2008 RENAULT SCENIC warning lights

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - System operation
87B
87B-15
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - System operation
87B
87B-15V9 MR-372-J84-87B000$086.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
1.1.6 Principle of Electric Childproof Locking:
The UCH controls the rear door locks to prevent them from being opened by means of the interior door handles and
inhibits operation of the rear electric window switches.
The switch statuses and the activation of electric childproof locks can be viewed using the following statuses:
–ET233 Child safety lock switch,
–ET159 Rear left-hand door child safety lock,
–ET160 Rear right-hand door child safety lock.
The configuration Child safety lock can be read using configuration LC035 Child safety lock and modified (see
Configurations and programming) using the specific command SC016 Child safety lock (Vdiag 4C, 4D, 4F and
50).
Fault finding can be performed on the child safety lock switch indicator light using command AC076 Child safety
lock indicator light.
1.1.7 Principle of Deadlocking:
The UCH controls the door locks to prevent unlocking via the interior handles. This function is activated by pressing
and holding (+ 2 seconds) the Renault card's locking button or by pressing the door locking button twice.
The direction indicators flash rapidly three times for deadlocking (in addition to the two flashes for locking).
For this function to operate, the vehicle must have deadlocking (2 motors) and configuration LC003 Deadlocking
must be WITH (see Configurations and programming). Deadlocking is configured using CF009 Deadlocking.
The source of the last deadlocking activation/deactivation can be viewed using statuses ET088 Deadlocking
activation source and ET090 Deadlocking deactivation source.
It is impossible to deadlock the vehicle if the + accessories feed is active, if the lights are switched on or if the hazard
warning lights are activated.
1.1.8 The valet card function, specific to certain countries (e.g. Mexico):
This function controls the valet card option which enables vehicles fitted with it to separately control unlocking of the
driver's door, the boot, or the passenger doors and the glovebox.
When the vehicle is electrically pre-equipped with the valet option and this option has been configured, the cards can
be used in two different customer modes. The "master" cards can unlock all the opening elements, but the "valet"
cards cannot unlock the glovebox, the boot and the passenger opening elements. They can only start the vehicle,
lock the whole vehicle, and unlock the driver's door. The function is configured with CF085 Valet card function
using the specific command SC008 UCH type. To access CF085, configure CF036 Selective opening element
opening to WITH.
To check that this function has been configured correctly, use LC016 Card valet function.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - System operation
87B
87B-22
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - System operation
87B
87B-22V9 MR-372-J84-87B000$086.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
1.1.13 Principle of automatic window relift:
When the doors are locked, and the lock button on the card is pressed twice in succession (or the door or boot if
the vehicle is fitted with hands-free function), the windows close automatically (as well as the sunroof, if fitted to
the vehicle).
The function is available on certain vehicles (see table below) depending on the number of one touch windows on
the vehicle and depending on the bodywork phases.
The automatic window relift function cannot be configured separately; it is automatically configured during special
command SC008 UCH type according to the vehicle type, number of one-touch windows and the production number
type.
1.1.14 Principle of new vehicle storage mode:
The vehicle is configured in this mode when it leaves the factory to optimise its power consumption:
–The immobiliser warning light is inhibited.
–The direction indicator warning lights are lit continuously on the instrument panel.
Before delivering the vehicle to the customer, deactivate this mode:
–By flipping down the steering column controls with the after ignition feed off.
–Or using command VP016 Deactivate new vehicle storage mode.
This function can only be activated in the factory with UCH Vdiag 4F or 50.If Then
Vehicle type One-touch window(s)Production
number typeFunction of automatic
window relift:
All except cabriolet phase 1 and 2
bodyworkWITHOUT WITHOUT
4-door phase 1 bodywork 1 driver OTW Jxxxxxx WITHOUT
4-door phase 1 bodywork 1 driver OTW OTHERS WITH
All except cabriolet and 4-door phase
1 bodywork1 driver OTW WITH
All except cabriolet phase 2 bodywork 1 driver OTW WITHOUT
All except cabriolet phase 1 and 2
bodywork2 or 4 OTW WITH
Cabriolet phase 1 and 2 bodywork WITHOUT WITHOUT

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - System operation
87B
87B-38
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - System operation
87B
87B-38V9 MR-372-J84-87B000$129.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - System operation
3 WIPER FUNCTION
3.1 Sub-function: WIPER CONTROL
The UCH receives the driver's request when the wiper stalk is used.
Windscreen wiper:
The UCH requests the Protection and Switching Unit via the CAN network to supply power to the windscreen wiper.
The park position is managed by the Protection and Switching Unit.
The wiper control stalk has four positions (neutral, intermittent wiping, slow speed and fast speed) and a wiper
intermittent speed ring which varies the time between each wipe.
Special notes:
If the windscreen wiper is set to low speed when the vehicle is moving and then the vehicle stops, the system switches
to intermittent wipe.
The requests made to the UCH by the wiper stalk can be displayed using statuses: ET077 Wiper stalk position and
ET096 Wiper intermittent speed ring.
If the vehicle is fitted with a rain sensor, (see special features of the rain and light sensor).
Rear screen wiper:
Rear wiper speed and power supply are also controlled by the UCH.
Windscreen wiper outside neutral position:
–The rear screen wiper starts to operate as soon as reverse gear is engaged and rain drops are detected on the
windscreen wiper.
–When the vehicle is stationary, the wipers operate intermittently every 7 seconds; over 36 mph (60 km/h) they
operate every 3 seconds. There is no continuous wiping function, except during the rear screen washer control.
The statuses corresponding to operation of the rear screen wiper can be displayed using statuses ET080 Rear
screen wiper request, ET097 Rear screen wiper park position and ET109 Reverse gear engaged or ET108
Automatic gearbox lever position, by configuration reading LC064 Rear screen wiper and by configuration
CF166 Rear screen wiper.
Windscreen washers:
The front and rear windscreen washers are controlled directly by the wiper control stalk, via a wire connection.
These connections are doubled up to the UCH to permit command status reading.
ET078 Windscreen washer request,
ET079 Rear screen washer request.
Special features of headlight washers
For vehicles fitted with xenon bulbs, the headlight washers are actuated at the same time as the windscreen washer,
only if the headlights are on.
Two cases are possible concerning the control of the headlight washers.
First case: (vehicles fitted with a SIEMENS Vdiag 44 UPC): the UCH sends the command by cable to two headlight
washer relays on a relay plate underneath the UPC.
Second case: (vehicles fitted with a LEAR Vdiag 48 or later): the UCH requests the UPC via the multiplex network to
activate the washer relays.
WARNING
If the UCH does not manage to determine the position of the control stalk, or inform the Protection and Switching
Unit of the control stalk's position, the Protection and Switching Unit will activate the windscreen wiper at low speed
(defect mode).
MR-372-J84-87B000$129.mif

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - System operation
87B
87B-43
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - System operation
87B
87B-43V9 MR-372-J84-87B000$129.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
4FUNCTION: LIGHTING
4.1 Sub-function: LIGHTING CONTROL
The UCH receives the request from the driver, from the lighting stalk, from the hazard warning lights button and, if
fitted to the vehicle, from the light detector.
The UCH requests the Protection and Switching Unit, via the multiplex network, to provide power to the side lights,
dipped headlights, main beam headlights and fog lights (front).
If a request to activate the lighting is made, the UPC provides power to the xenon bulb computers.
The dipped headlights are still supplied when the main beam headlights are activated.
The following statuses can be displayed:
ET081 Lighting stalk position.
ET082 Rear fog lights request.
ET085 Hazard warning lights switch.
ET083 Left-hand direction indicator request.
ET084 Right-hand indicator request.
If the UCH cannot determine the position of the control stalk, or inform the Protection and Switching Unit of the
control stalk's position, the Protection and Switching Unit will activate the dipped headlights.
4.2 Sub-function: LIGHTING POWER
The UCH controls the power supply for the rear fog light (a single one), direction indicators and interior lighting (roof
lights and footwell/floor lights).
The interior lighting request can be displayed using the ET112 Interior lighting control status.
Operation of the lights powered by the UCH can be checked using the actuator commands AC009 Rear fog lights,
AC022 Left-hand direction indicator, AC023 Right-hand direction indicator, AC021 Interior lights and AC027
Footwell/floor lighting.
Information displays Rain and light sensor Multiplex network
Steering column
controlUCHProtection and Switching
Unit
Rear fog light
Direction indicators
Interior lighting
Side lightsMain beam
headlights
Dipped
headlightsFront fog lights

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-66
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-66V9 MR-372-J84-87B000$215.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
The UCH configurations performed in accordance with the vehicle's equipment level are configured using
the CLIP tool:
Configuration
readingConfigurationName of
configurationChoice of
configurationVdiag
LC001Hands-free functionSC008 UCH typeWITH/WITHOUT44, 48, 4C, 4D, 4F
and 50
LC002External temperature
sensorCF029WITH/WITHOUT 4C, 4D, 4F and 50
LC003DeadlockingCF009WITH/WITHOUT44, 48, 4C, 4D, 4F
and 50
LC004One-touch window(s)SC008 UCH typeWITH/WITHOUT 4C and 4D
LC005Gearbox typeCF011Manual/
Automatic44, 48, 4C, 4D, 4F
and 50
LC006Rain detectorSC008 UCH typeWITH/WITHOUT 44, 48, 4C, 4D
LC007Light sensorSC008 UCH typeWITH/WITHOUT 44, 48, 4C, 4D
LC008Daytime running lightsCF014WITH/WITHOUT44, 48, 4C, 4D, 4F
and 50
LC009Hazard warning lights
illuminated upon impactAutomatic
configurationWITH/WITHOUT 44, 48, 4C, 4D
LC010Tyre type Run flat tyreSC008 UCH typeWITH/WITHOUT44, 48, 4C, 4D, 4F
and 50
LC011Vehicle typeSC008 UCH typeCabriolet/3-door/
All except E and
C44, 48, 4C, 4D
LC012Automatic relockingCF018WITH/WITHOUT 44, 48, 4C, 4D
LC013Type of air conditioningSC008 UCH typeHeating/
Automatic/
Manual 44, 48, 4C, 4D, 4F
and 50
LC014Type of driving styleCF020LEFT-HAND/
RIGHT-HAND 44, 48, 4C, 4D, 4F
and 50
LC015Front fog lightsCF021WITH/WITHOUT44, 48, 4C, 4D, 4F
and 50
LC016Valet card functionSC008 UCH type WITH/WITHOUT 4C, 4D, 4F and 50

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-67
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-67V9 MR-372-J84-87B000$215.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
UCH configurations (continued):
T.O*: Sunroof.Configuration
readingConfigurationName of
configurationChoice of
configurationVdiag
LC017Tyre Pressure Monitor
FunctionSC008 UCH typeWITH/WITHOUT44, 48, 4C, 4D, 4F
and 50
LC018Hazard warning lights
switched on by ABS CF024WITH/WITHOUT44, 48, 4C, 4D, 4F
and 50
LC019Rear screen wiper park
position controlAutomatic
configurationWITH/WITHOUT 44, 48, 4C, 4D
LC020Factory fitted perimeter

protection SC008 UCH typeWITH/WITHOUT 4C, 4D, 4F and 50
LC021Type of windscreen
SC008 UCH typeTINTED/HEAT
INSULATING44, 48, 4C, 4D, 4F
and 50
LC023 Engine type CF028F ENGINE/K
ENGINE/M
ENGINE44, 48, 4C, 4D, 4F
and 50
LC025See-me-home lighting CF032WITH/WITHOUT 44, 48, 4C, 4D
LC029 Selective door opening SC008 UCH typeWITH/WITHOUT44, 48, 4C, 4D, 4F
and 50
LC030Heating resistor type SC008 UCH typeNONE/1000 W/
1800 W 44, 48, 4C, 4D, 4F
and 50
LC035Child safety lockSC016 Child safety
lockWITH/WITHOUT 4C, 4D, 4F and 50
Automatic
configurationWITH/WITHOUT 44 and 48
LC041New vehicle storage modeVP016 ACTIVE/
INACTIVE 4F and 50
LC044 Rain/light sensor SC008 UCH typeWITH/WITHOUT 4F and 50
LC064 Rear screen wiper CF166 WITH/WITHOUT 4F and 50
LC070One-touch window(s)/
sunroof SC008 UCH typeWITH/WITHOUT 4F and 50
LC122Rear access aerialsCF224WITH/WITHOUT 50

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -135
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -135V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
LIGHTING FUNCTION
Sub-function: Lighting command
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-
functionParameter or
Status
checked Action Display and Notes Fault finding
Lighting
controlET081:Lighting switch
positionOFF
SIDE
DIPPED
MAIN BEAM HEADLIGHTS
HAZARD LIGHTS In the event of a fault,
refer to the
interpretation of status
ET081.
ET115:Request to switch
on lights by light
sensor PRESENT
ABSENTIn the event of a fault,
consult the
interpretation of status
ET115.
ET169:EngineSTOPPEDIn the event of a fault,
refer to the
interpretation of
status ET169.
ET113:Automatic lighting
button DEPRESSED
RELEASED In the event of a fault,
consult the
interpretation of
status ET113.
ET111:Front fog lights
requestPRESENT
ABSENT In the event of a fault,
consult the
interpretation of
status ET111.
ET082:Rear fog lights
requestPRESENT
ABSENT In the event of a fault,
consult the
interpretation of
status ET082.
ET085:Hazard warning
lights buttonDEPRESSED
RELEASED In the event of a fault,
refer to the
interpretation of
status ET085.
ET083:Left-hand indicator
requestPRESENT
ABSENT In the event of a fault,
refer to the
interpretation of
status ET083.
ET084:Right-hand indicator
requestPRESENT
ABSENT In the event of a fault,
refer to the
interpretation of
status ET084.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table
87B
87B -141
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table
87B
87B -141V9 MR-372-J84-87B000$430.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
*Trip computer: Not authorised
*Sunroof: Tool status Diagnostic tool title Vdiag
ET066Card detected button
V44, V48, V4C,
V4D, V4F, V50 ET067Card button press recognised
ET068Most recently locked by
ET069Most recently unlocked by
ET070Start button
ET071 Unprogrammed steering lock
ET072Steering lock
ET073Steering lock sensor signal
ET075+ Accessories present
ET077Wiper stalk position
ET078Windscreen washer request
ET079Rear screen washer request
ET080Rear screen wiper request
ET081Lighting switch position
ET082Rear fog lights request
ET083Left-hand indicator request
ET084Right-hand indicator request
ET085Hazard warning lights button
ET086Electric child safety lock V44, V48, V4C
ET087Sunroof*/one touch electric window authorisation
V44, V48, V4C,
V4D, V4F, V50 ET088Deadlocking activation source
ET090Deadlocking deactivation source
ET096Wiper stalk intermittent speed ring position
ET097Rear screen wiper park position
ET098ADAC* button
ET108Automatic gearbox lever position
ET109Reverse gear engaged
ET110UCH request to injection or Protection and Switching Unit
ET111Front fog lights request
ET112Interior lighting control