2008 RENAULT SCENIC warning lights
[x] Cancel search: warning lightsPage 159 of 391
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -159
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -159V9 MR-372-J84-87B000$473.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ET032
ET033
ET034
ET035
CONTINUED
STEP 2
IMPORTANT:
Wait 1 minute and 30 seconds before checking the change of status.
–If the original status is: over-inflated or under-inflated
Consult ALP 52 "Adjust tyre pressure" message appears (the wheel concerned is highlighted on the
display) and ALP 56 "Adjust tyre pressure" message appears (2 wheels are highlighted on the display).
–If the original status is: puncture
Consult ALP 56 "Stop! Tyre puncture" message appears (the wheel is highlighted on the display).
–If the original status is: absent
Consult ALP 54 "Tyre sensor fault" message appears (wheel warning light disappears) and ALP 55 "Tyre
sensor fault" message appears (4 wheel warning lights disappear).
If the status does not change, replace the sensor on the wheel concerned by following the instructions and the
programming procedure for the four valve codes, SC002 Program 4 valve codes (see Configurations and
programming).
AFTER REPAIRDeal with any other possible faults.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
Page 211 of 391
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses87B
87B - 211
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses87B
87B - 211V9 MR-372-J84-87B000$559.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ET085
HAZARD WARNING LIGHTS BUTTON
NOTESNo faults should be present or stored.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
ET085 is Absent with button pressed.
Check the F16 15A fuse of the passenger compartment fuse and relay box on the left-hand side of the centre
console.
Replace it if necessary.
Check the door/warning switch connector (e.g.: connector properly connected, tabs bent, broken, oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the PE2 and PE1 connectors (e.g. connector properly connected, tabs bent, broken, oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check for + 12 V on connection LPG of component 1391.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation and continuity of the following connections:
●Connection code 64F.
●Connection code 64Q between components 645 and 1391.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the following connections on component 1391 (button pressed):
●Connection code 64F.
●Connection code 64Q.
If there is insulation, replace the button.
If there is continuity, contact the techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_ET085/UCH_V48_ET085/ UCH_V4C_ET085/
UCH_V4D_ET085 /UCH_V4F_ET085/UCH_V50_ET085
Page 246 of 391
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Command summary table87B
87B - 246
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Command summary table87B
87B - 246V9 MR-372-J84-87B000$731.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Command summary table
*RCH: Passenger Compartment Heating Resistor
*CPE: Electric central door locking
*SR.: SunroofTool command Diagnostic tool title Vdiag
AC003Immobiliser warning light
V44, V48,
V4C, V4D,
V4F, V50 AC004Central door locking
AC005Central door unlocking
AC006Driver's door unlocking
AC007Rear screen wiper
AC008Front fog lights
AC009Rear fog lights
AC015Air conditioning button indicator light
AC016RCH* 1 relay
AC017RCH* 2 relay
AC018RCH* 3 relay
AC019Heated rear screen indicator light
AC020CPE* button indicator light
AC021Interior lights
AC022Left-hand direction indicator
AC023Right-hand direction indicator
AC024Card reader lighting
AC025One-touch window control/SR.* authorisation
AC026Start button lighting
AC027Footwell lights
AC030Headlight washer relay 1 (only if Vdiag 44 UPC)
AC031Headlight washer relay 2 (only if Vdiag 44 UPC)
AC032Driver's side external aerial testing
AC033Passenger's side external aerial testing
AC034Boot external aerial test
AC036Internal aerial test
AC037Transmitter aerial fault finding
AC076Child safety lock indicator light
MR-372-J84-87B000$731.mif
Page 299 of 391
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Customer complaints
87B
87B -299
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Customer complaints
87B
87B -299V9 MR-372-J84-87B000$860.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
TYRE PRESSURE MONITOR
"ADJUST TYRE PRESSURE" MESSAGE APPEARS (WHEEL
CONCERNED IS HIGHLIGHTED ON THE DISPLAY)ALP52
"ADJUST TYRE PRESSURE" MESSAGE APPEARS (2 WHEELS
BECOME HIGHLIGHTED ON THE DISPLAY)ALP53
"TYRE SENSOR FAULT" MESSAGE APPEARS (WHEEL WARNING
LIGHT DISAPPEARS)ALP54
"TYRE SENSOR FAULT" MESSAGE APPEARS (4 WHEEL WARNING
LIGHTS DISAPPEAR)ALP55
"PUNCTURE: CHANGE WHEEL" MESSAGE APPEARS (THE WHEEL
IS HIGHLIGHTED ON THE DISPLAY)ALP56
Page 364 of 391
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -364
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -364V9 MR-372-J84-87B000$989mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP39 Accessories feed not activated
NOTESCheck the voltage of the battery.
Start the fault finding procedure with the ignition off and the vehicle locked.
When the vehicle is unlocked, the instrument panel should light up for a moment.
If not, carry out fault finding on the multiplex network and instrument panel.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
The vehicle should switch to timed power (approximately 20 minutes) after the driver's door is opened (ET053
Driver's door).
If the timed supply is not triggered, try by:
–pressing the Start button (ET070 Start button), or
–turning on the hazard warning lights (ET085 "Hazard warning lights button"), or
–switching on the side lights (ET081 Lighting switch position).
If correct, run status fault finding for the faulty component.
If not correct, apply ALP No dialogue with the UCH.
The vehicle goes into accessories feed mode when the Start button is pressed (timed power active).
If it does not conform, check the operation of the Start button using status ET070 Start button and apply the fault
finding procedure associated with this status if necessary.
If the Start button operates correctly, use the fault finding procedure for status ET075 + accessories feed present.
Run fault finding and check the condition of the connectors of the + battery housing (Power fuses), of the power
board (maxi fuses), of the Protection and Switching Unit (UPC), of the Passenger Compartment Fuse and
Relay Box, of the Passenger Compartment Fuse and Relay Box option, and of the relay boards.
Check the condition and connection of the connectors on the UCH and the connectors on the UPC.
Check for + 12 V on connections BTP and 13AC of component 645.
Check for earth on connections 13E and NAM of component 645.
If one of the connectors is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
UCH_V44_ALP39 /UCH_V48_ALP39/UCH_V4C_ALP39/
UCH_V4D_ALP39/UCH_V4F_ALP39/UCH_V50_ALP39
Page 390 of 391
87B-390
AFTER REPAIRCarry out a complete check with the diagnostic tool.
V9 MR-372-J84-87B000$990.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP 55"Tyre sensor fault" message appears
(4 wheel warning lights disappear)
NOTESCheck that all the faulty tyres are fitted with tyre pressure monitor valves.
Are the wheels fitted with tyre pressure
monitor valves?Either install tyre pressure monitor valves, or
deconfigure tyre pressure monitor in the
instrument panel.
Check the tyre pressure monitor configuration
in the UCH (LC017 Tyre pressure monitor
function).
Is the UCH configured "with" the tyre
pressure monitor function?Configure the UCH with the tyre pressure monitor
function using command CF023 Tyre pressure
monitor function under SC008 UCH type.
Program the four valve codes with command
SC002 Program the 4 valve codes. Have the valve codes been programmed?
Check that the ABS is transmitting the vehicle
speed (PR008 Vehicle speed).
Is there an ABS fault?Run full fault finding on the ABS.
UCH fault, contact Techline.
NO
YES
NO
YES
NO
YES
YES
NO
UCH_V44_ALP55 / UCH_V48_ALP55 / UCH_V4C_ALP55 / UCH_V4D_ALP55 / UCH_V4F_ALP55 / UCH_V50_ALP55