2008 RENAULT SCENIC fuse

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Introduction87G
87G - 3V7 MR-372-J84-87G050$055.mif
UPC
Vdiag No.: 48, 4C
3. REMINDER
PROCEDURE
To run fault finding on the vehicle's computers, switch on the ignition in fault finding mode (forced + after ignition
feed). Run the self-test procedure for the UPC internal relays and fuses using AC016 Electrical supply circuit
test.
Depending on the type of vehicle equipment, proceed as follows:
To cut off the + after ignition feed, proceed as follows:
Faults
Faults are declared as either present or stored (depending on whether they appeared in a certain context and have
disappeared since, or whether they remain present but have not been diagnosed within the current context).
The present or stored status of faults should be taken into consideration when the diagnostic tool is used following
the + after ignition supply being switched on (without operating the system components).
For a present fault, apply the procedure described in the Interpretation of faults section.
For a stored fault, note the faults displayed and apply the instructions in the Notes section.
If the fault is confirmed when the instructions in the Notes section are applied, the fault is present. Deal with the fault
If the fault is not confirmed, check:
–the electrical lines which correspond to the fault,
–the connectors on these lines (corrosion, bent pins, etc.),
–the resistance of the component detected as faulty,
–the condition of the wires (melted or split insulation, wear). WARNING
Switch off all unnecessary consumers:
–Radio navigation system.
–Switch the passenger compartment ventilation speed to 0.
–Switch off the interior lights (forced off).
With the vehicle card in the card reader, press and hold the start button (+ 5 seconds) outside starting conditions,
connect the diagnostic tool and carry out the required operations.
Press the start button twice briefly (less than 3 seconds); check that the + after ignition feed has cut (computer
indicator lights on the instrument panel go out).

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Introduction87G
87G - 6V7 MR-372-J84-87G050$055.mif
UPC
Vdiag No.: 48, 4C
4. FAULT FINDING PROCEDURE (continued)
Wiring check
Fault finding problems
Disconnecting the connectors and/or manipulating the wiring harness may temporarily remove the cause of a fault.
Electrical measurements of voltage, resistance and insulation are generally correct, especially if the fault is not
present when the analysis is made (stored fault).
Visual inspection
Look for damage under the bonnet and in the passenger compartment.
Carefully check the fuses, insulators and wiring harness routing.
Look for signs of oxidation.
Tactile inspection
While manipulating the wiring harness, use the diagnostic tool to note any change in fault status from stored to
present.
Make sure that the connectors are properly locked.
Apply light pressure to the connectors.
Twist the wiring harness.
If there is a change in status, try to locate the source of the fault.
Inspection of each component
Disconnect the connectors and check the appearance of the clips and tabs, as well as the crimping (no crimping on
the insulating section).
Make sure that the clips and tabs are properly locked in the sockets.
Check that no clips or tabs have been dislodged during connection.
Check the clip contact pressure using an appropriate model of tab.
Continuity, insulation and resistance check
Check the continuity of entire lines, then section by section.
Look for a short circuit to earth, to + 12 V or to another wire.
If a fault is detected, repair or replace the wiring harness.

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - System operation87G
87G-12V7 MR-372-J84-87G050$110.mif
UPC
Vdiag No.: 48, 4C
9 - Injection
The Protection and Switching Unit is involved in injection operation, relating to supplying the computer and its
sensors.
Supply malfunctions may lead to engine management customer complaints (rough idle, etc.).
10 - Fuse fault finding
The Protection and Switching Unit can detect the condition of its fuses and indicate faults using:
DF014 LEFT-HAND SIDE LIGHT CIRCUIT.
DF015 RIGHT-HAND SIDE LIGHT CIRCUIT.
DF016 LEFT-HAND DIPPED HEADLIGHT CIRCUIT.
DF017 RIGHT-HAND DIPPED HEADLIGHT CIRCUIT.
DF018 LEFT-HAND MAIN BEAM HEADLIGHT CIRCUIT.
DF019 RIGHT-HAND MAIN BEAM HEADLIGHT CIRCUIT.
DF020 FRONT FOG LIGHT CIRCUIT.
DF021 REVERSING LIGHT(S) CIRCUIT.
DF022 REAR SCREEN DE-ICER CIRCUIT.
DF023 FRONT WINDSCREEN WIPER CIRCUIT.
DF024 GAS COMPUTER SUPPLY.
DF025 AIRBAG/ELECTRIC POWER-ASSISTED STEERING SUPPLY.
DF026 AUTOMATIC TRANSMISSION SUPPLY.
DF029 STEERING COLUMN LOC/ENGINE MANAGEMENT SUPPLY.
DF030 AIR CONDITIONING COMPRESSOR SUPPLY CIRCUIT.
DF031 HEADLIGHT WASHERS SUPPLY CIRCUIT.
DF032 + 12 V RELAY SUPPLY CIRCUIT.
DF036 STEERING COLUMN LOCK SUPPLY CIRCUIT.
To carry out fault finding on the fuses, run command AC016 Test electrical supply circuits.
If a fuse is faulty, the associated fault becomes STORED.
Once the fuse has been replaced or the repair completed, run command AC016 Test electrical supply circuits
again to clear the fault.
Protection and Switching Unit Version
There are 4 Protection and Switching Unit versions:
–N1: vehicle with a 340 W fan assembly.
–N2: vehicle with a 460 W fan assembly.
–N3: vehicle with a 550 W fan assembly (external relay).
–N4: vehicle with 340 W, 460 W or 550 W fan assemblies + automatic transmission and/or LPG and/or with
headlight washers.

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults87G
87G-23V7 MR-372-J84-87G050$330.mif
UPC
Vdiag No.: 4C
DF009
CONTINUED
Check the connection and condition of the passenger compartment fuse and relay box, the gear lever display,
the steering column top control module, the additional heater relay 1 and 2, the diagnostic socket, the
parking distance control ECU, the right and left-hand rear electric window switch, the radio, the electric
door mirror control, the front and rear electric window locking controls and the passenger electric window
switch, component codes 260, 1129, 1546, 1067, 1068, 225, 1222, 130, 131, 261, 134, 135, 1511, 1512
and 133.
Check for a voltage on connection AP43 to the connectors for the passenger compartment fuse and relay box,
the gear lever display, the steering column top control module, the additional heater relay 1 and 2, the
diagnostic socket, the parking distance control ECU, the right and left-hand rear electric window switch,
the radio, the electric door mirror control, the front and rear electric window locking controls, the
passenger electric window switch, component codes 260, 1129, 1546, 1067, 1068, 225, 1222, 130, 131, 261,
134, 135, 1511, 1512 and 133.
If the connection or connections are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–AP31 between components 1337 and 997,
–AP11 between components 1337, 485, 155 and 1109,
–APCB between components 1337 and 645,
–AP15 between components 1337 and 1088,
–AP44 between components 1337, 756 and 1232,
–AP43 between components 1337, 260, 1129, 1546, 1067, 1068, 225, 1222, 130, 131, 261, 134, 135, 1511, 1512
and 133.
If the connections are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the connection and condition of the Protection and Switching Unit, component code 1337.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
If the fault is still present, contact the Techline.
AFTER REPAIRErase the faults from the computer memory, switch the + after ignition supply off and
back on again and run another check using the diagnostic tool.

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults87G
87G-27V7 MR-372-J84-87G050$330.mif
UPC
Vdiag No.: 48, 4C
DF014
CONTINUED
CC.0
NOTESSpecial note:
To display this fault as present or stored, run the command
AC016 Electrical supply circuit test.
Use Wiring Diagrams Technical Note for Mégane II or
Scénic II.
Check the conformity of the fuse F1 (7.5A) for the Protection and Switching Unit, component code 1337.
Check the insulation, continuity and the absence of interference resistance on the following connection:
–MAS between components 1337 and 227.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRRun command AC016 "Electrical supply circuits test".
Erase the faults from the computer memory, switch the + after ignition supply off and
back on again and run another check using the diagnostic tool.

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults87G
87G-29V7 MR-372-J84-87G050$330.mif
UPC
Vdiag No.: 48, 4C
DF015
CONTINUED
CC.0
NOTESSpecial note:
To display this fault as present or stored, run the command
AC016 Electrical supply circuit test.
Use Wiring Diagrams Technical Note for Mégane II or
Scénic II.
Check the conformity of the fuse F2 (7.5A) for the Protection and Switching Unit, connection code 1337.
Check the insulation, continuity and the absence of interference resistance on the following connection:
–MAS between components 1337 and 226.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRRun command AC016 "Electrical supply circuits test".
Erase the faults from the computer memory, switch the + after ignition supply off and
back on again and run another check using the diagnostic tool.

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults87G
87G-31V7 MR-372-J84-87G050$330.mif
UPC
Vdiag No.: 48, 4C
DF016
CONTINUED
CC.0
NOTESSpecial note:
To display this fault as present or stored, run the command
AC016 Electrical supply circuit test.
Use Wiring Diagrams Technical Note for Mégane II or
Scénic II.
Check the conformity of the fuse F4 (10A) for the Protection and Switching Unit.
Check the insulation, continuity and the absence of interference resistance on the following connection:
–CPG between components 1337 and 227.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRRun command AC016 "Electrical supply circuits test".
Erase the faults from the computer memory, switch the + after ignition supply off and
back on again and run another check using the diagnostic tool.

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults87G
87G-33V7 MR-372-J84-87G050$330.mif
UPC
Vdiag No.: 48, 4C
DF017
CONTINUED
CC.0
NOTESSpecial note:
To display this fault as present or stored, run the command
AC016 Electrical supply circuit test.
Use Wiring Diagrams Technical Note for Mégane II or
Scénic II.
Check the conformity of the fuse F3 (10A) for the Protection and Switching Unit.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–CPD between components 1337 and 226.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRRun command AC016 "Electrical supply circuits test".
Erase the faults from the computer memory, switch the + after ignition supply off and
back on again and run another check using the diagnostic tool.