-372-J84-87B000$990.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP 55"Tyre sensor fault" message appears
(4 wheel warning lights disappear)
NOTESCheck that all the faulty tyres are fitted with tyre pressure monitor valves.
Are the wheels fitted with tyre pressure
monitor valves?Either install tyre pressure monitor valves, or
deconfigure tyre pressure monitor in the
instrument panel.
Check the tyre pressure monitor configuration
in the UCH (LC017 Tyre pressure monitor
function).
Is the UCH configured "with" the tyre
pressure monitor function?Configure the UCH with the tyre pressure monitor
function using command CF023 Tyre pressure
monitor function under SC008 UCH type.
Program the four valve codes with command
SC002 Program the 4 valve codes. Have the valve codes been programmed?
Check that the ABS is transmitting the vehicle
speed (PR008 Vehicle speed).
Is there an ABS fault?Run full fault finding on the ABS.
UCH fault, contact Techline.
NO
YES
NO
YES
NO
YES
YES
NO
UCH_V44_ALP55 / UCH_V48_ALP55 / UCH_V4C_ALP55 / UCH_V4D_ALP55 / UCH_V4F_ALP55 / UCH_V50_ALP55

87B-391
AFTER REPAIRCarry out a complete check with the diagnostic tool.
V9 MR-372-J84-87B000$990.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP 56"Stop! Tyre puncture" message appears
(the wheel is highlighted on the display)
NOTESNone.
Is the tyre punctured?Repair the tyre.
Check the pressure in all 4 tyres with a
pressure gauge (problem: severe under-
inflation).
Is the pressure correct?
Make sure the valve seal is not damaged.
Check that the sealing nut on the valve is one for
valves installed on the Mégane II or Scénic II, and
not one for a Laguna II, Vel Satis or Espace IV. Read the recommended pressures in the UCH
(PR009 to PR012).
Do the values of these parameters match
the manufacturer's recommended
pressures?
After all these checks, if the message still appears
on the instrument panel, contact Techline.
Write the recommended
pressures with command VP005
Enter recommended pressures.
Contact the Techline.
YES
NO
NO
YES
NOYES
UCH_V44_ALP56 / UCH_V48_ALP56 / UCH_V4C_ALP56 / UCH_V4D_ALP56 / UCH_V4F_ALP56 / UCH_V50_ALP56