2008 RENAULT SCENIC wiring diagram

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 306
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 306V9 MR-372-J84-87B000$903.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP6NO DIPPED HEADLIGHTS
(Lights without xenon bulb)
NOTESOnly check this customer complaint after performing a complete check with the
diagnostic tool.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Check the bulbs.
Are the bulbs in good condition?
YES
Check the + 12 V supply between connections RPG
and MAS of component 270.
Check the + 12 V supply between connections RPD
and MAS of component 270.
If the connection or connections are faulty and there
is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
Are the feeds correct?
NO
Check status ET081 Lighting stalk position.
Is the dipped beam headlight request on dipped
beam?
YES
Run fault finding on the Protection and Switching
Unit and check the dipped headlight F8C fuses
(Vdiag 44 UPC) and F3 and F4 fuses (Vdiag 48 or
above UPC) on the UPC.
NOReplace the bulbs.
YESVerify that there is no corrosion on the
connector.
Repair if necessary.
NOApply interpretation of status ET081
Lighting stalk position.
AFTER REPAIRCarry out a complete check using the diagnostic tool.
UCH_V44_ALP6/UCH_V48_ALP6/ UCH_V4C_ALP6/
UCH_V4D_ALP6 /UCH_V4F_ALP6/UCH_V50_ALP6

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 307
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 307V9 MR-372-J84-87B000$903.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP7No main beam headlights
(Lights without xenon bulb)
NOTESOnly check this customer complaint after performing a complete check with the
diagnostic tool.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Check the bulbs.
Are the bulbs in good condition?
YES
Check the + 12 V supply on connection RPD of
component 226 and on connection RPG of
component 227.
Check for earth on connection MAS of
components 226 and 227.
If the connection or connections are faulty and there
is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
Are the feeds correct?
NO
Check status ET081 Lighting stalk position.
Does the side light request occur on main beam?
YES
Run fault finding on the Protection and Switching
Unit.
Check the F8A and F8B fuses (Vdiag 44 UPC) and
F6 and F7 fuses (Vdiag 48 or above UPC).
NOReplace the bulbs.
YESVerify that there is no corrosion on the
connector.
Repair if necessary.
NOApply interpretation of status ET081
Lighting stalk position.
AFTER REPAIRCarry out a complete check using the diagnostic tool.
UCH_V44_ALP7/UCH_V48_ALP7/ UCH_V4C_ALP7/
UCH_V4D_ALP7 /UCH_V4F_ALP7/UCH_V50_ALP7

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 309
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 309V9 MR-372-J84-87B000$903.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP9 No rear screen wiper
NOTESOnly check this customer complaint after performing a complete check with the
diagnostic tool.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Check status ET080 Rear screen wiper request
with the stalk in the rear screen wiper position.
Is status ET080 Present?
YES
Perform command AC007 Rear screen wiper.
Check for + 12 V on component 211 on the following
connection:
●Connection code 36C.
Check the earth of component 211 on the following
connection:
●Connection code MZ.
If the connection or connections are faulty and there
is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
Is the rear wiper working?
YES
Check the UCH connectors.
If the fault is still present, contact the Techline.
NOApply interpretation of status ET080 Rear
screen wiper request.
NOPerform fault finding on command AC007
Rear screen wiper.
AFTER REPAIRCarry out a complete check using the diagnostic tool.
UCH_V44_ALP9/UCH_V48_ALP9/ UCH_V4C_ALP9/
UCH_V4D_ALP9 /UCH_V4F_ALP9/UCH_V50_ALP9

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 312
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 312V9 MR-372-J84-87B000$903.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP12 No windscreen wiper
NOTESOnly check this customer complaint after performing a complete check with the
diagnostic tool.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Check the condition of the windscreen wiper motor connections (with battery disconnected) and the UPC
connections.
Check the condition of the connections and the absence of interference resistance on the following
connections:
●Connection code 14L.
●Connection code 14K.
●Connection code 14M between components 645 and 1337.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for an earth on connection MAS of component 212.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a complete check using the diagnostic tool.
UCH_V44_ALP12 /UCH_V48_ALP12/UCH_V4C_ALP12/
UCH_V4D_ALP12/UCH_V4F_ALP12/UCH_V50_ALP12

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 313
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 313V9 MR-372-J84-87B000$903.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP13 No front and rear screen washer
NOTESOnly check this customer complaint after performing a complete check with the
diagnostic tool.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Windscreen washer
Check status ET078 Front windscreen washer
request by moving the control stalk.
Is status ET078 present?
YES
Check for + 12 V between connections 16A and 24A
of component 677 (running).
Is there + 12 V?
YES
Check the hoses. If everything is OK.
Replace the washer fluid pump.
If the fault is still present, contact the Techline.
NOApply interpretation of status ET078 Front
windscreen washer request.
NOCheck the continuity and insulation of
connection 16A between components 677
and 1519.
Check the continuity and insulation of
connection 24A between components 677
and 1519.
If the connection or connections are faulty
and there is a repair procedure (see
Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a complete check using the diagnostic tool.
UCH_V44_ALP13 /UCH_V48_ALP13/UCH_V4C_ALP13/
UCH_V4D_ALP13/UCH_V4F_ALP13/UCH_V50_ALP13

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 316
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 316V9 MR-372-J84-87B000$903.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP15No passenger window operation
(Driver and passenger electric windows)
NOTESUse the Wiring Diagram Technical Note and a multimeter.
Only check this customer complaint after performing a complete check with the
diagnostic tool.
For vehicles with Mégane II phase 2 bodywork, see 87D Electric windows -
Sunroof, Fault finding chart.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Remove the passenger's window winder switch (see MR 364 (Mégane II) or MR 370 (Scenic II) Mechanical
systems, 87D, Electric windows - Sunroof, Front window winder switch on passenger's door: Removal -
Refitting) and disconnect its connector.
Check for + 12 V on connections 22A and MAN of component 133.
Are the feeds correct?
YES NO
Shunt connections 22D and 22A and
connections 22C and 22B of component 133 to
lower the window (to raise the window shunt
connections 22C and 22A and connections 22B and
MAN of component 133).
Does the window move?
YES NO
Replace the passenger's window
winder switch (see MR 364
(Mégane II) or MR 370 (Scenic II)
Mechanical systems, 87D,
Electric windows - Sunroof, Front
window winder switch on
passenger's door: Removal -
Refitting).
Remove the passenger's window winder switch
(see MR 364 (Mégane II) or MR 370 (Scenic II)
Mechanical systems, 87D, Electric windows -
Sunroof, Front window winder switch on
passenger's door: Removal - Refitting).
Shunt connection 21C with connections 22A and
22D of component 1512.
Check for + 12 V again on connections 22A and
MAN of components 133.
Are the feeds correct?
YES NO
Replace the driver's electric window
switch (see MR 364 (Mégane II) or
MR 370 (Scenic II) Mechanical
systems, 87D, Electric windows -
Sunroof, Front electric window
switch on driver's door: Removal
- Refitting).
AFTER REPAIRCarry out a complete check using the diagnostic tool.
UCH_V44_ALP15 /UCH_V48_ALP15/UCH_V4C_ALP15/
UCH_V4D_ALP15/UCH_V4F_ALP15/UCH_V50_ALP15

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 318
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 318V9 MR-372-J84-87B000$903.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP16No passenger window operation
(Driver and passenger one-touch electric windows)
NOTESUse the Wiring Diagram Technical Note and a multimeter.
Only check this customer complaint after performing a complete check with the
diagnostic tool.
For vehicles with Mégane II phase 2 bodywork, see 87D Electric windows -
Sunroof, Fault finding chart.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Remove the passenger's window winder switch (see MR 364 (Mégane II) or MR 370 (Scenic II) Mechanical
systems, 87D, Electric windows - Sunroof, Front window winder switch on passenger's door: Removal -
Refitting) and disconnect its connector.
Shunt connections 22A and MAN of component 133 to lower the window and to raise the window shunt
connections 22B and MAN of component 133.
Does the window move?
YES NO
Replace the passenger's window winder switch
(see MR 364 (Mégane II) or MR 370 (Scenic II)
Mechanical systems, 87D, Electric windows -
Sunroof, Front window winder switch on
passenger's door: Removal - Refitting).
Check that the right-hand dashboard cross member
earth is in good condition and correctly secured to
the chassis.
If the earth is not in good condition, clean and
retighten the terminal.
If the earth is faulty, replace the wiring.
Check the continuity of the following connection:
●Connection code BP70 between components 204 and 260.
Check the intermediate connectors and the fuse if there is a continuity or supply fault.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the
wiring.
Check for earth on connection MAN of
component 204.
Is the earth correct?
NO YES
Connect a voltmeter across
connections BP70 and MAN of
component 204.
Does the voltmeter display the
correct supply?
NO YES
AFTER REPAIRCarry out a complete check using the diagnostic tool.
UCH_V44_ALP16 /UCH_V48_ALP16/UCH_V4C_ALP16/
UCH_V4D_ALP16/UCH_V4F_ALP16/UCH_V50_ALP16

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 319
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 319V9 MR-372-J84-87B000$903.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP16
CONTINUED
NOTESUse the Wiring Diagram Technical Note and a multimeter.
Only check this customer complaint after performing a complete check with the
diagnostic tool.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Using a multimeter, check for + 12 V
between connections BP70 and 21K of
component 204.
Is the voltage approximately 12 V?
YES
Using a multimeter, check for + 12 V between
connections 22A and 22B of component 133.
Is the voltage approximately 12 V?
YES
Replace the window winder motor (see MR 365
(Mégane) or MR 371 (Scenic) Bodywork, 51A,
Side opening element mechanisms, Front side
door electric window lift mechanism: Removal -
Refitting).
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
NOCheck the continuity on the following
connection:
●Connection code 21K between
components 645 and 204.
If one continuity is poor, check the
intermediate connectors.
If the connector is faulty and if there is a
repair procedure (see Technical Note
6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair
the connector; otherwise, replace the
wiring.
NOCheck the continuity of the following
connections:
●Connection code 22A.
●Connection code 22B between
components 204 and 133.
Is the continuity of the connections
correct?
YES NO
AFTER REPAIRCarry out a complete check using the diagnostic tool.