2008 PONTIAC VIBE ECO mode

Automatic Dimming Rearview Mirror
While sitting in a comfortable driving position, adjust
the mirror so you can see clearly behind your vehicle.
Hold the mirror in the center to move it up or down
and side to side.
The mirror may have an automatic dimming feature that
darkens gradually to reduce the glare of headlamps from
behind. When the ignition key is inserted and turned
on, the inside rear view mirror always turns on in the
automatic function mode.An indicator light located on
the mirror will come on to show you that the function
is on. When the inside air temperature is low, it may take
a little longer for the mirror to darken in response to the
detection of headlights.
Press the AUTO button located in the lower center of
the mirror to turn automatic dimming on and the
((off)
button located next to the AUTO button to turn automatic
dimming off.
One photocell on the front of the mirror senses when it
is becoming dark outside. Another photocell, facing
rearward, senses headlamps behind you.
To keep the photocells operating well, occasionally
clean them with a cotton swab and glass cleaner.
Outside Remote Control Mirrors
Your vehicle has outside power adjustable mirrors.
The controls are located
to the left of the steering
wheel on the instrument
panel.
To adjust either mirror, push the button labeled L (left) or
R (right). Use the arrows on the control pad to adjust the
direction of the mirror. Once both mirrors have been
adjusted, move the selector switch back to the center.
This prevents the mirrors from being moved once they
have been adjusted.
2-34

Push the RCL button while in XM™ mode (if equipped)
to retrieve four different categories of information
related to the current song or channel: Artist, Song Title,
Category or PTY, Channel Number/Channel Name.
To change the default on the display, push the RCL
button until the desired option displays, then hold the
button until the display ashes. The selected display
becomes the default.
Finding a Station
BAND:Press this button to switch between FM1, FM2,
AM, or XM1 or XM2 (if equipped). The display shows
the selection.
AM/FM:For the Radio with Six-Disc CD player, press
this button to switch between FM1, FM2, AM, XM1,
and XM2 (if equipped). The selection displays.
TUNE:Turn this knob to select radio stations.
wxorstSEEK:Press the up or the down
arrows to go to the next or to the previous station and
stay there.
The radio only seeks stations with a strong signal that
are in the selected band.
wxorstSCAN:Press and hold either SCAN
arrow for two seconds until SCAN or SC displays and a
beep sounds. The radio goes to a station, plays for a
few seconds, then goes to the next station. Press either
SCAN arrows again to stop scanning.To scan preset stations, press and hold either SCAN
arrow for more than four seconds until PSCAN or
PRESET SCAN and the preset number displays and a
double beep sounds. The radio goes to the rst preset
station, plays for a few seconds, then goes to the next
preset station. Press either SCAN arrow again to stop
scanning presets.
The radio scans stations only with a strong signal that are
in the selected band.
Setting Preset Stations
Up to 30 stations (six FM1, six FM2, six AM, six XM1,
and six XM2 (if equipped)), can be programmed on
the six numbered pushbuttons, by performing the
following steps:
1. Turn the radio on.
2. Press BAND or depending on the radio, AM/FM, to
select FM1, FM2, AM, XM1, and XM2 (if equipped).
3. Tune in the desired station.
4. Press and hold one of the six numbered
pushbuttons until a beep sounds. When that
numbered pushbutton is pressed, the station
that was set, returns and the equalization that
was selected is stored for that pushbutton.
5. Repeat the steps for each pushbutton.
3-46

AUTO EQ (Automatic Equalization):For the Radio
with Six-Disc CD player, press this button to select
customized equalization settings designed for country,
jazz, talk, pop, rock, and classical.
To return to the manual mode, press the AUTO EQ
button until CUSTOM displays. Then manually adjust
the bass, midrange, and treble using the AUDIO knob.
Adjusting the Speakers (Balance/Fade)
BAL (Balance):To adjust the balance between the right
and the left speakers, press and release this button until
BAL displays. The SELECT LED indicator lights to show
that the speakers can be adjusted. Turn the SELECT
knob to move the sound toward the right or the left
speakers.
FADE:Press and release this button until FADE
displays, to adjust the fade between the front and the
rear speakers. The SELECT LED indicator lights to
show that the speakers can be adjusted. Turn the
SELECT knob to move the sound toward the front
or the rear speakers.Press and hold the BAL FADE button for two seconds
to return all speaker settings to the middle position.
For vehicles that have a radio with a Six-Disc CD player,
see the following for adjusting the speakers.
AUDIO:For the Radio with Six-Disc CD player, push
and release the AUDIO knob until BAL (balance)
displays, to adjust the balance between the right and
the left speakers. Turn the knob to move the sound
toward the right or the left speakers.
Push and release the AUDIO knob until FAD (fade)
displays, to adjust the fade between the front and rear
speakers. Turn the knob to move the sound toward
the front or the rear speakers.
Select balance or fade and push and hold the AUDIO
knob, to adjust the balance and the fade to the middle
position. The radio beeps once and adjusts the display
level to the middle position.
Push and hold the AUDIO knob when no tone or speaker
controls display, to adjust all tone and speaker controls
to the middle position. CENTERED displays and a beep
sounds.
3-48

Finding a Program Type (PTY)
Station (RDS and XM™)
To select and nd a desired PTY perform the following:
1. Press PROG TYPE, or depending on the radio,
P-TYPE, to activate program type select mode.
The PTY symbol displays.
2. Turn the SELECT, or depending on the radio,
P-TYPE, knob to select a PTY.
3. Once the desired PTY displays, press either SEEK
arrow to select the PTY and to take you to the
PTY’s rst station.
4. To go to another station within that PTY, and the
PTY displays, press either SEEK arrow once. If the
PTY is not displayed, press either SEEK arrow twice
to display the PTY and then to go to another station.
5. Press PROG TYPE, or depending on the radio,
P-TYPE, to exit program type select mode.
If PTY times out and is no longer on the display,
go back to Step 1.
If both PTY and TRAF are on, the radio searches
for stations with the selected PTY and traffic
announcements.
The Radio with Six-Disc CD player has the PTY
interrupt feature. To use this feature, press and hold the
P-TYPE button until a beep sounds on the PTY you
want to interrupt with. When selected, an asteriskdisplays beside that PTY on the display. Select multiple
interrupts if desired. When listening to a CD, the last
selected RDS station interrupts play if that selected
program type format is broadcast.
wxorstSCAN:Scan the stations within a PTY
by performing the following:
1. Press PROG TYPE, or depending on the radio,
P-TYPE, to activate program type select mode.
The PTY symbol displays.
2. Turn the SELECT, or depending on the radio,
P-TYPE, knob to select a PTY.
3. Once the desired PTY is displayed, press and hold
either SCAN arrow, and the radio begins scanning
the stations in the PTY.
4. Press either SCAN arrow to stop at a station.
If both PTY and TRAF are on, the radio scans for stations
with the selected PTY and traffic announcements.
BAND or AM/FM (Alternate Frequency):Alternate
frequency lets the radio switch to a stronger FM station
with the same program type. To turn alternate frequency
on, press and hold BAND or depending on the radio, A/M
for two seconds. AF ON displays. The radio can switch to
FM stations with a stronger frequency.
To turn alternate frequency off, press and hold BAND
again for two seconds. A F OFF displays. The radio does
not switch to stronger FM stations.
3-49

Setting Preset PTYs (RDS Only)
These pushbuttons have factory PTY presets. Up to
12 PTYs (six FM1 and six FM2), can be programmed
on the six numbered pushbuttons, by performing
the following steps:
1. Press BAND, or depending on the radio, AM/FM to
select FM1 or FM2.
2. Press PROG TYPE, or depending on the radio,
P-TYPE, to activate program type select mode.
The PTY symbol displays.
3. Turn the SELECT, or depending on the radio,
P-TYPE, knob to select a PTY.
4. Press and hold one of the six numbered
pushbuttons until a beep sounds. When that
numbered pushbutton is pressed, the PTY that
was set, returns, if program type select mode
is activated.
5. Repeat the steps for each pushbutton.
RDS Messages
ALERT!:Alert warns of local or national emergencies.
When an alert announcement comes on the current
radio station, ALERT! displays. You will hear the
announcement, even if the volume is low or a CD
is playing. If a CD is playing, play stops during the
announcement. Alert announcements cannot be
turned off.
ALERT! is not affected by tests of the emergency
broadcast system. This feature is not supported by
all RDS stations.
INFO (Information):If the current station has a
message, INFO displays. Press this button to see the
message. The message can display the artist, song title,
call in phone numbers, etc.
If the entire message is not displayed, parts of the
message displays every three seconds. To scroll
through the message, press and release the INFO
button. A new group of words display after every press of
this button. Once the complete message has displayed,
the information symbol disappears from the display until
another new message is received. The last message
can be displayed by pressing the INFO button. The last
message is shown until a new message is received or
you tune to a different station.
3-50

RCL (Recall):Push this button to see how long the
current track has been playing. To change the default on
the display, track and elapsed time, push the button until
the desired option displays, then hold the button until the
display ashes. The selected display is now the default.
BAND or AM/FM:Depending on the radio, press
this button to listen to the radio when a CD is playing.
The inactive CD remains inside the radio for future
listening.
CD AUX (Auxiliary):Press this button to play a CD
while listening to the radio.
Z(Eject):For the Radios with CD, press this button
to eject a CD. Eject can be activated with either the
ignition or radio off. CDs can be loaded with the radio
and ignition off if this button is pressed rst.
Using Song List Mode
(Radio with Six-Disc CD Player)
This type of radio has a feature called song list.
This feature is capable of saving 20 track selections.
To save tracks into the song list feature, perform
the following steps:
1. Turn the CD player on and load it with at least one
CD. See “LOAD CD” listed previously in this section
for more information.
2. Check to see that the CD changer is not in song list
mode. S-LIST should not display. If S-LIST displays,
press the SONG LIST button to turn it off.
3. Select the desired CD by pressing the numbered
pushbutton and then use the SEEK SCAN right
arrow to locate the track to be saved. The
track begins to play.
4. Press and hold the SONG LIST button to save the
track into memory. When SONG LIST is pressed,
one beep sounds. After two seconds of continuously
pressing the SONG LIST button, two beeps
sound to conrm the track has been saved.
5. Repeat Steps 3 and 4 for saving other selections.
S-LIST FULL displays if more than 20 selections
are saved.
3-56

To play the song list, press the SONG LIST button.
One beep sounds and S-LIST displays. The recorded
tracks begins to play in the order they were saved.
Seek through the song list by using the SEEK SCAN
arrows. Seeking past the last saved track returns to the
rst saved track.
To delete tracks from the song list, perform the following
steps:
1. Turn the CD player on.
2. Press the SONG LIST button to turn song list on.
S-LIST displays.
3. Press the SEEK SCAN arrows to select the desired
track to be deleted.
4. Press and hold the SONG LIST button for
two seconds. When SONG LIST is pressed,
one beep sounds. After two seconds of continuously
pressing the SONG LIST button, two beeps
sound to conrm the track has been deleted.
After a track has been deleted, the remaining tracks
are moved up the list. When another track is added to
the song list, the track is added to the end of the list.To delete the entire song list, perform the following
steps:
1. Turn the CD player on.
2. Press the SONG LIST button to turn song list on.
S-LIST displays.
3. Press and hold the SONG LIST button for more
than four seconds. One beep sounds, followed
by two beeps after two seconds, and a nal beep
sounds after four seconds. S-LIST EMPTY displays
indicating the song list has been deleted.
If a CD is ejected, and the song list contains saved
tracks from that CD, those tracks are automatically
deleted from the song list. Any tracks saved to the
song list again are added to the bottom of the list.
To end song list mode, press the SONG LIST button.
One beep sounds and S-LIST is removed from the
display.
Playing an MP3 CD-R Disc
Your vehicle’s radio system may have the MP3 feature. If
it has this feature, it is capable of playing an MP3 CD-R
disc. For more information on how to play an MP3 CD-R
disc, seeUsing an MP3 on page 3-58later in this section.
3-57

Playing an MP3
Insert a CD partway into the slot, label side up.
The player pulls it in, and READING DISC displays.
The CD should begin playing and the CD symbol
displays. If you want to insert a CD with the ignition
off, rst press the eject button or the RCL button.
If the ignition or radio is turned off with a CD in the
player it stays in the player. When the ignition or radio
is turned on, the CD starts to play where it stopped,
if it was the last selected audio source.
\1 (Forward):Press and hold this pushbutton to
advance quickly within a track. Press and hold this
pushbutton for less than two seconds to advance at
10 times the normal playing speed. Press and hold it
for more than two seconds to advance at 20 times the
normal playing speed. Release this pushbutton to play
the track. FWD and the elapsed time of the track displays.
RDM 2 (Random):To repeat the tracks in the current
folder or playlist, press and release this pushbutton.
FOLDER RANDOM displays. Once all of the tracks
in the current folder or playlist have been played,
the system moves on to the next folder or playlist
and plays all of the tracks in random order.To repeat the tracks on the CD, press and hold this
pushbutton for two seconds. A beep sounds and DISC
RANDOM displays. This feature does not work with
playlists.
While in random, pressing and releasing either SEEK
arrow goes to the next or previous random track.
Press and release this pushbutton again to turn off
random play. NO RANDOM displays.
#3 (Next Folder):Press this pushbutton to go to the
rst track in the next folder or playlist. If the disc contains
playlists, it goes through the playlist, then the folders.
Pressing this button while in folder random mode takes
you to the next folder and randomizes the tracks in that
folder. This function does not work on a CD that does not
contain folders or playlists.
4
s(Reverse):Press and hold this pushbutton
to reverse quickly within a track. Press and hold this
pushbutton for less than two seconds to reverse at
10 times the normal playing speed. Press and hold it for
more than two seconds to reverse at 20 times the normal
playing speed. Release this pushbutton to play the track.
REV and the elapsed time of the track appears on the
display. If this pushbutton is pressed for more than
20 seconds, the radio stops reversing and begins to play.
3-61