2008 PEUGEOT 1007 ESP
[x] Cancel search: ESPPage 118 of 189
8
112
From outside: lift the catch A and
raise the bonnet. Bonnet strut
Secure the strut to hold the bonnet
open.
Before closing the bonnet, replace
the strut in its housing.
To close
Lower the bonnet and release it at
the end of its travel. Check that the
bonnet is properly locked.
OPENING THE BONNET
From inside: pull the handle on the
left-hand side under the fascia.
RUNNING OUT OF FUEL (DIESEL)
I f y o u r v e h i c l e i s fi t t e d w i t h a n H D I
engine, the fuel circuit must be rep-
rimed if you run out of fuel (refer to
the corresponding graphic).
This system consists of a repriming
pump and a transparent pipe.
1.4 litre Turbo HDI engine
Open the bonnet.
Fill the fuel tank with at least
fi v e l i t r e s o f d i e s e l .
Squeeze and release the rep-
riming pump until fuel appears in
the transparent pipe.
Operate the starter until the en-
gine starts.
Close the bonnet.
1.6 litre Turbo HDI 16V engine
Open the bonnet.
Fill the fuel tank with at least
fi v e l i t r e s o f d i e s e l .
Unclip the style cover to gain ac-
cess to the repriming pump.
Squeeze and release the rep-
riming pump until fuel appears
in the transparent pipe with the
green connector.
Operate the starter until the en-
gine starts.
Put the style cover back in posi-
tion and clip it in place.
Close the bonnet.
Opening the bonnet may
cause serious injuries,
please observe the following
recommendations:
- protect your hands and clothing,
- always allow the engine to cool before opening the bonnet,
- place the strut in its housing on the wing correctly,
- c h e c k t h a t t h e b o n n e t i s fi r m l y secured in the open position,
- be aware of gusts of wind as they could cause the bonnet to
close suddenly.
Page 128 of 189
9
122
Rear lights
1. Brake/side lights
(P21 W/5 W).
2. Direction indicators
(P21 W).
3. Reversing light
(P21 W), left side.
Fog lamp (P21 W), right side.
These 4 bulbs are changed by re-
moving the light:
R e m o v e t h e a c c e s s fl a p i n t h e
corresponding boot side trim to
access the light,
R e m o v e t h e t w o l i g h t fi x i n g n u t s
inside the boot,
Unclip the harness,
Remove the light pressing on the
retaining tabs,
Remove the seal,
Remove the bulb holder moving
aside the two tabs A ,
Turn the bulb a quarter of a turn,
Remove the bulb and change it.
Note: if necessary, use the wheel-
brace to remove the nuts.
W h e n r e fi t t i n g , p r o c e e d i n t h e r e -
verse order and take care to position
the bulb holder, the seal and the light
correctly. Third brake light
(4 W 5 W bulbs)
Using a 10 mm box spanner, un-
s c r e w t h e 2 fi x i n g n u t s A .
Release the lamp unit by push-
ing it outwards.
Disconnect the connector and
the rear wash-wipe pipe.
Turn the bulb holder a quarter of
a turn and remove it.
Remove the bulb and change it.
W h e n r e fi t t i n g , p r o c e e d i n t h e r e v e r s e
order and ensure that the lamp unit
seal and the rear wash-wipe pipe have
been put back in place correctly.
Do not tighten the nuts more than is
necessary at the risk of breaking the
light.
Number plate lights (W 5 W)
Insert a thin screwdriver into one
of the external holes of the lens.
Push it outwards to unclip it.
Remove the lens.
Remove the bulb and change it.
Page 132 of 189
9
125
Engine compartment fuse box
Unclip the cover to gain access
to the fuses. Your vehicle's electrical sys-
tem is designed to operate
with standard or optional
equipment.
Once the work has been carried out,
close the cover very carefully.
** The maxi fuses provide addi-tional protection for the electrical
systems. All work must be car-
ried out by a PEUGEOT dealer.
Fuse N° Rating Functions
MF1 ** 50 A Fan assembly.
MF2 ** 30 A ABS/ESP control unit.
MF3 ** 30 A ABS/ESP control unit.
MF4 ** 60 A Built-in Systems Interface supply.
MF5 ** 60 A Built-in Systems Interface supply.
MF6 ** 30 A "2 Tronic" gearbox control unit.
MF7 ** 80 A Passenger compartment fuse box -
"Sesame" doors control unit.
MF8 ** 80 A Electric power steering. Before installing other electrical
equipment or accessories on your
vehicle, contact a PEUGEOT dealer.
Some electrical accessories or the
w a y i n w h i c h t h e y a r e fi t t e d m a y h a v e
damaging effects on the operation of
your vehicle (audio, control and elec-
trical load circuits).
PEUGEOT will not accept responsi-
bility for the cost incurred in repairing
your vehicle or for rectifying malfunc-
tions resulting from the installation
of auxiliary accessories not supplied
and not recommended by PEUGEOT
and not installed in accordance with
its instructions, in particular where
the equipment in question consumes
more than 10 milliamperes.
Page 133 of 189
9
126
Fuse N° Rating
Functions
1 20 A Engine control unit and fan assembly control supply - Injection
control unit (Diesel) -
I n j e c t i o n p u m p ( D i e s e l ) - A i r h e a t i n g s o l e n o i d v a l v e s ( D i e s e l ) - A i r fl o w s e n s o r ( D i e s e l ) .
2 15 A Horn.
3 10 A Front and rear wash-wipe pump.
4 20 A Headlamp wash pump.
5 15 A Fuel pump (petrol).
6 10 A Power steering control unit - Water in diesel sensor - Vehicl e speed sensor.
7 10 A Switching and protection unit (Diesel) - Engine coolant l evel detector (Diesel).
8 25 A Starter.
9 10 A ABS/ESP control unit - ABS cut-off relay - Brake switch.
10 30 A Engine control unit actuators (petrol: ignition coils, oxygen
sensors, injectors,
purge canister and variable timing solenoid valves, controlled t hermostat)
( D i e s e l : i n j e c t i o n c o n t r o l u n i t , a i r fl o w s e n s o r , i n j e c t i o n p u m p , d i e s e l h i g h p r e s s u r e
regulator, EGR and Turbo pressure regulation solenoid valves) - Blow-by heaters -
Diesel heater.
11 40 A Air blowers.
12 30 A Windscreen wipers (low/high speed).
13 40 A (Ignition positive) Built-In Systems Interface.
14 - Not used.
15 10 A Right main beam headlamp.
16 10 A Left main beam headlamp.
17 15 A Left dipped headlamp.
18 15 A Right dipped headlamp.
Page 135 of 189
9
128
BATTERY
The batteries contain harm-
ful substances such as sul-
phuric acid and lead. They
must be disposed of in ac-
cordance with regulations and must
never be discarded with household
waste.
Take used remote control and vehi-
cle batteries to a special collection
point.
To start the vehicle from
another battery:
-
Connect the red cable to the positive
(+) terminals of the two batteries,
- Connect the green or black ca-
ble to the negative (-) terminals
of the two batteries,
- Operate the starter, let the en- gine run,
- Wait for the engine to return to idle, then disconnect the cables.
Before disconnecting the
battery, you must wait for
2 minutes after switching off
the ignition.
Never disconnect a terminal when
the engine is running.
N e v e r c h a r g e a b a t t e r y w i t h o u t fi r s t
disconnecting the terminals.
Close the windows, the sunroof and
the doors before disconnecting the
battery. If they do not operate nor-
mally following reconnection of the
battery, they must be reinitialised
(see sections "Sesame doors" and
"Sunroof"). After every reconnection of the battery:
- switch on the ignition and wait
1 minute before starting to al-
low the electronic systems to be
i n i t i a l i s e d . I f s l i g h t d i f fi c u l t i e s a r e
experienced after this, please
contact a PEUGEOT dealer.
- reinitialise the "2 Tronic" gearbox (refer to the corresponding sec-
tion).
A. Flat battery
B. Slave battery
It is advisable to disconnect
the battery if the vehicle is
not to be used for a period
of more than one month.
To charge the battery using a
battery charger:
- Disconnect the battery,
- Follow the instructions for use
given by the battery charger
manufacturer,
- Reconnect starting with the neg- ative (-) terminal,
- Check that the terminals and connectors are clean. If they are
covered with sulphate (white or
greenish deposit), disconnect
them and clean them.
Page 165 of 189
11
SOU R CE
22
S
O S SOU R CE
MODE B AND TP T
A
Y
DARKSOU R CE
2
abc
5
jkl
8
tuv 3
def
6
mno
9
wxyz
1 4
ghi
7
pqrs
0 #
D
2
abc
5
jkl
8
tuv
3
def
6
mno
9
wxyz
1 4
ghi
r
7
pq s0 #
S
O S SOU R CE
MODE B AND TP T
A
Y
DARKSOU R CESOU R CE
ESC
MENU LIST
1
33
22
158
Press the MENU button then select the CONFIGURATIO N function,
then SOUNDS, then ACTIVATE AUXILIARY SOURCE to acti vate
the auxiliary input of the RT4 GPS audio/telephone.
Connect the portable equipment (MP3
p l a y e r … ) t o t h e a u d i o s o c k e t s ( w h i t e a n d
r e d , R C A t y p e ) l o c a t e d i n t h e g l o v e b o x
using a JACK/RCA audio cable.
Press the SOURCE button several
times in succession and select AUX. CD CHANGER
Insert one or more CDs in the
changer.
Press the SOURCE button several
times in succession and select CD
CHANGER.
Press one of the buttons on the
alphanumeric keypad to select the
corresponding CD.
Press one of the buttons to select a
track on the CD.
The displaying and management of the commands take s place via
the portable equipment.
I t i s n o t p o s s i b l e t o c o p y t h e fi l e s o n t o t h e h a r d d i s c f r o m t h e a u x i l i a r y
input. I t i s n o t p o s s i b l e t o c o p y t h e fi l e s o n t o t h e h a r d
d i s c f r o m t h e C D
changer.
USING THE AUXILIARY INPUT (AUX)
JACK/RCA AUDIO CABLE NOT SUPPLIED PLAYING A CD (NOT MP3 C
OMPATIBLE)
Page 176 of 189
180
The table below groups together the answers to the most frequently asked questions concerning the RD4 audio equipment and the RT4 audio/telephone.
QUESTION SOLUTION
RESPONSE
There is a difference in
sound quality between
the different audio
sources (radio, CD, CD
c h a n g e r . . . ) . Check that the audio settings (Volume, Bass,
T r e b l e , A m b i e n c e , L o u d n e s s ) a r e a d a p t e d t o
the sources listened to. It is advisable to set
the AUDIO functions (Bass, Treble, Front-Rear
B a l a n c e , L e f t - R i g h t B a l a n c e ) t o t h e m i d d l e
position, select the musical ambience "None"
and set the loudness correction to the "Active"
position in CD mode or to the "Inactive" position
in radio mode.
For optimum sound quality, the audio settings (Vol
ume, Bass, Treble,
A m b i e n c e , L o u d n e s s ) c a n b e a d a p t e d t o t h e d i f f e r e n t s o u n d s o u r c e s ,
which may result in audible differences when changi ng source (radio, CD,
C D c h a n g e r . . . ) .
The CD is ejected
automatically or is not
played by the player. - Check that the CD is inserted in the player t
he
right way up.
- Check the condition of the CD: the CD cannot be played if it is too damaged.
- Check the content in the case of a recorded CD: consult the advice in the Audio section.
- The audio equipment's CD player does not play DVDs.
- Due to inadequate quality, certain recorded CDs will not be played by the audio system.
- The CD changer does not play MP3 CDs.
The CD is inserted upside down, is unplayable, doe
s not contain any audio
data or contains an audio format which the player c annot play.
The CD is protected by an anti-pirating protection system which is not
recognised by the audio equipment.
FREQUENTLY ASKED QUESTIONS
The CD player sound
is poor. The CD used is scratched or of poor quality. Inse
rt good quality CDs and store them in
suitable conditions.
T h e a u d i o e q u i p m e n t s e t t i n g s ( b a s s , t r e b l e , a m b i e n c e s ) a r e u n s u i t a b l e . Set the treble or bass level to 0, without selecti ng
an ambience.
Page 177 of 189
181
QUESTION SOLUTION
RESPONSE
The stored stations do
not function (no sound,
8 7 . 5 M h z i s d i s p l a y e d . . . ) An incorrect waveband is selected.
Press the BAND AST button to return to the
w a v e b a n d ( A M , F M 1 , F M 2 , F M A S T ) o n w h i c h t h e
stations are stored.
T h e t r a f fi c a n n o u n c e m e n t
( T A ) i s d i s p l a y e d . I d o
n o t r e c e i v e a n y t r a f fi c
information. T u n e t o a r a d i o s t a t i o n w h i c h b r o a d c a s t s t r a f fi c
information.
T h e r a d i o s t a t i o n i s n o t p a r t o f t h e r e g i o n a l t r a f
fi c i n f o r m a t i o n n e t w o r k .
The quality of reception
of the radio station
listened to gradually
deteriorates or the
stored stations do
not function (no
sound, 87.5 Mhz is
d i s p l a y e d . . . ) . The vehicle is too far from the transmitter used b
y the station listened to or
there is no transmitter in the geographical area th rough which the vehicle
is travelling.
T h e e n v i r o n m e n t ( h i l l s , b u i l d i n g s , t u n n e l s , b a s e m e n t c a r p a r k s . . . ) b l o c k
reception, including in RDS mode.
The aerial is absent or has been damaged (for exam ple when going
t h r o u g h a c a r w a s h o r i n t o a n u n d e r g r o u n d c a r p a r k ) . Activate the RDS function to enable the system
to check whether there is a more powerful
transmitter in the geographical area.
This phenomenon is normal and does not
indicate a failure of the audio equipment.
Have the aerial checked by a PEUGEOT dealer.
Sound cut-outs of 1
to 2 seconds in radio
mode. During this brief sound cut-out, the RDS searches
for any frequency
permitting better reception of the station. Deactivate the RDS function if the phenomenon
is too frequent and always on the same route.
With the engine off,
the audio equipment
switches off after a few
minutes of use. When the engine is switched off, the audio equipme
nt operating time
depends on the battery charge.
The switch-off is normal: the audio equipment swit ches to economy mode
and switches off to prevent discharging of the vehi cle's battery. Start the vehicle's engine to increase the battery
charge.
The message "the audio
system is overheated"
appears on the display. Switch the audio system off for a few minutes to
allow the system to cool.
In order to protect the installation if the surrou
nding temperature is too
high, the audio equipment switches to an automatic thermal protection
mode leading to a reduction of the volume or stoppi ng of the playing of the
CD.