1010
Engine compartment fuses
To access the fuses located in the
engine compartment (next to the bat-
tery), remove the battery cover and
unclip the fuse box cover.
Close the fuse box cover carefully and
r e fi t t h e b a t t e r y c o v e r w h e n y o u h a v e
fi n i s h e d .
Fuse N° Rating Functions
1 20 A Engine control unit, fan assembly relay supply.
2 15 A Horn.
3 10 A Wash-wipe pump.
4 20 A Headlamp wash pump.
5 15 A Fuel pump, engine management actuators
( a i r fl o w s e n s o r , s o l e n o i d v a l v e s , . . . ) .
6 10 A ESP control unit.
7 10 A Automatic headlamp adjustment.
8 20 A Starter coil.
1010
117
The electrical system of your
vehicle is designed to oper-
ate with standard or optional
equipment.
Before installing other electrical equip-
ment or accessories on your vehicle,
contact a PEUGEOT dealer. PEUGEOT will not accept responsi-
bility for the cost incurred in repairing
your vehicle or for rectifying the mal-
functions resulting from the installation
of accessories not supplied and not
recommended by PEUGEOT and not
installed in accordance with its instruc-
tions, in particular where the equip-
ment in question consumes more than
10 milliamperes. The maxi-fuses provide additional
protection for the electrical systems.
All work must be carried out by a
PEUGEOT dealer.
Fuse N°RatingFunctions
910 A Directional headlamps control unit, additional heating sw
itching and protection control unit, clutch switch.
1030 A Engine management actuators (ignition coil, injectors, thermosta ts, solenoid valves, oxygen sensors), diesel additive pump, fuel pump, engine control unit, Blow-by heater.
1140 A Air conditioning blower.
1230 A Windscreen wipers.
1340 A Built-in systems interface supply (ignition positive).
1430 A Not used.
1010
118
CHANGING A WINDSCREEN WIPER BLADE
ECONOMY MODE FUNCTION
After the engine has stopped, certain
electrical functions can be used for a
maximum duration of approximately
one hour, to prevent discharging of the
battery.
LOAD REDUCTION FUNCTION
When driving, certain functions (air
conditioning, heated rear screen,
heating system for passenger com-
partment of diesel vehicles, etc.) may
be switched off temporarily, depending
on the level of battery charge.
Reactivation of these functions is
automatic, once the battery charge is
s u f fi c i e n t .
Note: at the risk of discharging
the battery, the functions that
have been switched off may be
reactivated manually.
Note: if the telephone is being
used when economy mode
starts, it will still be possible to
fi n i s h t h e c a l l .
A fl a t b a t t e r y p r e v e n t s t h e
engine from starting.
Replacing a blade
Lift the arm, then unclip the blade
and remove it.
Fit the new blade and fold down
the arm.
To reposition the blades, switch on the
ignition and operate the windscreen
wiper stalk. Once the hour is over, a switching to
economy mode message appears
on the multi-function display and the
active functions are put on standby.
These functions are reactivated auto-
matically next time the vehicle is driven.
In order to resume the use of these
functions immediately, the engine
must be started and left to run for a
few minutes.
The time available to you will then be
approximately double the duration
for which the engine is left running.
However, this period will always be
b e t w e e n fi v e a n d t h i r t y m i n u t e s .
T h i s t i m e m a y b e s i g n i fi c a n t l y
reduced if the battery charge
is low.
Placing the wiper blades in the
maintenance position
Less than one minute after switch-
ing off the ignition, press the wind-
screen wiper stalk down once
to position the blades at the top
of the windscreen (maintenance
position).
1010
119
Disconnecting/Reconnecting the
cables
- Raise the locking plate A .
- Position the open clip of the cable on the positive (+) terminal of the
battery.
- Press until the position checking system B tilts.
- Lock the clip by lowering the locking plate while pressing on the clip. To start the vehicle from another
battery:
- Connect the red cable to the positive
(+) terminals of the two batteries,
- Connect one end of the green or black cable to the negative (-) ter-
minal of the slave battery,
- Connect the other end of the green or black cable to an earth point on
the broken down vehicle as far as
possible from the battery,
- Operate the starter, let the engine run.
- Wait for the engine to return to idle, then disconnect the cables.
BATTERY (LOCATED IN THE ENGINE COMPARTMENT)
To charge the battery using a
battery charger:
- Disconnect the battery,
- Follow the instructions for use given by the battery charger manu-
facturer,
- Reconnect starting with the nega- tive (-) terminal,
- Check that the terminals and connec- tors are clean. If they are covered with
sulphate (white or greenish deposit),
disconnect them and clean them.
It is advisable to disconnect
the battery if the vehicle is not
to be used for a period of more
than one month.
Do not force the plate as locking
is not possible if the clip is not
positioned correctly.
Start the procedure again.