2008 NISSAN 350Z tow

Mist(MIST)– Lift the lever up for one sweep of the front wipers.
Rear Wipers(REAR)– Twist the end section to operate the first(INT)or second
(ON)speed settings for the rear wipers.
The washer function activates the washer fluid and several sweeps of the wipers:
●For FRONT WASHER, pull lever toward you.
●For REAR WIPER, push lever away from you.
HEADLIGHT AND TURN SIGNAL CONTROL
HEADLIGHT CONTROL SWITCH
Turn the headlight control switchto the
position to turn on the front parking, tail, license plate
and instrument panel lights.
Turn the headlight control switch
to thepo-
sition to turn on the headlights. All other lights remain
on.
FOG LIGHT OPERATION
NOTE: The headlights must be on and the low beams selected for the fog lights to operate.
Turn the switch (inside collar)
to theposition to turn on the fog lights.
Turn the switch (inside collar)
to theOFFposition to turn off the fog lights.
TURN SIGNAL SWITCH
Move the headlight control switch up or downto
signal a turning direction. When the turn is completed,
the turn signals cancel automatically.
To signal a lane change, move the headlight control
switch up or down
to the point where the indica-
tor light begins to flash, but the headlight control switch
does not latch.
HIGH BEAM
Push the headlight control switch forwardto
select the high beam function. The blue
indicator
light illuminates. Pull the headlight switch back to the
original position to select the low beam. The blue
indicator light goes off.
Pull and release the headlight control switch
to flash the headlight high beams on
and off.
3

CRUISE CONTROL (if so equipped)
To activate the cruise control, push theON·OFF
switch. The indicator light in the instrument panel will
illuminate.
To set cruising speed, accelerate the vehicle to the
desired speed, push theCOAST/SETswitch and
release it. The SET indicator light in the instrument
panel will illuminate.
To reset at a faster cruising speed, push and hold the
ACCEL/RESswitch. When the vehicle attains the
speed you desire, release the switch.
To reset at a slower cruising speed, push and hold
theCOAST/SETswitch. Release the switch when
the vehicle slows to the desired speed.
To cancel cruise control, push theCANCELswitch or tap the brake pedal. The SET
indicator light in the instrument panel will go out.
To resume a preset speed, push and release theACCEL/RESswitch. The vehicle
returns to the last set cruising speed when the vehicle speed is over 25 MPH (40 km/h) .
To turn off cruise control, push theON·OFFswitch. Both the CRUISE indicator light and
the SET indicator light in the instrument panel will go out.
SCREW-IN RECOVERY HOOK
Your vehicle is supplied with a screw-in recovery hook
for pulling the vehicle forward. For example: Pulling the
vehicle onto a flat bed for towing.
The screw-in recovery hook tool is located in the right
rear luggage compartment area under the cover along
with the vehicle jack.
To install the recovery hook:
Remove the recovery hook cover from the front grill.
Install the recovery hook as shown in the photo. Turn it
clockwise until securely tightened.
5

FM/AM/XM
RADIO WITH CD CHANGER (if so equipped)
Press and hold theRPTbutton for approximately 2 seconds until the clock display starts
to flash.
Press theSEEK/TRACKbutton to adjust the hours.
Press theTUNE/REW/FFbutton to adjust the minutes.
Press theRPTbutton again to exit the clock set mode.
TRIP COMPUTER
The trip computer may be used to check items such as speed,
outside air temperature, distance to empty (fuel) , average mile-
age and speed, elapsed time and distance traveled. Additionally,
it can function as a stopwatch or be used to operate the RPM
shift feature (REV) (Manual transmission only) .
The twin trip odometer records the distance of individual
trips.
Press the button
to change the display as follows: Trip
A→Trip B→Trip A.
Press and hold the button for more than 1 second to reset
the trip odometer to zero.
TO OPERATE THE TRIP COMPUTER
Turn the ignition switch ON. Then press the side of the buttons.
Press the button
toward the left to scroll through each
mode.
Press the button
toward the left to reset or adjust the various mode selections.
AUTOMATIC TRANSMISSION (if so equipped)
MANUAL SHIFT MODE
When the shift selector lever is shifted from D (Drive)
to the manual shift gate, the transmission enters the
manual shift mode.
In the manual shift mode, shift range is displayed on
the position indicator in the meter.
WHEN SHIFTING UP
Move the shift selector lever to the + (up) side. (Shifts to higher range.)
10

POWER WINDOWS
The power windows operate when the ignition key is in the ON
position, and for about 45 seconds after the ignition key is
turned to the OFF position.
AUTOMATIC ADJUSTING FUNCTION:
The front door power windows have an automatic adjusting
function. This ensures the windows close completely to help
seal against wind noise and weather leaks.
When the front doors are being opened, the windows auto-
matically lower slightly to avoid contact between the windows and the side roof panels.
When the doors are closed, the windows automatically raise slightly.
SECONDARY REAR HATCH RELEASE
Your vehicle is equipped with a secondary rear hatch
release mechanism. This allows opening of the rear
hatch in the event of a discharged battery or in an
emergency.
The secondary rear hatch release is located under
the strut tower bar (Coupe) , or inside the storage
bin compartment (Roadster - upper right side) .
To open the rear hatch from the inside, firmly pull
the release handle to the left towards the passen-
ger side until the lock releases.
MIRROR ADJUSTMENT
The rear view mirror has two pivot points for adjustments. Adjust
the rear view mirror height at the rear pivot and tilt the mirror at the
front pivot. Position the mirror to provide the best visibility through
the rear window.
14

SOFT TOP OPERATION
Before opening or closing your soft top, refer
to the Owner’s Manual for detailed Warnings
and Cautions regarding soft top operation.
Open the top:
1. Make sure the area is clear of ob-
structions and that there is at least 6
feet of clearance above the vehicle.
2. Apply the parking brake and make
sure the transmission is in the P
(Park) position (automatic transmis-
sion) or the N (Neutral) position (manual transmission) .
3. Step on the brake pedal.
4. Start the engine.
5. Push the safety switch (black) located in the center of the top latch lever. Push the top
latch lever (silver) forward to unlatch the top.
6. Press and hold theOPENside of the
soft top operating switch until the
top is fully open and stowed and the
indicator light turns off.
Close the top:
1. Make sure the area is clear of ob-
structions and that there is at least 6
feet of clearance above the vehicle.
2. Apply the parking brake and make
sure the transmission is in the P
(Park) position (automatic transmission) or the
N (Neutral) position (manual transmission) .
3. Step on the brake pedal.
4. Start the engine.
5. Press and hold theCLOSEside of the soft top
operating switch until the top is fully closed and
the indicator light begins to flash.
6. Securely latch the top with the top latch lever.
The indicator light turns off.
If the top does not close when using the operating
switch, refer to the Owner’s Manual for the procedure
to manually close the top.
15