2008 RENAULT SCENIC check gas supply

17C-13
MR-372-J84-17C000$177.mif
V2
17C
GAS INJECTION
Fault finding - Replacement of components
COMPUTER REPLACEMENT OR REPROGRAMMING PROCEDURE
The system can be programmed and reprogrammed via the diagnostic socket using the RENAULT CLIP diagnostic
tool (see Technical Note 3585A or follow the instructions provided by the diagnostic tool).
After reprogramming or replacing the computer:
–Switch the ignition off and then on again.
–Start and run the engine in LPG mode then stop the engine (to initialise the computer) and wait for
30 seconds.
–Switch on the ignition and use the diagnostic tool to carry out the following steps:
–use command VP001 Write VIN,
–after the injection has been reprogrammed, stored faults may appear on other computers. Clear the memories of
these computers,
–carry out a road test followed by another check with the diagnostic tool. IMPORTANT
–switch on the diagnostic tool (mains or cigarette lighter supply),
–connect a battery charger,
–shut down all the electrical consumers (lights, interior lights, air conditioning, radio CD, etc.),
–wait for the engine to cool down (coolant temperature below 60 °C and air temperature below 50 °C).
LPG 3000
Program No: AB
Vdiag No: 08/10
MR-372-J84-17C000$177.mif

17C-18
MR-372-J84-17C000$354.mif
V2
GAS INJECTION
Fault finding - Interpretation of faults
LPG 3000
Program No: AB
Vdiag No: 08/10
17C
DF013
PRESENT
OR
STOREDTANK SOLENOID VALVE CIRCUIT
CC.1: Short circuit to + 12 Volts
1.DEF: Non-compliance with emission control standards
IMPORTANT
When carrying out an operation on an LPG supply circuit component, consult the safety instructions
(see 17D, Gas injection, Introduction, Safety instructions for all operations).
NOTESPriority when dealing with a number of faults:
If fault DF021 LPG tank solenoid valve relay circuit or fault DF018 + After ignition
feed supply or fault DF016 Impact detected are present or stored, deal with these
faults first.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present after the engine is started and switched to LPG mode
or when command AC015 Tank solenoid valve is executed.
Manipulate the wiring harness between the gas computer and the gas tank solenoid valves in order to produce
a change in status (present ↔ stored).
Look for any damage to the wiring harness and check the connection and condition of the LPG tank solenoid
valves and their connections.
Repair if necessary.
Check the connection and condition of the LPG tank solenoid valve relay connector and its connections.
Replace the connector if necessary.
–check that the solenoid valve is supplied with +12V via track E3 of the LPG computer.
–check for + 12V on track D (for Mégane 2) or on track A (for Logan) of the LPG tank solenoid valve.
If necessary, check the insulation to earth and the continuity and absence of interference resistance on
the following connections:
For Mégane 2:
LPG tank solenoid valve track D
For Logan:
LPG tank solenoid valve track Atrack B5 of the LPG tank solenoid valve relay
track E3, LPG computer
track B5 of the LPG tank solenoid valve relay
track E3, LPG computer
If the fault is still present, check the intermediate connectors (R2 track 38, for Mégane 2), (R34 track 9,
for Logan).
Repair if necessary.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
GAZ3000_V08_DF013 / GAZ3000_V10_DF013

17C-20
MR-372-J84-17C000$354.mif
V2
GAS INJECTION
Fault finding - Interpretation of faults
LPG 3000
Program No: AB
Vdiag No: 08/10
17C
DF014
PRESENT
OR
STOREDGAUGE SUPPLY CIRCUIT
CC.0: Open circuit or short circuit to earth
CC.1: Short circuit to + 12 volts
NOTESSpecial note:
The system changes to forced petrol mode "LPG system fault" and refuses to change
to LPG mode while the fault is present.
Clear the faults from memory and then start the engine.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
GAZ3000_V08_DF014 / GAZ3000_V10_DF014

17C-21
MR-372-J84-17C000$354.mif
V2
GAS INJECTION
Fault finding - Interpretation of faults
LPG 3000
Program No: AB
Vdiag No: 08/10
17C
DF016
PRESENT
IMPACT DETECTED
1.DEF: Impact detected
2.DEF: Non-compliance with emission control standards
NOTESPriority when dealing with a number of faults:
If faults DF021 LPG tank solenoid valve relay circuit or fault DF018 + After ignition
feed supply are present or stored, deal with these faults first.
Special note:
As soon as the LPG computer receives this signal, engine operation is prohibited.
If the vehicle has been involved in an accident:
Carry out any necessary repairs,
–clear the fault,
–switch off the ignition,
–wait for the engine immobiliser indicator light to flash,
–switch on the ignition,
If the fault does not recur, end the fault finding procedure.
If the fault recurs, carry out fault finding on the AIRBAG computer.
If the vehicle has not been involved in an accident:
Check for + 12V on track 3 of the fuel pump cut-off relay and the LPG tank relay.
Repair if necessary.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
GAZ3000_V08_DF016P / GAZ3000_V10_DF016

17C-22
MR-372-J84-17C000$354.mif
V2
GAS INJECTION
Fault finding - Interpretation of faults
LPG 3000
Program No: AB
Vdiag No: 08/10
17C
DF017
PRESENT
OR
STOREDLPG LEAK DETECTION DOWNSTREAM OF THE EXPANSION
VALVE
1.DEF: Leak detection
2.DEF: Non-compliance with emission control standards
IMPORTANT
When carrying out an operation on an LPG supply circuit component, consult the safety instructions
(see 17D, Gas injection, Introduction, Safety instructions for all operations).
NOTESFault finding procedure application conditions:
–clear the faults,
–start the engine,
–select LPG mode,
–wait for the engine to operate in LPG mode with the status ET093 LPG mode
set to YES,
–turn the engine off,
–wait for 5 minutes,
–confirm that the fault is present.
Special note:
To detect the leak, use the product distributed by SODICAM, available under Part
number 77 11 143 071 (leak detector).
Start the engine and select LPG mode. Wait for the engine to operate in LPG mode with the status ET093 LPG
Mode set to YES and apply the leak detector product to:
–the expansion valve,
–the pipe between the expansion valve and the injector rail,
–the pipes between the injector rail and the injectors,
–the injector bodies.
Repair if necessary.
With the ignition on and the engine off, control the expansion valve solenoid valve using command
AC024 Expansion valve solenoid valve.
Without disconnecting the pipes, carefully remove:
–the LPG injector rail,
–the LPG injectors.
Apply the leak detector product to the injector seats.
Replace the faulty injector(s) (see MR 364 Mechanical, 17D, Gas injection, Injectors).
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
GAZ3000_V08_DF017 / GAZ3000_V10_DF017

17C-23
MR-372-J84-17C000$354.mif
V2
GAS INJECTION
Fault finding - Interpretation of faults
LPG 3000
Program No: AB
Vdiag No: 08/10
17C
DF018
PRESENT
OR
STORED+ AFTER IGNITION SUPPLY
CC.1: Short circuit to + 12 Volts
1.DEF: Abnormal voltage
2.DEF: Non-compliance with emission control standards
NOTESPriority when dealing with a number of faults:
If faults DF021 LPG tank solenoid valve relay circuit or fault DF016 Impact
detected are present or stored, deal with these faults first.
Special note:
To detect the leak, use the product distributed by SODICAM, available under
Part number 77 11 143 071 (leak detector).
Manipulate the wiring harness between the LPG computer and the after ignition feed supply circuit in order to
produce a change in status (present ↔ stored).
Look for any damage to the wiring harness and check the connection and condition of the after ignition feed
supply circuit and its connections.
If necessary, repair or replace the connector.
With the ignition on, check for + 12 volts on track C2 of the LPG computer.
Repair if necessary.
If the fault is still present, deal with the other faults, then proceed to the conformity check.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
GAZ3000_V08_DF018 / GAZ3000_V10_DF018

17C-31
MR-372-J84-17C000$354.mif
V2
GAS INJECTION
Fault finding - Interpretation of faults
LPG 3000
Program No: AB
Vdiag No: 08/10
17C
DF029
PRESENT
OR
STOREDLPG TANK SENDER SIGNAL VOLTAGE
CO.0: Open circuit or short circuit to earth
CO.1: Open circuit or short circuit to + 12V
CC.0: Short circuit to earth
1.DEF: Non-compliance with emission control standards
IMPORTANT
When carrying out an operation on an LPG supply circuit component, consult the safety instructions
(see 17D, Gas injection, Introduction, Safety instructions for all operations).
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after the engine has been started and switched to LPG
mode.
Manipulate the wiring harness between the LPG computer and the LPG tank sender in order to produce a change
in status (present ↔ stored).
Look for any damage to the wiring harness and check the connection and condition of the LPG tank sender
connector.
Replace the connector if necessary.
For Mégane II: Disconnect the connector from the LPG tank sender and measure the resistance between tracks
A and C (only for Mégane 2).
Replace the sender if the resistance value is different to the value shown in the table below (only for Mégane 2).
Check for the presence of earth on track C (for Mégane 2) or track A3 (for Logan) of the LPG tank sender
connector.
Repair if necessary.
Check the insulation in relation to earth and the continuity and the absence of interference resistance on
the connection between:
For Mégane 2:
LPG computer track B1
For Logan:
LPG computer track D4track B, of the LPG tank sender
track A2, of the LPG tank sender
If the fault is still present, check the intermediate connectors (R2 track 36, for Mégane 2), (R34 track 8 and R345
track B, for Logan).
Repair if necessary.
If the fault is still present, deal with the other faults, then proceed to the conformity check.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
GAZ3000_V08_DF029 / GAZ3000_V10_DF029

17C-33
MR-372-J84-17C000$354.mif
V2
GAS INJECTION
Fault finding - Interpretation of faults
LPG 3000
Program No: AB
Vdiag No: 08/10
17C
DF030
PRESENT
OR
STOREDLPG TANK SENDER SUPPLY VOLTAGE
1.DEF: Voltage outside permitted range of values
2.DEF: Non-compliance with emission control standards
IMPORTANT
When carrying out an operation on an LPG supply circuit component, consult the safety instructions
(see 17D, Gas injection, Introduction, Safety instructions for all operations).
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after the engine has been started and switched to LPG
mode.
Manipulate the wiring harness between the LPG computer and the LPG tank sender in order to produce a change
in status (present ↔ stored).
Look for any damage to the wiring harness and check the connection and condition of the LPG tank sender
connector.
Replace the connector if necessary.
Check for a supply on track A4 (for Mégane 2) or on track B2 (for Logan) of the LPG computer and on track A
(for Mégane 2) or on track A2 (for Logan) of the fuel sender during LPG operation.
For Mégane 2: check the intermediate connectors R2 track 39, R34 track 15 and R345 track A.
Contact the Techline if the voltage value is not between 4.6V and 5.2V.
Check the insulation and continuity of the following connection:
For Mégane 2:
LPG computer track D3
For Logan:
LPG computer track D3track C of the LPG tank sender
track A1 of the LPG tank sender unit
If the fault is still present, check the intermediate connectors (R2 track 37, for Mégane 2, R674 track 4,
for Logan) and (R34 track 16 and R345 track C, for Mégane 2).
Repair if necessary.
If the fault is still present, deal with the other faults, then proceed to the conformity check.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
GAZ3000_V08_DF030 / GAZ3000_V10_DF030