2008 PEUGEOT 1007 DAG lock
[x] Cancel search: lockPage 51 of 194
3
54
REAR SEATS
Seat back angle adjustment
Tilt the control C and adjust the angle
to the comfort or loading position.
Release the control to lock. Folding/Placing in the "fully
folded" position
Place the head restraint in the low
position.
Position the seat belt buckle as close
as possible to the strap return.
Move the seat as far back as possi-
ble using the bar A or the handle B .
Fold the seat back onto the seat
cushion tilting control C fully.
Note: you can lock the seat back in
this position by pressing on it.
Push the control D upwards to release
the rear feet.
Place the seat in the "fully folded"
position.
When driving, the seat is retained in
this position by the side strut.
Table position
Place the head restraint in the low
position.
Fold the seat back onto the seat
cushion tilting control
C fully.
Note: you can lock the seat back in
this position by pressing on it.
Forwards-backwards
adjustment
Lift the bar
A and slide the seat for-
wards or backwards.
From the boot, you can press the red
handle B and slide the seat forwards
or backwards.
This manoeuvre makes folding of the
seat when loading the boot easier.
Page 52 of 194
3
55
Never drive with the head re-
straints removed, they must
be in place and correctly
adjusted.
Locked Released
In order to ensure that the
seat covers have a long ser-
vice life, do not leave the seat
in the table or "fully folded"
position after loading.
Avoid placing luggage on the seats
when they are in the table position.
REAR HEAD RESTRAINTS
The rear head restraints can be re-
m o v e d a n d h a v e t w o p o s i t i o n s ;
- high, position for use
- low, storage position
Repositioning the seat
Press the control D upwards to check
that the rear feet are released.
Tilt the folded seat rearwards.
The rear feet are secured automati-
cally.
Check that the seat is secured correctly.
R a i s e t h e s e a t b a c k , r e l e a s i n g i t fi r s t
by pulling the control C . To raise a head restraint, pull it up-
wards.
To lower it, press the lug then the
head restraint.
To remove it, place it in the high posi-
tion, push the lug and pull it upwards.
T o r e fi t i t , e n g a g e t h e h e a d r e s t r a i n t
rods in the holes taking care to remain
in the centreline of the seat back.
Page 59 of 194
3
62
"ISOFIX" MOUNTINGS
Your vehicle has been approved in
accordance with the new ISOFIX
regulation .
The seats * , represented below, are
fi t t e d w i t h r e g u l a t i o n I S O F I X m o u n t -
ings: These are three rings for each seat: This ISOFIX mounting system
guarantees you fast, reliable and
s a f e fi t t i n g o f t h e c h i l d s e a t i n y o u r
vehicle.
The ISOFIX child seats a r e fi t t e d
with two locks which are secured
easily on these lower rings A .
Some also have an upper strap
which is attached to the upper ring B .
- two lower rings A , located be-
tween the vehicle seat back and
cushion, indicated by a label,
- an upper ring B , referred to as
the TOP TETHER , indicated by
a label. To attach this strap, raise the
vehicle seat's head restraint
then pass the hook between
i t s r o d s . T h e n fi x t h e h o o k o n
the upper ring
B and tighten
the upper strap.
The incorrect installation of a
child seat in a vehicle compro-
mises the child's protection in
the event of an accident.
For information regarding the ISOFIX
child seats which can be installed in
your vehicle, consult the summary
table for the location of the ISOFIX
child seats.
C h i l d s e a t s fi t t e d w i t h a s u p p o r t w h i c h
r e s t s o n t h e fl o o r o f t h e v e h i c l e m u s t
not be installed in the rear
* According to version.
Page 69 of 194
4
72
THE REMOTE CONTROL KEY
The remote control permits locking,
deadlocking, unlocking and locating of
the vehicle, as well as folding and un-
folding of the exterior mirrors. It does
not work when the ignition is on.
The key permits mechanical and in-
d e p e n d e n t o p e r a t i o n o f t h e f u e l fi l l e r
cap and passenger air bag disarming
switch as well as switching on of the
ignition.
From the driver's door, the key per-
mits electrical control of the locking,
deadlocking and unlocking of the ve-
hicle, as well as folding and unfolding
of the exterior mirrors.
If one of the doors or the tailgate is
open, the central locking does not
work. Using the key
Turn the key in the lock on the driver's
door to lock the vehicle.
N o r m a l l o c k i n g i s c o n fi r m e d b y fi x e d
lighting of the direction indicators for
approximately two seconds.
The exterior mirrors fold at the same
time.
Using the key
Turn the key in the lock on the driver's
door to unlock the vehicle.
U n l o c k i n g i s c o n fi r m e d b y r a p i d
fl a s h i n g o f t h e d i r e c t i o n i n d i c a t o r s f o r
approximately two seconds.
The exterior mirrors unfold at the
same time.
Folding/Unfolding the key
To fold the key, press button
A then
fold the key into the casing of the re-
mote control.
To unfold the key, press button A .
Unlocking
Normal locking When the vehicle is locked, if
unlocking is activated inadver-
tently, without the doors being
opened within 30 seconds, the
vehicle will lock automatically.
The folding and unfolding of the ex-
terior mirrors can be deactivated by
a PEUGEOT dealer.
The remote control does not work
when the ignition is on.
Using the remote control
Press button B to lock the vehicle.
Pressing button B for more than
2 seconds permits automatic closing
of the windows and sunroof in addition
to locking.
E a c h a c t i o n i s c o n fi r m e d b y fi x e d
lighting of the direction indicators for
approximately two seconds.
The exterior mirrors fold at the same
time. Using the remote control
Press button
C to unlock the vehicle.
T h i s i s c o n fi r m e d b y r a p i d fl a s h i n g o f
the direction indicators.
The exterior mirrors unfold at the
same time.
Page 70 of 194
4
73
Deadlocking
Deadlocking renders the internal and
external door controls inoperative.
It also deactivates the internal central
locking button.
Using the remote control
Pressing button B locks the vehicle
or pressing button B for more than
2 seconds permits automatic closing
of the windows and sunroof in addi-
tion to locking.
A second press w i t h i n fi v e s e c o n d s
deadlocks the vehicle.
E a c h a c t i o n i s c o n fi r m e d b y fi x e d
lighting of the direction indicators for
approximately two seconds. Opening/Closing the
"Sesame" doors
Pressing button D or E opens or
closes the left or right door.
This press unlocks the vehicle before
opening the corresponding door.
A second press stops the move-
ment of the corresponding door.
A third press reverses the move-
ment of the corresponding door.
Using the key
Turn the key in the lock on the driver's
door to lock the vehicle.
W i t h i n t h e n e x t fi v e s e c o n d s , t u r n t h e
key again to deadlock the vehicle.
E a c h a c t i o n i s c o n fi r m e d b y fi x e d
lighting of the direction indicators for
approximately two seconds. Key in ignition
A buzzer sounds on opening the driver's
door, if the key has been left in the
ignition.
Locating your vehicle
To locate your vehicle, if you have
locked it, in a car park:
press button B , the courtesy
lights come on and the direction
i n d i c a t o r s fl a s h f o r a f e w
seconds.
If the deadlocking is opera-
ted from inside the vehicle, it
will change to normal locking
when the vehicle is started.
When closing the windows
and sunroof using the remote
control, the user must ensure
that no one is preventing cor-
rect closing of the windows
and sunroof.
Never leave anyone inside the vehicle
when it is deadlocked.
Page 71 of 194
4
74
ELECTRONIC ENGINE IMMOBILISER
This locks the engine control system
a few moments after the ignition has
been switched off and therefore pre-
vents starting of the vehicle by anyone
who does not have the key.
The ignition key has an electronic chip
which has a special code. When the
ignition is switched on, the code is
recognised and starting is possible.
If the system does not function
correctly, the service warning light
comes on, accompanied by an au-
dible signal and a message on the
multifunction display.
In this case, your vehicle will not
start. Contact a PEUGEOT dealer as
soon as possible.
Lost keys
Visit a PEUGEOT dealer with the ve-
h i c l e ' s V 5 r e g i s t r a t i o n c e r t i fi c a t e a n d
y o u r p e r s o n a l i d e n t i fi c a t i o n d o c u -
ments.
A PEUGEOT dealer will be able to
retrieve the key code and the tran-
sponder code required to order a
replacement key.
Programming the remote
control
Following changing of the remote
control battery or disconnection of
the vehicle battery, the remote con-
trol must be reprogrammed.
Wait at least one minute before
using the remote control.
Switch on the ignition.
Press button B or C for at least
fi v e s e c o n d s w i t h i n t h e n e x t t e n
seconds.
Switch off the ignition.
Wait at least one minute before
using the remote control.
The remote control is now working
again.
Changing the remote control
battery
Battery ref.: CR1620/3 volts.
T h e i n f o r m a t i o n " b a t t e r y fl a t " i s g i v e n
by displaying of the service warning
light, accompanied by an audible
signal and a message on the multi-
function display.
To replace the battery, unclip the casing
using a coin at the notch.
If the remote control does not work
after the battery has been changed,
re-programme the remote control.
Page 72 of 194
4
75
Make a careful note of the
number on each key. The
key number is coded on the
label attached to the key.
If the keys are lost, a PEUGEOT
dealer can rapidly supply you with
new keys.
The high frequency remote con-
trol is a sensitive system; do not
operate it while it is in your pocket
as there is a possibility that it may
unlock your vehicle, without you
being aware of it.
The remote control does not oper-
ate when the key is in the ignition,
even when the ignition is switched
off, except for reprogramming.
Do not operate the deadlocking
function if there is anyone inside
the vehicle.
Driving with the doors locked may
make access to the passenger
compartment by the emergency
s e r v i c e s m o r e d i f fi c u l t i n a n e m e r -
gency.
As a safety precaution (with chil-
dren on board), remove the ignition
key when you leave the vehicle,
even for a short time.
Do not repeatedly press the button
of your remote control out of range
and out of sight of your vehicle.
You run the risk of stopping it from
working and the remote control
would have to be reprogrammed.
When purchasing a second-
hand vehicle, have the key codes
memorised by a PEUGEOT dealer
to ensure that the keys in your
possession are the only ones
which can start the vehicle.
Do not throw the remote
control batteries away, they
contain metals which are
harmful to the environment.
Take them to an approved collection
point.
D o n o t m a k e a n y m o d i fi c a t i o n s t o
the electronic engine immobiliser
system.
Page 73 of 194
4
74
ELECTRONIC ENGINE IMMOBILISER
This locks the engine control system
a few moments after the ignition has
been switched off and therefore pre-
vents starting of the vehicle by anyone
who does not have the key.
The ignition key has an electronic chip
which has a special code. When the
ignition is switched on, the code is
recognised and starting is possible.
If the system does not function
correctly, the service warning light
comes on, accompanied by an au-
dible signal and a message on the
multifunction display.
In this case, your vehicle will not
start. Contact a PEUGEOT dealer as
soon as possible.
Lost keys
Visit a PEUGEOT dealer with the ve-
h i c l e ' s V 5 r e g i s t r a t i o n c e r t i fi c a t e a n d
y o u r p e r s o n a l i d e n t i fi c a t i o n d o c u -
ments.
A PEUGEOT dealer will be able to
retrieve the key code and the tran-
sponder code required to order a
replacement key.
Programming the remote
control
Following changing of the remote
control battery or disconnection of
the vehicle battery, the remote con-
trol must be reprogrammed.
Wait at least one minute before
using the remote control.
Switch on the ignition.
Press button B or C for at least
fi v e s e c o n d s w i t h i n t h e n e x t t e n
seconds.
Switch off the ignition.
Wait at least one minute before
using the remote control.
The remote control is now working
again.
Changing the remote control
battery
Battery ref.: CR1620/3 volts.
T h e i n f o r m a t i o n " b a t t e r y fl a t " i s g i v e n
by displaying of the service warning
light, accompanied by an audible
signal and a message on the multi-
function display.
To replace the battery, unclip the casing
using a coin at the notch.
If the remote control does not work
after the battery has been changed,
re-programme the remote control.