2008 NISSAN ALTIMA HYBRID brake light

Locking the vehicle - Push any door handle Request Switchonce.
 Unlocking thevehicle -Push anydoor handle Request
Switch
once. Thecorresponding doorwillunlock.
Push the door handle Request Switch
again within 5
seconds; all other doors will unlock.
TURNING THE HYBRID SYSTEM ON
 Depress the brake pedal.
 Push the ignition switch to the ON position.
 The READY light will illuminate in the meter.
 Once the READY light is illuminated, you may begin driving
the vehicle even though the engine is not running.
TURNING THE HYBRID SYSTEM OFF
 Shift theselector levertothe P(Park) position andapply
the parking brake.
 Push the ignition switch to turn the Hybrid System off.
INTELLIGENT KEY BATTERY DISCHARGE
If the battery of the Intelligent Key is almost discharged, the
guide light of the Intelligent Key port blinks and the Intelli-
gent Keyinsertion indicator isdisplayed inthe vehicle
information display.
 Tostart theengine, inserttheIntelligent Keyinto thekey
port in the direction indicated until it latches into place.
 To remove theIntelligent Keyfrom theport, push the
ignition switch to turn the engine off and pull the Intelligent Key out of the port.
 The Intelligent Keyport does notcharge theIntelligent Keybattery. Ifyou see thelow
battery indicator, replace the battery in the Intelligent Key.
OPENING THE TRUNK
 Toopen thetrunk, usingtherequest switch,yourIntelligent
Key must be with you.
 Push the request/release switch
under the trunk handle.
 Pull up and out on the handle to open the trunk.
4

CRUISE CONTROL
To activate the cruise control, push the ON/OFF
switch. The indicator light in the instrument panel
will illuminate.
 To set cruising speed,accelerate thevehicle to
the desired speed, push the COAST/SETswitch
and release it. The SET indicator light in the instru-
ment panel will illuminate.
 To reset at a faster cruising speed, push and hold
the ACCEL/RES switch.Whenthevehicle at-
tains the speed you desire, release the switch.
 To reset at a slower cruising speed, push and hold the COAST/SETswitch. Release the
switch when the vehicle slows to the desired speed.
 Tocancel cruisecontrol, pushtheCANCEL switchortap thebrake pedal. TheSET
indicator light in the instrument panel will go out.
 To resume apreset speed, pushandrelease theACCEL/RES switch.Thevehicle
returns to the last set cruising speed when the vehicle speed is over 25 MPH (40 km/h) .
 To turn off cruise control, push the ON/OFFswitch. Both the CRUISE indicator light and
the SET indicator light in the instrument panel will go out.
AUTO CLIMATE CONTROL
AUTO BUTTON
● Press the AUTObutton
. Turn the driver’s side temperature control dialto
the desired temperature. Thiswillallow thefanspeed, airflow distribution and
temperature to be automatically maintained.
● When AUTO is pressed, AUTOwill illuminate. When DUAL
is pressed,DUAL
will illuminate.
● To disable auto mode, press one of the air flow mode control buttons
, turn the
fan speed control dial
or press the front defroster control button.
DRIVER’S SIDE TEMPERATURE CONTROL DIAL
Turn the driver’s temperature control dial left for cold air or right for hot air.
7

ELECTRONICALLY CONTROLLED CONTINUOUSLY VARIABLE
TRANSMISSION (eCVT)
 The eCVT does not produce a gear change sensa-
tion like traditional automatic transmissions.
 Most driving conditions requiredrivinginD(Drive)
range. TheB(Brake) rangecanincrease engine
braking that can be used on long downhill descents.
It can also increase the rate of high voltage battery
charging for short periods of time.
NOTE: Withthetransmission inthe B(Brake) position
and your footoffthe accelerator pedal,engine braking
will be applied.
 When driving in heavy traffic, operate the vehicle in
the D(Drive) position toprevent thehigh voltage
battery from being discharged.
 The transmission in your vehicle requires a special fluid available only at your NISSAN
dealer. No other fluid will meet the exact requirements of the eCVT.
HOMELINK  UNIVERSAL TRANSCEIVER (if so equipped)
SYSTEM OPERATING TIPS
 Garage doors, electrical gates, entry doors, etc. will be activated during programming.
To avoid injury, make sure that people and objects are clear of all doors or gates during
programming. Yourvehicle’s engineshouldbeturned offwhile programming the
HomeLink Transceiver.
 To program your HomeLink Transceiver to operate a garage door, gate, or entry door
opener, home or office lighting, you need to be at the same location as the device.
NOTE: Garage dooropeners (manufactured after1996) have“rolling codepro-
tection”. Toprogram agarage dooropener equipped with“rolling codeprotec-
tion”, you will need to use a ladder to get up to the garage door opener motor to
be able to access the “smart or learn” program button.
PROGRAMMING YOUR HOMELINK  UNIVERSAL TRANSCEIVER (Mirror,
Sun Visor or Overhead Console)
1. To begin, press and hold the two
outer HomeLink buttons (to
clear the memory) until the indi-
cator light blinks slowly (after 20
seconds) . Releasebothbut-
tons.
2. Position theend ofthe hand-
held transmitter 1-3inches
(26-76 mm)away fromthe
HomeLink surface
3. Using bothhands, simultaneously pressandhold both theHomeLink button you
want toprogram andthehand-held transmitter button. DONOT release the
buttons until step 4 has been completed.
15