2008 PEUGEOT 1007 instrument panel
[x] Cancel search: instrument panelPage 111 of 189
7
104
Switching to automated mode Reinitialisation
Following disconnection of the battery,
the gearbox must be reinitialised: The brake pedal must be
pressed while starting the
engine.
Never select neutral
N while
the vehicle is moving.
Only engage reverse gear R with the
vehicle immobilised and the brake
pedal pressed.
In all cases, it is imperative that you
apply the handbrake in order to im-
mobilise the vehicle.
On a steep gradient, it is preferable
to switch to sequential mode.
"Auto sequential" mode
In the automated mode, you can re-
sume control temporarily at any time
using the steering wheel controls.
The use of these controls permits
manual selection of the gears in situa-
tions which require a faster change-
down than that offered in automated
m o d e ( a r r i v a l a t a r o u n d a b o u t , e x i t
from a car park with a steep gradient,
overtaking...).
The gearbox engages the gear
requested if the engine speed
permits it.
"AUTO" is still displayed
on the instrument panel.
After a few moments, the gearbox
again controls the gears automatically.
Stopping the vehicle
Before switching off the engine, you
can:
- move to position N to leave the
gearbox in neutral.
- leave a gear engaged, such as fi r s t o r r e v e r s e .
In both cases, it is imperative that you
apply the handbrake to immobilise
the vehicle. Operating anomaly
W i t h t h e i g n i t i o n o n , t h e fl a s h i n g o f
"AUTO" and lighting of the service
warning light, accompanied by an
audible signal and a message on the
multifunction display, indicate a gear-
box malfunction.
Contact a PEUGEOT dealer without
delay.
If you press the accelera-
tor pedal beyond the point
of resistance, the gearbox
selects the gear below to
permit sharper acceleration. - switch on the ignition,
"AUTO"
and "-" appear on the instrument
panel display,
- press the brake pedal,
- wait approximately 30 seconds until "N" or a gear appears on
the instrument panel display,
- release the brake pedal.
The gearbox is operational again.
Automated mode
After using the sequential mode, you
can return to the automated mode by
selecting position
A .
"AUTO" and the gear engaged ap-
pear on the instrument panel display.
The gearbox then operates in auto-
active mode, without any action on
the part of the driver.
It continuously selects the gear most
suited to the following parameters:
- driving style,
- road characteristics,
- vehicle load.
To optimise driving comfort and ob-
tain the most suitable gear, avoid
sharp variations in the pressure on
the accelerator pedal.
Page 112 of 189
7
105
Steering wheel controls
This system’s controls are grouped
together on lever A .
1. Speed limiter mode selection dial
2. Value decrease button
3. Value increase button
4. Speed limiter on/off button Instrument panel display
The programmed information is grou-
ped together on the instrument panel
display.
5. Speed limiter on/off indication
6. Speed limiter mode selection
indication
7. Programmed speed value
SPEED LIMITER
This speed limiter, of the new gene-
ration, has a display on the instrument
panel to indicate the programmed
speed.
It prevents exceeding of the vehicle
speed programmed by the driver.
When the programmed speed is
reached, pressing the accelerator
pedal no longer has any effect.
The limiter operates with a pro-
grammed speed of at least 18 mph
( 3 0 k m / h ) ; i t r e m a i n s a c t i v e r e g a r d -
less of any action on the brake and
clutch pedals.
The speed limiter is switched on
manually: it requires a programmed
s p e e d o f a t l e a s t 1 8 m p h ( 3 0 k m / h ) .
The speed limiter is switched off by
manual operation of the control.
By pressing the accelerator pedal
fi r m l y , p a s s i n g t h e p o i n t o f r e s i s -
tance, it is possible to exceed the
programmed speed temporarily.
To return to the programmed speed,
simply slow down to a speed below
the programmed speed.
The programmed speed value re-
mains in the memory when the igni-
tion is switched off.
Page 114 of 189
7
1 0 7
CRUISE CONTROL
This cruise control, of the new gene-
ration, is linked with the speed limiter. It
has a display on the instrument panel
to indicate the memorised reference
speed.
It enables the vehicle to maintain a
steady speed programmed by the
driver.
The cruise control is switched on
manually: it requires a minimum
v e h i c l e s p e e d o f 2 5 m p h ( 4 0 k m / h )
and fourth gear must be engaged on
the manual gearbox.
The cruise control is switched off
by means of a manual action or by
pressing the brake or clutch pedal or
in the event of activation of the ESP.
By pressing the accelerator pedal, it is
possible to exceed the programmed
speed temporarily.
To return to the programmed speed,
simply release the accelerator pedal.
Switching off the ignition or turning
the dial cancels any programmed
speed value. Instrument panel display
The programmed information is grou-
ped together on the instrument panel
display.
5. Cruise control on/off indication
6. Cruise control mode selection
indication
7. Programmed speed value
Steering wheel controls
This system’s controls are grouped
together on lever
A .
1. Cruise control mode selection dial
2. Value decrease button
3. Value increase button
4. Cruise control on/off button
Page 121 of 189
8
115
CHECKING THE LEVELS
There are two marks on
the dipstick:
A = maximum
N e v e r fi l l p a s t t h i s m a r k .
B = minimum
Dipstick
Oil change
According to the information given in
the servicing booklet. Changing the brake fluid
T h e b r a k e fl u i d m u s t b e
changed at the intervals stat-
ed, according to the manu-
facturer’s servicing schedule.
U s e fl u i d s r e c o m m e n d e d b y t h e
m a n u f a c t u r e r , w h i c h f u l fi l D O T 4
standards. Windscreen and headlamp
wash level
For best quality cleaning and
for your safety, we would ad-
vise that you use products
recommended by PEUGEOT .
When the level is low, this is indicated
by an audible signal and a message
on the multifunction display.
Viscosity selection
In all cases, the oil selected must
meet the manufacturer’s require-
ments.
Cooling system
U s e t h e fl u i d r e c o m m e n d e d b y t h e
manufacturer.
When the engine is warm, the tem-
perature of the coolant is controlled
by the engine fan. As this fan can ope-
rate with the ignition key removed
and because the cooling system is
pressurised, wait for at least one hour
after the engine has stopped before
carrying out any work.
Slacken the cap by two turns to re-
lease the pressure to prevent any
risk of scalding. When the pressure
has dropped, remove the cap and
top up the level. Diesel additive level (Diesel
with particle emission filter)
Lighting of the service warning light,
accompanied by a message and an
audible signal, indicates that the die-
sel additive level is low.
This additive must be topped up.
Contact a PEUGEOT dealer as soon
as possible.
To maintain the reliability of
engines and emission control
systems, the use of additives
in engine oil is prohibited. Used oil
Avoid prolonged contact of used oil
with the skin.
B r a k e fl u i d i s h a r m f u l t o h e a l t h a n d
very corrosive.
Note: the coolant does not need to
be changed.
The level must always be
above the MIN mark and
close to the MAX mark. Do not dispose of used oil,
b r a k e fl u i d o r c o o l a n t i n t o
drains or into the ground.
Oil level
Check the level regularly and
top up between changes. The
maximum consumption is 0.5 l
per 600 miles (1 000 km).
Check the level with the ve-
hicle level, engine cold, using the oil
level gauge on the instrument panel
or the dipstick.
Page 131 of 189
9
124
Fuse N° Rating
Functions
1 15 A Rear wiper.
3 5 A Air bags and pre-tensioners control unit.
4 10 A Diagnostic socket - Clutch switch - Steering wheel angle sensor
-
P a r t i c l e e m i s s i o n fi l t e r p u m p .
5 30 A Electric windows - Sunroof.
6 - Not used.
7 5 A Courtesy light - Glove box light.
8 20 A T y r e u n d e r - i n fl a t i o n d e t e c t i o n c o n t r o l u n i t - F o l d i n g o f t
h e e l e c t r i c m i r r o r s - A l a r m s i r e n -
Multifunction display - Alarm control unit - Audio equipment - Aud io/telephone.
9 30 A Audio equipment - Lighter/12 V socket (100 W max.).
10 15 A Steering wheel controls.
11 15 A Diagnostic socket - Low current ignition switch - Motorised strik ers.
12 15 A Air bags and pre-tensioners control unit - Rain/brightness sens or.
13 5 A ABS relay - Speed sensor - Engine Fuse Box - "2 Tronic" gear lever - Brake switch.
14 15 A Parking assistance control unit - "Sesame" doors control unit and swit
ches -
Instrument panel - Seat belt warning lights bar - Air condition ing control panel -
Headlamp adjustment - Hands-free kit.
15 30 A Locking - Deadlocking - Unlocking.
17 40 A Rear screen and exterior mirrors demisting.
SH - PARC shunt.