9
118
Removing a wheel
-
Place the chock 2 (integrated with the
box) at the rear of the wheel diagonal-
ly opposite the wheel to be changed.
- Remove the wheel trim, using the wheelbrace 3 , by pulling at
the valve passage hole.
-
Remove the chrome-plated bolt
covers and the plastic cover from
the bolts using the "bolt cover" tool 5
(Special features of alloy wheels).
- Slacken the wheel bolts.
- Place the jack 1 under one of the
four locating points A on the sub-
frame closest to the wheel to be
changed. Ensure that the entire
surface of the jack base plate is
in contact with the ground.
-
Extend the jack, completely unscrew
the bolts and remove the wheel.
Refitting the wheel
- Position the wheel on the hub.
- Lightly pre-tighten the bolts us- ing the wheelbrace 3 .
-
Compress the jack 1 and release it.
- Fully tighten the bolts using the
wheelbrace.
- Replace the trim, starting at the valve passage hole, and press it
on using the palm of the hand.
For your safety, always
change a wheel:
- Stow the tools in the case, then
put it back in the left boot trim.
T h e j a c k a n d t h e t o o l k i t a r e s p e c i fi c
to your vehicle. Do not use them for
other purposes.
Replacing the wheel in the
carrier
- Replace the jack 1 in the box.
- Replace the box in the wheel.
- Replace the wheel in the carrier.
- Lift the wheel then the carrier and reposition the hook.
- Do not forget to fully tighten the spare wheel carrier retaining bolt. After changing the wheel
- Have the tightening of the bolts
and the pressure of the spare
tyre checked as soon as possi-
ble by a PEUGEOT dealer.
-
Do not exceed its maximum autho-
rised speed: 50 mph (80 km/h).
- Have the punctured tyre repaired and replace it on the vehicle as
soon as possible.
- 15 and 16 inch punctured wheels cannot be placed in the carrier.
- on level, stable and non-slippery
ground,
- with the handbrake applied,
- w i t h fi r s t o r r e v e r s e g e a r e n g a g e d (position R for the "2 Tronic"
gearbox),
- with the vehicle chocked,
- never go underneath a vehicle raised using a jack (use an axle
stand).
9
119
Special features of alloy
wheels Fitting the spare wheel
I f y o u r v e h i c l e i s fi t t e d w i t h a s t e e l
s p a r e w h e e l , w h e n fi t t i n g i t , i t i s
nor-
mal when tightening the bolts to no-
tice that the washers do not come
into contact with the rim. The spare
wheel is secured by the cone shape
of each bolt. This anti-theft socket was
given to you on delivery of
your vehicle along with the
duplicate keys.
Make a careful note of the code
number engraved on the head of the
anti-theft socket. This will enable you
to obtain a duplicate socket from a
PEUGEOT dealer.
Fitting snow tyres
I f y o u fi t s n o w t y r e s m o u n t e d o n s t e e l
wheels onto your vehicle, it is es-
sential to use special bolts available
from PEUGEOT dealers.
Wheels equipped with 195/50R16
t y r e s c a n n o t b e fi t t e d w i t h s n o w
chains.
For further information, contact a
PEUGEOT dealer.
Bolt covers
Alloy wheel bolts are covered by
chrome trims.
Use the yellow tool to remove the
trims before slackening the bolts. Anti-theft bolts
I f y o u r w h e e l s a r e fi t t e d w i t h a n a n t i -
theft bolt (one per wheel), the chrome
trim must be removed before un-
screwing the bolt using the anti-theft
socket and the wheelbrace.
