2008 RENAULT SCENIC air condition

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults87G
87G-22V7 MR-372-J84-87G050$330.mif
UPC
Vdiag No.: 4C
DF009
PRESENT
OR
STORED+ APC CIRCUIT
1.DEF: Permanent low level
2.DEF: Permanent high signal
NOTESSpecial note:
This fault only applies to Vdiag 4C.
Conditions for applying the fault finding procedure to present faults:
The fault is declared present after the ignition has been switched on.
Use Wiring Diagrams Technical Note for Mégane II or Scénic II.
Check the connection and condition of the LPG electric control unit connector, component code 997.
Check for a voltage on connection AP31 to the connector for the LPG electric control unit, component code 997.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the connection and condition of the multifunction switch, the reverse gear switch and the manual
gearbox neutral sensor/reversing lights, component codes 485, 155, and 1109.
Check for a voltage on connection AP11 to the connectors for the multifunction switch, the reverse gear switch
and the manual gearbox neutral sensor/reverse lights, component codes 485, 155, and 1109.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the connection and condition of the passenger compartment electric control unit, component code 645.
Check for a voltage on connection APCB to the connector for the passenger compartment electric control unit,
component code 645.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the connection and condition of the electric steering column lock, component code 1088.
Check for a voltage on connection AP15 to the connector for the electric steering column lock, component code
1088.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the connection and condition of the airbag/pretensioner electric control unit and the electric power-
assisted steering system, component codes 756 and 1232.
Check for a voltage on connection AP44 to the connectors for the airbag/pretensioner electric control unit and
the electric power-assisted steering system connectors, component codes 756 and 1232.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
AFTER REPAIRErase the faults from the computer memory, switch the + after ignition supply off and
back on again and run another check using the diagnostic tool.
USM_V4C_DF009

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults87G
87G-23V7 MR-372-J84-87G050$330.mif
UPC
Vdiag No.: 4C
DF009
CONTINUED
Check the connection and condition of the passenger compartment fuse and relay box, the gear lever display,
the steering column top control module, the additional heater relay 1 and 2, the diagnostic socket, the
parking distance control ECU, the right and left-hand rear electric window switch, the radio, the electric
door mirror control, the front and rear electric window locking controls and the passenger electric window
switch, component codes 260, 1129, 1546, 1067, 1068, 225, 1222, 130, 131, 261, 134, 135, 1511, 1512
and 133.
Check for a voltage on connection AP43 to the connectors for the passenger compartment fuse and relay box,
the gear lever display, the steering column top control module, the additional heater relay 1 and 2, the
diagnostic socket, the parking distance control ECU, the right and left-hand rear electric window switch,
the radio, the electric door mirror control, the front and rear electric window locking controls, the
passenger electric window switch, component codes 260, 1129, 1546, 1067, 1068, 225, 1222, 130, 131, 261,
134, 135, 1511, 1512 and 133.
If the connection or connections are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–AP31 between components 1337 and 997,
–AP11 between components 1337, 485, 155 and 1109,
–APCB between components 1337 and 645,
–AP15 between components 1337 and 1088,
–AP44 between components 1337, 756 and 1232,
–AP43 between components 1337, 260, 1129, 1546, 1067, 1068, 225, 1222, 130, 131, 261, 134, 135, 1511, 1512
and 133.
If the connections are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the connection and condition of the Protection and Switching Unit, component code 1337.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
If the fault is still present, contact the Techline.
AFTER REPAIRErase the faults from the computer memory, switch the + after ignition supply off and
back on again and run another check using the diagnostic tool.

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults87G
87G-24V7 MR-372-J84-87G050$330.mif
UPC
Vdiag No.: 48, 4C
DF012
PRESENT
OR
STOREDALTERNATOR
1.DEF: Alternator mechanical or electrical fault
NOTESConditions for applying the fault finding procedure to present faults:
The fault is declared present after the engine has been running for at least 1 minute.
Special note:
The fault illuminates the Battery and STOP warning lights on the instrument panel.
Use Wiring Diagrams Technical Note for Mégane II or Scénic II.
1.DEF
NOTESNone.
Check the fitting, condition and tension of the accessories drive belt.
Visually check that the alternator is not clogged.
Clean out the alternator cooling vents using an air gun.
Check the wiring, the connections and the earths (see Test no. 1 Wiring test).
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Run command AC014 Alternator regulation (see Interpretation of commands).
With the bonnet closed, start the engine.
Leave the engine to run for 2 minutes at idle speed.
If the fault is still present, replace the alternator (see MR 364 or MR 370 Mechanical, 16A, Starting - Charging,
Alternator: Removal - Refitting).
AFTER REPAIRErase the faults from the computer memory, switch the + after ignition supply off and
back on again and run another check using the diagnostic tool.
USM_V48_DF012/USM_V4C_DF012

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults87G
87G-25V7 MR-372-J84-87G050$330.mif
UPC
Vdiag No.: 48, 4C
DF013
PRESENT
OR
STOREDVOLTAGE REGULATION
1.DEF: Voltage too low
2.DEF: Voltage too high
NOTESSpecial note:
Deal with the faults DF012 Alternator and DF007 UPC - alternator connection first
if they are present or stored.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present with the engine running.
Use Wiring Diagrams Technical Note for Mégane II or Scénic II.
Check the conformity of the wiring (see Test no. 2 Wiring test).
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the conformity of the parameter PR004 Battery voltage (see Interpretation of parameters).
If the fault is still present, contact the Techline.
AFTER REPAIRErase the faults from the computer memory, switch the + after ignition supply off and
back on again and run another check using the diagnostic tool.
USM_V48_DF013/USM_V4C_DF013

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults87G
87G-26V7 MR-372-J84-87G050$330.mif
UPC
Vdiag No.: 48, 4C
DF014
PRESENT
OR
STOREDLEFT-HAND SIDE LIGHT CIRCUIT
CO: Open circuit
CC.0: Short circuit to earth
CO
NOTESSpecial note:
To display this fault as present or stored, run the command
AC016 Electrical supply circuit test.
Use Wiring Diagrams Technical Note for Mégane II or
Scénic II.
Check that the front left-hand side light bulb is sound.
Repair if necessary.
Check the condition and connection of the connector to the left-hand headlight, component code 227 (tabs bent,
broken, oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check that the earth connection code MAS, for the left-hand headlight connector is perfect.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the condition and connection of the Protection and Switching Unit 8-track connector AN (tabs broken, bent
or oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check the insulation, continuity and the absence of interference resistance on the following connection:
–LPG between components 1337 and 227.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the fitting and switch on the left-hand headlight.
Repair if necessary or replace the light if it is faulty.
If the fault is still present, contact the Techline.
AFTER REPAIRRun command AC016 "Electrical supply circuits test".
Erase the faults from the computer memory, switch the + after ignition supply off and
back on again and run another check using the diagnostic tool.
USM_V48_DF014/USM_V4C_DF014

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults87G
87G-28V7 MR-372-J84-87G050$330.mif
UPC
Vdiag No.: 48, 4C
DF015
PRESENT
OR
STOREDRIGHT-HAND SIDE LIGHT CIRCUIT
CO: Open circuit
CC.0: Short circuit to earth
CO
NOTESSpecial note:
To display this fault as present or stored, run the command
AC016 Electrical supply circuit test.
Use Wiring Diagrams Technical Note for Mégane II or
Scénic II.
Check that the front right-hand side light bulb is sound.
Repair if necessary.
Check the condition and connection of the right-hand headlight, component code 226 (tabs broken, bent or
oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check that the earth connection code MAS for the right-hand headlight connector, component code 226 is
perfect.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the condition and connection of the Protection and Switching Unit 8-track AN connector, component code
1337 (tabs broken, bent or oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check the insulation, continuity and the absence of interference resistance on the following connection:
–LPD, between components 1337 and 226.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the fitting and switch on the right-hand headlight.
Repair if necessary or replace the light if it is faulty.
If the fault is still present, contact the Techline.
AFTER REPAIRRun command AC016 "Electrical supply circuits test".
Erase the faults from the computer memory, switch the + after ignition supply off and
back on again and run another check using the diagnostic tool.
USM_V48_DF015/USM_V4C_DF015

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults87G
87G-30V7 MR-372-J84-87G050$330.mif
UPC
Vdiag No.: 48, 4C
DF016
PRESENT
OR
STOREDLEFT-HAND DIPPED HEADLIGHT CIRCUIT
CO: Open circuit
CC.0: Short circuit to earth
CO
NOTESSpecial note:
To display this fault as present or stored, run the command
AC016 Electrical supply circuit test.
Use Wiring Diagrams Technical Note for Mégane II or
Scénic II.
Check that the left-hand dipped beam headlight bulb is sound.
Repair if necessary.
Check the condition and connection of the connector for the left-hand headlight, component code 227
(tabs bent, broken, oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check that the earth, connection code MAS for the left-hand headlight connector, component code 227 is
perfect.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the condition and connection of the 8-track connector AN for the Protection and Switching Unit,
component code 1337 (tabs bent, broken, oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check the insulation, continuity and the absence of interference resistance on the following connection:
–CPG between components 1337 and 227.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the fitting and switch on the left-hand headlight.
Repair if necessary or replace the light if it is faulty.
If the fault is still present, contact the Techline.
AFTER REPAIRRun command AC016 "Electrical supply circuits test".
Erase the faults from the computer memory, switch the + after ignition supply off and
back on again and run another check using the diagnostic tool.
USM_V48_DF016/USM_V4C_DF016

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults87G
87G-32V7 MR-372-J84-87G050$330.mif
UPC
Vdiag No.: 48, 4C
DF017
PRESENT
OR
STOREDRIGHT-HAND DIPPED HEADLIGHT CIRCUIT
CO: Open circuit
CC.0: Short circuit to earth
CO
NOTESSpecial note:
To display this fault as present or stored, run the command
AC016 Electrical supply circuit test.
Use Wiring Diagrams Technical Note for Mégane II or
Scénic II.
Check that the right-hand dipped beam headlight bulb is sound.
Repair if necessary.
Check the condition and connection of the connector for the right-hand headlight, component code 226
(tabs bent, broken, oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check that the earth on connection code MAS for the right-hand headlight, component code 226 is perfect.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the condition and connection of the 8-track connector AN for the Protection and Switching Unit,
component code 1337 (tabs bent, broken, oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check the insulation, continuity and the absence of interference resistance on the following connection:
–CPD between components 1337 and 226.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the fitting and switch on the right-hand headlight.
Repair if necessary or replace the light if it is faulty.
If the fault is still present, contact the Techline.
AFTER REPAIRRun command AC016 "Electrical supply circuits test".
Erase the faults from the computer memory, switch the + after ignition supply off and
back on again and run another check using the diagnostic tool.
USM_V48_DF017/USM_V4C_DF017