Speedometer
Press
3until the speedometer is
displayed.
The speedometer shows how fast
the vehicle is moving in either miles
per hour (MPH) or kilometers per
hour (km/h). To switch between
English and metric measurements,
see “UNITS” later in this section.
The digital speedometer display can
be enabled or disabled. See
“Digital Speedometer” underDIC
Vehicle Customization on page 4-32
for more information.
UNITS
Move the thumbwheel up
Qor down
Rto highlight English or Metric
when the UNITS display is active.
Press
8to con rm the setting. This
will change the displays on the
cluster, DIC, and the temperature
display in the mirror to either English
or metric measurements.Tire Pressure
Press
3until Tire Pressure is
displayed.
The display will show a vehicle and
the approximate pressures of all
four tires. Tire pressure is displayed
in either pounds per square
inch (PSI) or in kilopascal (kPa).
This display can be customized. See
DIC Vehicle Customization on
page 4-32for more information.
Customize Options
SeeDIC Vehicle Customization on
page 4-32for more information.
Odometer/Trip Odometer
Press
3until the Odometer/Trip
Odometer is displayed.
The odometer display shows the
distance the vehicle has been driven
in either miles (MI) or kilometers
(km). To switch between English
and metric measurements, see
“UNITS” earlier in this section.The Trip Odometer display shows
the current distance traveled
since the last reset for the trip
odometer. The trip odometer can be
reset to zero by pressing and
holding
8while the trip odometer
value is highlighted. If
8is only
pressed brie y, the Avg Speed/Avg
Fuel will be reset as well.
Distance/Time To Go
Press
3until To Go is displayed.
If this item doesn’t display, check
that the display is turned on through
the Customize Options menu.
SeeDIC Vehicle Customization on
page 4-32for more information.
At the start of a trip, estimate
the distance to arrival (for example,
from maps, road signs). Move
the thumbwheel up or down until the
display shows the estimated trip
4-24 Instruments and Controls
2008 - Pontiac G8 Owner Manual
GM’s exclusive TPC Spec system
considers over a dozen critical
speci cations that impact the overall
performance of your vehicle,
including brake system performance,
ride and handling, traction control,
and tire pressure monitoring
performance. GM’s TPC Spec
number is molded onto the tire’s
sidewall near the tire size. If the tires
have an all-season tread design,
the TPC Spec number will be
followed by an MS for mud and
snow. SeeTire Sidewall Labeling on
page 9-40for additional information.
GM recommends replacing tires
in sets of four. This is because
uniform tread depth on all tires will
help keep your vehicle performing
most like it did when the tires
were new. Replacing less than a full
set of tires can affect the braking
and handling performance of
your vehicle. SeeTire Inspection
and Rotation on page 9-54for
information on proper tire rotation.{CAUTION
Mixing tires could cause you
to lose control while driving.
If you mix tires of different
sizes, brands, or types
(radial and bias-belted tires),
the vehicle may not handle
properly, and you could
have a crash. Using tires of
different sizes, brands, or
types may also cause
damage to the vehicle. Be
sure to use the correct size,
brand, and type of tires on
all wheels. It is all right to
drive with the compact
spare temporarily, as it was
developed for use on the
vehicle. SeeCompact Spare
Tire on page 9-79.{CAUTION
If you use bias-ply tires on
the vehicle, the wheel rim
anges could develop
cracks after many miles of
driving. A tire and/or wheel
could fail suddenly, causing
a crash. Use only radial-ply
tires with the wheels on the
vehicle.
If you must replace your vehicle’s
tires with those that do not have
a TPC Spec number, make
sure they are the same size, load
range, speed rating, and
construction type (radial and
bias-belted tires) as your vehicle’s
original tires.
Vehicle Service and Care 9-57
2008 - Pontiac G8 Owner Manual
