2008 Peugeot 107 Dag change wheel
[x] Cancel search: change wheelPage 35 of 97
3
35
COMFORT
MIRRORS STEERING WHEEL HEIGHT
ADJUSTMENT
(WITH POWER STEERING)
When stationary, lower the handle
to unlock the steering wheel.
Adjust to the desired height and
lift the handle to lock the steering
wheel.
F o l d i n g / U n f o l d i n g
When the vehicle is parked, the ex-
terior mirrors can be folded back and
unfolded manually. M a n u a l i n t e r i o r m i r r o r
The interior mirror has two positions:
- day (normal),
- night (anti-dazzle).
To change from one to the other,
push or pull the lever on the lower
edge of the mirror.
Exterior mirrors
Move the lever in all four directions to
adjust the mirror.
For safety reasons, these
operations must not be car-
ried out while driving.
Page 74 of 97
9
69
PRACTICAL INFORMATION
Parking the vehicle
As far as possible, immobilise
the vehicle on level, stable, non-
slippery ground.
Apply the handbrake, switch off
t h e i g n i t i o n a n d e n g a g e fi r s t g e a r ,
reverse or position N for the
"2 Tronic" gearbox. Tools
The following tools are installed in a
carrier, located in the centre of the
spare wheel:
1. Wheelbrace
2. Jack with handle
3. Removable towing eye
Access to the spare wheel and
the jack in the boot
Remove the carpet then the plastic
cover using the handle. Tyre pressure
This is indicated on the label posi-
tioned on the interior pillar of the left
d o o r , s e e " I d e n t i fi c a t i o n " .
CHANGING A WHEEL
If necessary, chock the wheel
diagonally opposite the wheel to
be changed.
It is imperative that you ensure
that the occupants get out of
the vehicle and wait in a safe
location.
Page 75 of 97
9
70
PRACTICAL INFORMATION R e fi t t i n g t h e w h e e l
1. Position the wheel.
2. Screw in the bolts fully by hand.
Removing the wheel
1. Remove the trim.
2. Release the wheel bolts using the
wheelbrace 1 .
3. Place the jack 2 in contact with
one of the four locations A pro-
vided on the underframe, the
one closest to the wheel to be
changed.
4. Extend the jack 2 until its base is
in contact with the ground. Ensure
that the centreline of the jack base
is directly below the location A
used.
5. Lift the vehicle.
6. Remove the bolts and detach the
wheel.
3. Pre-tighten * using the wheel-
brace 1 .
* I f y o u r v e h i c l e i s fi t t e d w i t h a l l o y w h e e l s , w h e n t i g h t e n i n g t h e b o l t s i t i s normal
to notice that the washers do not come into contact with t he spare wheel. It is
fi x e d s e c u r e l y .
Page 76 of 97
9
71
PRACTICAL INFORMATION
CHANGING A BULB
1. Side lights (W 5 W)
Turn the bulb holder A one quarter
of a turn and remove it.
Remove the bulb and change it.
2. Direction indicators (PY 21 W amber)
Turn the bulb holder B one quarter
of a turn and remove it.
Turn the bulb one quarter of a
turn.
Remove the bulb and change it.
I f y o u e n c o u n t e r a n y d i f fi c u l t i e s , c o n t a c t
a PEUGEOT dealer.
Note: in certain climatic con-
ditions (low temperatures,
humidity), the presence of
condensation on the in-
ternal face of the headlamps is
normal ; it disappears a few minutes
after the lights are switched on.
Never go underneath a vehi-
cle supported only by a jack
(use an axle stand).
4. Fold the jack 2 and detach it.
5. Tighten the wheel bolts using the
wheelbrace 1 .
6. R e fi t t h e t r i m .
7. Store the tools and the wheel in
the boot.
T h e j a c k a n d t h e t o o l k i t a r e s p e c i fi c
to your vehicle. Do not use them for
other purposes.
After changing a wheel:
-
have the tightening of the bolts and
the pressure of the spare wheel
checked as soon as possible,
- have the punctured wheel re- p a i r e d a n d r e fi t i t o n t h e v e h i c l e
as soon as possible.
Consult a PEUGEOT dealer. Front lights
1. Side lights
2. Direction indicators
3. Dipped headlamps/Main beam
headlamps
Page 77 of 97
9
71
PRACTICAL INFORMATION
CHANGING A BULB
1. Side lights (W 5 W)
Turn the bulb holder A one quarter
of a turn and remove it.
Remove the bulb and change it.
2. Direction indicators (PY 21 W amber)
Turn the bulb holder B one quarter
of a turn and remove it.
Turn the bulb one quarter of a
turn.
Remove the bulb and change it.
I f y o u e n c o u n t e r a n y d i f fi c u l t i e s , c o n t a c t
a PEUGEOT dealer.
Note: in certain climatic con-
ditions (low temperatures,
humidity), the presence of
condensation on the in-
ternal face of the headlamps is
normal ; it disappears a few minutes
after the lights are switched on.
Never go underneath a vehi-
cle supported only by a jack
(use an axle stand).
4. Fold the jack 2 and detach it.
5. Tighten the wheel bolts using the
wheelbrace 1 .
6. R e fi t t h e t r i m .
7. Store the tools and the wheel in
the boot.
T h e j a c k a n d t h e t o o l k i t a r e s p e c i fi c
to your vehicle. Do not use them for
other purposes.
After changing a wheel:
-
have the tightening of the bolts and
the pressure of the spare wheel
checked as soon as possible,
- have the punctured wheel re- p a i r e d a n d r e fi t i t o n t h e v e h i c l e
as soon as possible.
Consult a PEUGEOT dealer. Front lights
1. Side lights
2. Direction indicators
3. Dipped headlamps/Main beam
headlamps
Page 81 of 97
9
74
PRACTICAL INFORMATION
DIRECTION INDICATOR SIDE
REPEATERS
(WY 5 W AMBER)
Push the repeater forwards or
rearwards and detach it by pulling
towards you.
Disconnect the bulb holder and
change it.
CHANGING A FUSE
The fuse boxes are located under the
instrument panel trim and next to the
battery in the engine compartment.
Correct
Removing and fitting a fuse
Before changing a fuse, the cause
of the incident must be found and
r e c t i fi e d .
Use the pliers A located in the
fuse box under the bonnet.
Incorrect
Pliers A Instrument panel fuse boxes
These are located on each side of
the instrument panel under the trim.
Turn the steering wheel to the
left, remove bolt B .
Turn the steering wheel to the
right (do not forget to release the
steering wheel using the key),
remove bolt C .
Always replace a faulty fuse
with a fuse of the same
ating (same colour).
Page 82 of 97
9
74
PRACTICAL INFORMATION
DIRECTION INDICATOR SIDE
REPEATERS
(WY 5 W AMBER)
Push the repeater forwards or
rearwards and detach it by pulling
towards you.
Disconnect the bulb holder and
change it.
CHANGING A FUSE
The fuse boxes are located under the
instrument panel trim and next to the
battery in the engine compartment.
Correct
Removing and fitting a fuse
Before changing a fuse, the cause
of the incident must be found and
r e c t i fi e d .
Use the pliers A located in the
fuse box under the bonnet.
Incorrect
Pliers A Instrument panel fuse boxes
These are located on each side of
the instrument panel under the trim.
Turn the steering wheel to the
left, remove bolt B .
Turn the steering wheel to the
right (do not forget to release the
steering wheel using the key),
remove bolt C .
Always replace a faulty fuse
with a fuse of the same
ating (same colour).
Page 83 of 97
9
74
PRACTICAL INFORMATION
DIRECTION INDICATOR SIDE
REPEATERS
(WY 5 W AMBER)
Push the repeater forwards or
rearwards and detach it by pulling
towards you.
Disconnect the bulb holder and
change it.
CHANGING A FUSE
The fuse boxes are located under the
instrument panel trim and next to the
battery in the engine compartment.
Correct
Removing and fitting a fuse
Before changing a fuse, the cause
of the incident must be found and
r e c t i fi e d .
Use the pliers A located in the
fuse box under the bonnet.
Incorrect
Pliers A Instrument panel fuse boxes
These are located on each side of
the instrument panel under the trim.
Turn the steering wheel to the
left, remove bolt B .
Turn the steering wheel to the
right (do not forget to release the
steering wheel using the key),
remove bolt C .
Always replace a faulty fuse
with a fuse of the same
ating (same colour).