2008 RENAULT SCENIC display

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-65
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-65V9 MR-372-J84-87B000$215.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
9) CONFIGURATION PROCEDURE FOR THE TYRE PRESSURE MONITOR FUNCTION (CF023)
10) INSTRUMENT PANEL CONFIGURATION PROCEDURE (CF145)CF023:
TYRE PRESSURE MONITOR FUNCTION
(in programming command SC008 "UCH type")
WRITING THE CONFIGURATION WITH
OR WITHOUT TYRE PRESSURE MONITOR:
●Select the Repair mode menu.
●Select the Programming menu.
●Select line SC008 then line CF023, then With or Without.
●Confirm the selection.
●Check that sure the configuration has been properly stored by checking the Read configuration menu at line
LC017 Tyre pressure monitor function.
IMPORTANT:
CONFIGURATION INCONSISTENCY BETWEEN THE INSTRUMENT PANEL AND UCH
1st case–The instrument panel detects that the tyre pressure monitor is programmed in the UCH but
not its proper configuration. The message ELECTRONIC FAULT appears, then the
4 wheels disappear on the instrument panel display, and the Service warning light comes
on.
2nd case–The instrument panel detects that the tyre pressure monitor is programmed in its own
configuration but the UCH fails to respond to any requests from the instrument panel (not
configured in UCH). The message TYRE SENSOR FAULT will appear, the four wheels
will disappear from the instrument panel display and the Service warning light will come
on.
CF145:
TYRE PRESSURE MONITOR
●After the multiplex network test, select Instrument panel.
●Select Repair mode.
●Select Write configuration.
●Select line CF145, then With or Without.
●Confirm the selection.
●Check that the configuration has been properly stored in the Read configuration menu at line LC056 Tyre
pressure monitor.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B-117
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B-117V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
MAIN COMPUTER STATUSES AND PARAMETERS
SR.*: sunroof.Note:
Certain statuses and parameter do not affect all the Vdiags.
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-functionParameter or
Status
checked Action Display and Notes Fault finding
UCHPR001:Battery voltage9 V < X < 16 VIn the event of a fault,
consult the interpretation
of parameter PR001.
ET014:Control power
levelNONE
ACCESSORIES FEED
TIMED
APCNone
ET087:One-touch
window control/
SR.*
authorisationACTIVE
INACTIVEIn the event of a fault, refer
to the interpretation of
status ET087.
ET098:ADAC* buttonDEPRESSED
RELEASEDIn the event of a fault,
consult the interpretation
of status ET098.
ET195:UCH frequency
(IN MHz)315
433None
ET205:Type of UCH RF
aerialINTERNAL
EXTERNALNone
ET010:Card frequency
(in MHz)315
433None
UCH_V44_CCONF/UCH_V48_CCONF/UCH_V4C_CCONF/
UCH_V4D_CCONF/ UCH_V4F_CCONF/UCH_V50_CCONF
MR-372-J84-87B000$387.mif

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B-118
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B-118V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
KEYLESS VEHICLE FUNCTION
Sub-function: Access
RF*: Radio frequency.
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-functionParameter or
Status
checked Action Display and Notes Fault finding
AccessPR013:Number of cards
programmed1
2
3
4None
ET010:Card frequency
(in MHz)315
433None
ET195:UCH frequency
(in MHz)315
433None
ET205:Type of UCH
RF* aerialINTERNALNone
ET066:Card detected
buttonYES
NO In the event of a fault,
consult the interpretation
of status ET066.
ET067:Card button
press
recognisedYES
NO In the event of a fault,
consult the interpretation
of status ET067.
ET054:Optical sensors
suppliedYES
NO In the event of a fault,
consult the interpretation
of status ET054.
ET055:Front driver side
optical sensorACTIVE
INACTIVE In the event of a fault,
consult the interpretation
of status ET055.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B-119
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B-119V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
KEYLESS VEHICLE FUNCTION
Sub-function: Access (continued 1):
*lckg: Locking
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-functionParameter or
Status
checked Action Display and Notes Fault finding
AccessET056:Rear driver side
optical sensorACTIVE
INACTIVEIn the event of a fault,
consult the interpretation
of status ET056.
ET057:Passenger side
front/rear optical
sensorACTIVE
INACTIVEIn the event of a fault,
consult the interpretation
of status ET057.
ET058:Lckg* button on
driver's side
handles DEPRESSED
RELEASEDIn the event of a fault,
consult the interpretation
of status ET058.
ET059:Lckg* buttons on
passenger's side
handlesDEPRESSED
RELEASEDIn the event of a fault,
consult the interpretation
of status ET059.
ET060:Tailgate locking
buttonDEPRESSED
RELEASEDIn the event of a fault,
consult the interpretation
of status ET060.
ET086:Electric child
safety lockACTIVE
INACTIVESignal interpreted if
vehicle configured WITH
Child safety lock.
ET053:Driver's doorOPEN
CLOSED In the event of a fault, refer
to the interpretation of
status ET053.
ET042:Passenger doorOPEN
CLOSED In the event of a fault, refer
to the interpretation of
status ET042.
ET194:Passenger's
door or bonnetOPEN
CLOSED In the event of a fault, refer
to the interpretation of
status ET042.
ET051:Rear left-hand
doorOPEN
CLOSED In the event of a fault, refer
to the interpretation of
status ET051.
ET052:Rear right-hand
doorOPEN
CLOSED In the event of a fault, refer
to the interpretation of
status ET052.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -120
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -120V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
KEYLESS VEHICLE FUNCTION
Sub-function: Access (continued 2)
*CPE: Electric central door locking
SR.*: Sunroof
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-functionParameter or
Status
checked Action Display and Notes Fault finding
AccessET061:Open tailgate
requestPRESENT = Tailgate
opening button pressed.
ABSENT = Button not
pressed.In the event of a fault, refer
to the interpretation of
status ET061.
ET050:Tailgate/BootOPEN
CLOSED In the event of a fault,
consult the interpretation
of status ET050.
ET062:Open rear
screen requestABSENT
PRESENTNone
ET041:Opening rear
screenOPEN
CLOSED None
ET044:CPE* buttonPRESSED
RELEASEDIn the event of a fault,
consult the interpretation
of status ET044.
ET233:Child safety lock
switchPRESSED
RELEASEDIn the event of a fault,
consult the interpretation
of status ET233.
ET230:Child safety lockACTIVE
INACTIVEIn the event of a fault,
consult the interpretation
of fault DF072.
ET160:Rear right-hand
door Child safety
lockACTIVE
INACTIVEIn the event of a fault, refer
to the interpretation of
status ET160.
ET159:Rear left-hand
door child safety
lockACTIVE
INACTIVEIn the event of a fault, refer
to the interpretation of
status ET159.
ET087:One-touch
window control/
SR.*
authorisation ACTIVE
INACTIVEIn the event of a fault, refer
to the interpretation of
status ET087.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -121
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -121V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
KEYLESS VEHICLE FUNCTION
Sub-function: Access (continued 3)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-
functionParameter or
Status
checked Action Display and Notes Fault finding
AccessET068:Most recently locked
byAUTOMATIC = automatic re-
locking if unlocked using the
card and the doors are not
used within 2 minutes of
unlocking.
CPE* = locking by pressing
the button on the centre
console
HANDS-FREE = locking via
door or tailgate handle switch
RAID* FUNCTION = Renault
Anti-Intruder Device.
Operates from around 3 mph
(5 km/h).
CARD = locking with the
DIAGNOSTIC card = Locking
by actuator AC004 Central
door locking
LONG CPE* = locking by
pressing and holding the
button on the centre console In the event of a fault,
refer to the
interpretation of status
ET068.
ET069:Most recently
unlocked by HANDS-FREE = optical
sensors
CPE* = electric door locking
button
CARD = with the card
FAULT FINDING = AC005
IMPACT INFO = info after
impact
AIRBAG = unlocking by the
AIRBAG computer after an
accidentIf status = Airbag,
carry out fault finding
on the Airbag
computer (see 88C,
Airbag and
pretensioners). In the
event of a fault,
consult the
interpretation of status
ET069.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -122
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -122V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
KEYLESS VEHICLE FUNCTION
Sub-function: Access (continued 4):
RAID*: Renault Anti-Intruder Device.
CPE*: Electric central door locking.
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-
functionParameter or
Status
checked Action Display and Notes Fault finding
AccessET088:Deadlocking
activation sourceCARD
HANDS-FREE
FAULT FINDINGIn the event of a fault,
consult the
interpretation of
status ET088.
ET090:Deadlocking
deactivation sourceCPE*
CARD
HANDS-FREE
FAULT FINDING
APC In the event of a fault,
consult the
interpretation of
status ET090.
ET043:RAID* function
authorisation by
CPE*.ACTIVE
INACTIVE In the event of a fault,
consult the
interpretation of status
ET043.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -123
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -123V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
KEYLESS VEHICLE FUNCTION
Sub-function: Protection
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-
functionParameter or
Status
checked Action Display and Notes Fault finding
ProtectionET070:Start buttonPRESSED
RELEASED In the event of a fault,
consult the
interpretation of
status ET070.
ET008:blank UCHYES = If the UCH is blank.
NO = If the UCH is
programmed. In the event of a fault,
consult the
interpretation of
status ET008.
PR013:Number of cards
programmed1, 2, 3 or 4None
ET071:Unprogrammed
steering column lockYES
NO In the event of a fault,
consult the
interpretation of status
ET071.
ET119:UCH request to
steering column lockLOCKING UNLOCKINGNone
ET248:Steering column
lock immobiliser
codeINCORRECT
OKNone
ET073:Steering column
lock sensor signalFAULTY
UNLOCKED
UNDETERMINED
FALSELY TRIGGERED
SHORT CIRCUITIn the event of a fault,
consult the
interpretation of status
ET073.
ET072:Steering column
lockINCONSISTENCY
LOCKED
UNLOCKEDIn the event of a fault,
consult the
interpretation of status
ET072.
ET014:Control power levelNONE
ACCESSORIES FEED
TIMED
APCNone