2008 RENAULT SCENIC ABS

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B -104
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B -104V9 MR-372-J84-87B000$344.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
DF031
PRESENT
OR
STOREDONE TOUCH WINDOW CONNECTION
CC.1: Short circuit to + 12 V
CO.0: Open circuit or short circuit to earth
NOTESConditions for applying the fault finding procedure to a stored fault:
If the fault becomes present after a one-touch window has been activated, then apply
this fault finding procedure.
Special note: If the vehicle is not fitted with one-touch windows, ignore this fault. Refer
to the information about Electric windows in the Fault finding chart section.
If the vehicle has Mégane II ph2 bodywork: see MR 366 Fault finding, 87D, Electric
windows - Sunroof.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Check the condition and connection of the electric window connector (tabs bent, broken, etc.).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of the connector PE2 of the UCH (tabs bent, broken, etc.).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation and continuity of the following connection:
●Connection code 21K.
Between components:
–645 and 202,
–645 and 203,
–645 and 204,
–645 and 304.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF031 /UCH_V48_DF031/UCH_V4C_DF031/
UCH_V4D_DF03 1/UCH_V4F_DF031/UCH_V50_DF031

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B -105
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B -105V9 MR-372-J84-87B000$344.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
DF032
PRESENT
OR
STOREDBOOT EXTERNAL AERIAL
CO.1: Short circuit or open circuit to + 12 V
NOTESConditions for applying the fault finding procedure to a stored fault:
Activation of command AC037: Transmitter aerial fault finding; if the fault becomes
present, then carry out this fault finding procedure.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Check the condition and connection of the external boot aerial connector (tabs bent, broken, etc.).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of the PE3 connector of the UCH (tabs bent, broken, etc.).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation and the continuity of the following connections:
●Connection code 26AM,
●Connection code 26AN.
Between components 645 and 1378.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Replace the aerial if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF032 /UCH_V48_DF032/UCH_V4C_DF032/
UCH_V4D_DF03 2/UCH_V4F_DF032/UCH_V50_DF032

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B -106
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B -106V9 MR-372-J84-87B000$344.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
DF033
PRESENT
OR
STOREDDRIVER'S SIDE EXTERNAL AERIAL(S)
CO.1: Short circuit or open circuit to + 12 V
NOTESConditions for applying the fault finding procedure to a stored fault:
Activation of command AC037: Transmitter aerial diagnostic; if the fault appears,
then carry out this fault finding procedure.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Check the condition and connection of the driver's side external aerial connector (tabs bent, broken, etc.).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of the PE3 connector of the UCH (tabs bent, broken, etc.).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation and the continuity of the following connections:
●Connection code 26AA,
●Connection code 26AB,
●Connection code 26AH,
●Connection code 26AG.
Between components:
–645 and 1374,
–645 and 1376.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Disconnect one aerial then the other to identify which is the cause of the fault.
(The aerials are connected by side, a short circuit in one aerial affects all the aerials on the same side).
Replace the aerial if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF033 /UCH_V48_DF033/UCH_V4C_DF033/
UCH_V4D_DF03 3/UCH_V4F_DF033/UCH_V50_DF033

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B -107
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B -107V9 MR-372-J84-87B000$344.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
DF034
PRESENT
OR
STOREDPASSENGER SIDE EXTERNAL AERIAL(S)
CO.1: Short circuit or open circuit to + 12 V
NOTESConditions for applying the fault finding procedure to a stored fault:
Activation of command AC037: Transmitter aerial fault finding; if the fault becomes
present, then carry out this fault finding procedure.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Check the condition and connection of the passenger's side external aerial connector (tabs bent, broken, etc.).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of the PE3 connector of the UCH (tabs bent, broken, etc.).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation and the continuity of the following connections:
●Connection code 26AC,
●Connection code 26AD,
●Connection code 26AL,
●Connection code 26AK.
Between components:
–645 and 1375,
–645 and 1377.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Disconnect one aerial then the other to identify which is the cause of the fault.
(The aerials are connected by side, a short circuit in one aerial affects all the aerials on the same side).
Replace the aerial if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF034 /UCH_V48_DF034/UCH_V4C_DF034/
UCH_V4D_DF03 4/UCH_V4F_DF034/UCH_V50_DF034

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B -108
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B -108V9 MR-372-J84-87B000$344.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
DF035
PRESENT
OR
STOREDINTERNAL AERIALS CIRCUIT
CO.1: Short circuit or open circuit to + 12 V
NOTESConditions for applying the fault finding procedure to a stored fault:
Activation of command AC037: Transmitter aerial fault finding; if the fault becomes
present, then carry out this fault finding procedure.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Check the condition and connection of the front internal aerial connector (tabs bent, broken, etc.).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of the PE3 connector of the UCH (tabs bent, broken, etc.).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the continuity and insulation to earth of the following connections:
●Connection code 26AT,
●Connection code 26AU,
●Connection code 26AX,
●Connection code 26AY,
●Connection code 26AV,
●Connection code 26AW.
Between components:
–645 and 1375,
–645 and 1377.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Disconnect the aerials one by one to identify which is the cause of the fault.
(The 3 aerials are interconnected in the UCH, a short circuit in one aerial affects all the aerials).
Replace the aerial if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF035 /UCH_V48_DF035/UCH_V4C_DF035/
UCH_V4D_DF03 5/UCH_V4F_DF035/UCH_V50_DF035

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -120
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -120V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
KEYLESS VEHICLE FUNCTION
Sub-function: Access (continued 2)
*CPE: Electric central door locking
SR.*: Sunroof
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-functionParameter or
Status
checked Action Display and Notes Fault finding
AccessET061:Open tailgate
requestPRESENT = Tailgate
opening button pressed.
ABSENT = Button not
pressed.In the event of a fault, refer
to the interpretation of
status ET061.
ET050:Tailgate/BootOPEN
CLOSED In the event of a fault,
consult the interpretation
of status ET050.
ET062:Open rear
screen requestABSENT
PRESENTNone
ET041:Opening rear
screenOPEN
CLOSED None
ET044:CPE* buttonPRESSED
RELEASEDIn the event of a fault,
consult the interpretation
of status ET044.
ET233:Child safety lock
switchPRESSED
RELEASEDIn the event of a fault,
consult the interpretation
of status ET233.
ET230:Child safety lockACTIVE
INACTIVEIn the event of a fault,
consult the interpretation
of fault DF072.
ET160:Rear right-hand
door Child safety
lockACTIVE
INACTIVEIn the event of a fault, refer
to the interpretation of
status ET160.
ET159:Rear left-hand
door child safety
lockACTIVE
INACTIVEIn the event of a fault, refer
to the interpretation of
status ET159.
ET087:One-touch
window control/
SR.*
authorisation ACTIVE
INACTIVEIn the event of a fault, refer
to the interpretation of
status ET087.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -128
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -128V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
FUNCTION: AIR CONDITIONING
Sub-function: Heating (continued)
*RCH = Passenger Compartment Heating Resistor
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-
functionParameter or
Status
checked Action Display and Notes Fault finding
HeatingET020:Number RCH*
activated.0, 1, 2, 3, 4 or 5In the event of a fault,
refer to the
interpretation of status
ET020.
ET021:RCH* 1 relay control ACTIVE
INACTIVE In the event of a fault,
consult the
interpretation of
status ET021.
ET022:RCH* 2 relay controlACTIVE
INACTIVE In the event of a fault,
consult the
interpretation of
status ET022.
ET023:RCH* 3 relay controlACTIVE
INACTIVEIn the event of a fault,
consult the
interpretation of
status ET023.
ET031:Fast idle speed
request for RCH*INACTIVE
Fast idle speed to prevent
battery dischargeIn the event of a fault,
consult the
interpretation of status
ET031.
ET169:EngineSTOPPEDIn the event of a fault,
refer to the
interpretation of
status ET169.
ET025:Retractable roofCLOSED
NOT CLOSED
ABSENTIn the event of a fault,
consult the
interpretation of status
ET025.
ET026:Heated rear screen
switchACTIVE
INACTIVEIn the event of a fault,
consult the status
interpretation ET026.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -130
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -130V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
FUNCTION: TYRES
Sub-function: Tyre approval
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-functionParameter or
Status
checked Action Display and Notes Fault finding
Tyre receiver ET040:Tyre pressure
monitoring systemNOT WORKING
ACTIVE If status ET040 is OUT OF
ORDER, consult the fault
finding procedure for status
ET040.
ET032:Front left-hand
wheel valve signalOK
ABSENT
OVER-INFLATED
PUNCTURE
UNDER-INFLATEDCheck that the tyre pressure is
at the recommended pressure
(see MR 364 (Mégane II) or
MR 370 (Scénic II),
Mechanical, 35A, Tyre
pressure: Identification).
If status ET032 is not OK,
consult the fault finding
procedure for status ET032.
PR003:Front left-hand
wheel pressure0 bar < X < 3.55 barIf X = 0 bar, consult the fault
finding procedure for parameter
PR003.
Check that the recommended
pressure (PR009 to PR012)
corresponds correctly to the
vehicle.
PR019:Front left-hand tyre
temperature- 40ºC normal that the temperature is
50˚C and the pressure is 0 bar.
Perform a road test so that the
sensor emits the actual
temperature and pressure.
ET0033:Front right-hand
wheel valve signalOK
ABSENT
OVER-INFLATED
FLAT
UNDER-INFLATEDCheck that the tyre pressure is
at the recommended pressure
(see MR 364 (Mégane II) or
MR 370 (Scénic II),
Mechanical, 35A, Tyre
pressure: Identification).
If status ET033 is not OK,
consult the fault finding
procedure for status ET033.