2008 PEUGEOT 308 CC DAG ignition
[x] Cancel search: ignitionPage 20 of 221
1
!
23
INSTRUMENTS and CONTROLS
The warning lights may come on
c o n t i n u o u s l y o r fl a s h .
Certain warning lights may come
on in two different modes. Only by
relating the type of lighting to the
operating status of the vehicle can
it be ascertained whether the situa-
tion is normal or whether a fault
has occurred.
Indicator and warning lights
Visual indicators informing the driver
that a system is in operation (operation
or deactivation indicator lights) or of the
occurrence of a fault (warning light).
Associated warnings
The switching on of certain warning lights
may be accompanied by an audible sig-
nal and a message on the multifunction
display.
Operation indicator lights
If one of the following indicator lights comes
o n , t h i s c o n fi r m s t h a t t h e c o r r e s p o n d i n g
system has come into operation.
Left-hand direction indicator.
Handbrake applied.
Right-hand direction
indicator.
Main beam headlamps.
Dipped headlamps.
Diesel engine pre-heating.
Wait until this is switched off
before operating the starter.
Front fog lamps.
Rear fog lamp.
When the ignition is switched on
The warning lights come on for a few
seconds when the vehicle's ignition is
switched on.
When the engine is started, these war-
ning lights should switch off.
If they remain on, before moving off,
consult the warning light concerned.
Common operation indicator lights
Page 29 of 221
1
32
INSTRUMENTS and CONTROLS
Service indicator
System which informs the driver when
the next service is due, in accor-
dance with the manufacturer's servicing
schedule.
The point at which the service is due is
calculated from the last indicator zero
reset. It is determined by two para-
meters:
- the distance travelled,
- the time elapsed since the last service. Between 600 miles (1 000 km) and
1 800 miles (3 000 km) remain before
the next service is due
For 5 seconds after the ignition is
switched on, the spanner symbolising
the service operations comes on. The
distance recorder display line indicates
the distance remaining before the next
service is due.
Example: 2 800 km remain before the
next service is due.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition is switched
on, the spanner is switched off ; the
distance recorder resumes its normal
operation. The display then indicates
the total and trip distances. Less than 600 miles (1 000 km)
remain before the next service is due
Example: 900 km remain before the
next service is due.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition is switched
on, the distance recorder resumes
its normal operation. The spanner
remains on to indicate that a service
must be carried out soon.
More than 1 800 miles (3 000 km)
remain before the next service is due
When the ignition is switched on, no ser-
vice information appears on the display.
Page 30 of 221
1
i
i
33
INSTRUMENTS and CONTROLS
Following this operation, if you
wish to disconnect the battery, lock
t h e v e h i c l e a n d w a i t a t l e a s t fi v e
mi nutes for the zero reset to be
taken into account.
Service indicator zero reset
After each service, the service indicator
must be reset to zero.
To do this, carry out the following pro-
cedure:
switch off the ignition,
press and hold the trip distance recorder zero reset button,
switch on the ignition; the distance recorder display begins a count-
down,
when the display indicates "=0" ,
release the button; the spanner dis-
appears.
The distance remaining may be
weighted by the time factor, depen-
ding on the driver's driving habits.
Therefore, the spanner may also
come on if you have exceeded the
two year service interval.
Service overdue
For 5 seconds after the ignition is
switched on,
t h e s p a n n e r fl a s h e s to
indicate that the service must be carried
out as soon as possible.
Example: the service is overdue by
300 miles (km).
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition is switched
on, the distance recorder resumes
its normal operation. The spanner
remains lit . Retrieving the service information
You can access the service information
at any time.
Press the trip distance recorder zero
reset button.
The service information is displayed for a few seconds, then disappears.
Page 31 of 221
1
i
34
INSTRUMENTS and CONTROLS
The level read will only be correct if
the vehicle is on level ground and
the engine has been off for more
than 15 minutes.
Engine oil level indicator
System which informs the driver of the
validity or invalidity of the engine oil
level.
This information is indicated for a few
seconds when the ignition is switched
on, after the service information.
Oil level correct
Lack of oil Oil level gauge fault
Dipstick
T h i s i s i n d i c a t e d b y t h e fl a s h i n g o f
"OIL" , linked with the service warning
light, accompanied by an audible signal
and a message on the multifunction dis-
play.
I f t h e l a c k o f o i l i s c o n fi r m e d b y a c h e c k
using the dipstick, it is essential that the
level is topped up to prevent damage to
the engine. T h i s i s i n d i c a t e d b y t h e fl a s h i n g o f
"OIL --"
. Consult a PEUGEOT dealer.
Refer to the "Checks" section to locate
t h e d i p s t i c k a n d t h e o i l fi l l e r c a p o n y o u r
engine. There are 2 marks on the
dipstick:
- A = max; never exceed
this level,
- B = min; top up the
l e v e l v i a t h e o i l fi l l e r
cap, using the type
of oil suited to your
engine.
Page 32 of 221
1
35
INSTRUMENTS and CONTROLS
Total distance recorder
System which measures the total dis-
tance travelled by the vehicle during its
life. Lighting rheostat
System for manual adjustment of the
brightness of the instruments and con-
trols in relation to the exterior brightness.
The total and trip distances are displayed
for thirty seconds when the ignition is
switched off, when the driver's door is
opened and when the vehicle is locked
or unlocked. Trip distance recorder
System which measures a distance
travelled during a day or other period
until it is reset to zero by the driver.
With the ignition on, press the button
until zeros appear. Activation
When the lights are on:
press the button to change the
brightness of the instruments and
controls,
when the lighting reaches the mini- mum setting, release the button,
then press again to increase it,
or
when the lighting reaches the maxi-
mum setting, release the button, then
press again to reduce it,
when the lighting reaches the level
of brightness required, release the
button.
Deactivation
When the lights are off, or in day mode
o n v e h i c l e s fi t t e d w i t h d a y t i m e l i g h t s ,
pressing the button does not have any
effect.
Page 40 of 221
2
i
i
43
MULTIFUNCTION DISPLAYS
Access to the retractable screen
Opening the screen
With the screen stored, press
control A to open it.
T h e s c r e e n o p e n s a u t o m a t i c a l l y w h e n
the ignition is switched on, when the
a u d i o a n d t e l e m a t i c s s y s t e m i s s w i t c h e d
on, when an outgoing telephone call is
made, when a voice command is given
and when a warning message linked
with the STOP warning light is received.
This screen is opened and stored auto-
m a t i c a l l y .
H o w e v e r , y o u c a n a l s o o p e n i t , s t o r e i t
a n d a d j u s t i t u s i n g t h e v a r i o u s m a n u a l
controls:
- o p e n i n g o r s t o r i n g b y m e a n s o f
control A ,
- a n g l e a d j u s t m e n t s b y m e a n s o f control B .
I t i s a l s o fi t t e d w i t h s a f e t y a u t o - r e v e r s e
protection. Closing the screen
With the screen open, press con-
trol A to store it.
T h e s c r e e n i s s t o r e d a u t o m a t i c a l l y w h e n
the ignition is switched off, after approxi-
m a t e l y t h r e e s e c o n d s , i f t h e a u d i o a n d
t e l e m a t i c s s y s t e m i s o f f .
I f y o u w i s h t h e s c r e e n t o o p e n o r
c l o s e a u t o m a t i c a l l y w h e n t h e a u d i o
a n d t e l e m a t i c s s y s t e m i s s w i t c h e d
on or off, the screen must not be
closed when the audio and telema-
t i c s s y s t e m i s o p e r a t i n g . W h e n t h e s c r e e n i s o p e n , y o u c a n
a d j u s t i t p r e c i s e l y i n d i f f e r e n t w a y s :
press the corresponding part of con-
trol B to move the screen towards
y o u o r t o w a r d s t h e w i n d s c r e e n ,
or
p u s h o r p u l l t h e s c r e e n g e n t l y b y
hand.
Adjusting the position of the screen
S a f e t y a u t o - r e v e r s e
If the screen meets an obstacle as it
opens or closes, the movement stops
i m m e d i a t e l y a n d i s r e v e r s e d b y a f e w
millimetres.
After clearing the obstacle, issue the
command required again. Storing the position of the screen
T h e s y s t e m h a s f o u r p r e - s e t p o s i t i o n s
i n i t s m e m o r y .
Each time the screen is closed, the
s y s t e m s t o r e s t h e l a s t p o s i t i o n o f t h e
screen.
Each time the screen is re-opened, the
s y s t e m r e t u r n s t h e s c r e e n t o t h e p r e - s e t
position closest to that stored.
I f y o u c l o s e t h e s c r e e n d u r i n g o p e r a -
t i o n o f t h e a u d i o a n d t e l e m a t i c s s y s -
t e m , i t w i l l o n l y r e - o p e n a u t o m a t i c a l l y
when an outgoing telephone call is
made, when a voice command is
given or when a warning message
linked with the STOP warning light is
received.
Page 42 of 221
2
!
i
i
45
MULTIFUNCTION DISPLAYS
When the route required is dis-
p l a y e d , p r e s s t h e c o n t r o l f o r m o r e
than two seconds.
Route zero reset
With the monochrome screen C or
the instrument panel large display A few definitions…
When the range falls below 20 miles
( 3 0 k m ) , d a s h e s a r e d i s p l a y e d . A f t e r
fi l l i n g w i t h a t l e a s t 5 l i t r e s o f f u e l , t h e
r a n g e i s r e c a l c u l a t e d a n d i s d i s p l a y e d
when it exceeds 60 miles (100 km).
I f d a s h e s a r e d i s p l a y e d c o n t i n u o u s l y
while driving in place of the digits,
contact a PEUGEOT dealer.
T h i s f u n c t i o n i s o n l y d i s p l a y e d f r o m
2 0 m p h ( 3 0 k m / h ) .
T h i s fi g u r e m a y i n c r e a s e f o l l o w i n g
a c h a n g e i n t h e s t y l e o f d r i v i n g o r
t h e r e l i e f , r e s u l t i n g i n a s i g n i fi c a n t
change in the current consumption.
Range
(km or miles)
This indicates the distance
which can still be travelled
with the fuel remaining in the tank in rela-
tion to the average consumption over the
last few miles (kilometres) travelled.
Current consumption
( l / 1 0 0 k m o r k m / l o r m p g )
T h i s i s t h e a v e r a g e q u a n t i t y o f
fuel consumed during the last
few seconds. A v e r a g e c o n s u m p t i o n
( l / 1 0 0 k m o r k m / l o r m p g )
T h i s i s t h e a v e r a g e q u a n t i t y
of fuel consumed since the
last trip computer zero reset.
A v e r a g e s p e e d
( k m / h o r m p h )
This is the average speed
calculated since the last trip
computer zero reset ( ignition
on).
D i s t a n c e t r a v e l l e d
(km or miles)
This indicates the distance tra-
velled since the last trip computer
zero reset.
Distance remaining
to destination
(km or miles)
This is the distance remaining to be tra-
v e l l e d t o t h e fi n a l d e s t i n a t i o n . I t i s e i t h e r
c a l c u l a t e d i n s t a n t l y b y t h e n a v i g a t i o n s y s -
tem, if guidance is activated, or entered
b y t h e u s e r .
If the distance is not entered, dashes
a r e d i s p l a y e d i n p l a c e o f t h e d i g i t s .
With the instrument panel WIP Com
3D 16/9 large display
When the required route is dis-
p l a y e d , p r e s s t h e "OK" button on
the navigator, associated with the
WIP Com 3D.
Routes "1" and "2" are independent
but their use is identical.
Route "1" p e r m i t s , f o r e x a m p l e , d a i l y
calculations, and route "2" m o n t h l y
calculations.
Page 54 of 221
3
i
56
COMFORT
FRONT SEATS
Seat consisting of a seat cushion and
a seat back which can be adjusted to
adapt your position for ease of driving
and comfort.
F o r w a r d s - b a c k w a r d s a d j u s t m e n t
Push the control forwards or rear-
wards to slide the seat. S e a t c u s h i o n h e i g h t a n d a n g l e
a d j u s t m e n t
Tilt the rear part of the control
upwards or downwards to obtain the
required height.
Tilt the front part of the control
upwards or downwards to obtain the
required angle. S e a t b a c k a n g l e a d j u s t m e n t
Tilt the control forwards or rearwards
to adjust the angle of the seat back.
E l e c t r i c a d j u s t m e n t s The electrical functions of the seat
are deactivated approximately one
minute after the ignition is switched
off.
To reactivate them, switch on the
ignition.