2008 RENAULT SCENIC bulb

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87G
87G - 76V7 MR-372-J84-87G050$770.mif
UPC
Vdiag No.: 48, 4C ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands
AC001
MAIN BEAM HEADLIGHTS
NOTESSpecial notes:
Check the condition and connections of fuses 6 (10A) and 7 (10A) on the Protection
and Switching Unit. Replace them if necessary.
Check the condition and connections of the bulbs. Replace them if necessary.
Use Wiring Diagrams Technical Note for Mégane II or Scénic II.
Check the condition and connection of the headlights, component codes 226 and 227 (tabs bent, broken or
oxidised).
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check for earth, connection code MAS for the headlights, component codes 226 and 227.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for + 12 V on headlight connection codes RPD and RPG whilst running the command.
If the connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the condition and connection of the Protection and Switching Unit 8-track AN connector, connection
code 1337 (tabs broken, bent or oxidised).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–RPD, between components 1337 and 226,
–RPG between components 1337 and 227.
If the connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIRRepeat the conformity check from the start.
MR-372-J84-87G050$770.mif

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87G
87G - 77V7 MR-372-J84-87G050$770.mif
UPC
Vdiag No.: 48, 4C
AC002
DIPPED HEADLIGHTS
NOTESSpecial notes:
Check the condition and connections of fuses 3 (10A) and 4 (10A) on the Protection
and Switching Unit. Replace them if necessary.
Check the condition and connections of the bulbs. Replace them if necessary.
Use Wiring Diagrams Technical Note for Mégane II or Scénic II.
Check the condition and connection of the headlights, component codes 226 and 227 (tabs bent, broken or
oxidised).
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check for earth, connection code MAS for the headlights, component codes 226 and 227.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for + 12 V on headlight connection codes CPD and CPG whilst running the command.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the condition and connection of the Protection and Switching Unit 8-track AN connector, connection
code 1337 (tabs broken, bent or oxidised).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–CPD, between components 1337 and 226,
–CPG between components 1337 and 227.
If the connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIRRepeat the conformity check from the start.

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87G
87G - 78V7 MR-372-J84-87G050$770.mif
UPC
Vdiag No.: 48, 4C
AC003
SIDE LIGHTS
NOTESSpecial notes:
Check the condition and connections of fuses 1 (7.5A) and 2 (7.5A) on the Protection
and Switching Unit. Replace them if necessary.
Check the condition and connections of the bulbs. Replace them if necessary.
Use Wiring Diagrams Technical Note for Mégane II or Scénic II.
Check the condition and connection of the headlights, component codes 226 and 227 (tabs bent, broken or
oxidised).
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check for earth, connection code MAS for the headlights, component codes 226 and 227.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for + 12 V on side light connection codes LPD and LPG whilst running the command.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the condition and connection of the Protection and Switching Unit 8-track AN connector, connection
code 1337 (tabs broken, bent or oxidised).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–LPD, between components 1337 and 226,
–LPG, between components 1337 and 227.
If the connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIRRepeat the conformity check from the start.

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87G
87G - 79V7 MR-372-J84-87G050$770.mif
UPC
Vdiag No.: 48, 4C
AC004
FRONT FOG LIGHTS
NOTESSpecial notes:
Use this command only for vehicles fitted with front fog lights.
Check the condition and connection of fuse 5 (20A) on the Protection and Switching
Unit. Replace it if necessary.
Check the condition and connection of the bulbs. Replace them if necessary.
Use Wiring Diagrams Technical Note for Mégane II or Scénic II.
Check the condition and connection of the fog lights, component codes 176 and 177 (tabs bent, broken or
oxidised).
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check for earth connection code MAS on the headlights, component codes 176 and 177.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for + 12 V on connection codes 8E and 8F for the fog lights whilst running the command.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the condition and connection of the Protection and Switching Unit 8-track AN connector, connection
code 1337 (tabs broken, bent or oxidised).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–8E, between components 1337 and 177,
–8F, between components 1337 and 176.
If the connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIRRepeat the conformity check from the start.