2008 MITSUBISHI LANCER EVOLUTION X light

AUTO-CRUISE CONTROL SYSTEM
ENGINE AND EMISSION CONTROL17-5
CONSTRUCTION AND OPERATIONM2170002000232
SYSTEM OUTLINE
The ECM calculates the auto-cruise control system
operation status when the ECM receives input sig
-
nals from the auto-cruise control switch, vehicle
speed and cancel system [stoplight switch and clutch
switch or transmission range switch ]. The engine control section sends the target acceler
-
ator pedal opening angle value for auto-cruise con-
trol system, the TCM issues a command to transaxle
control , and the gauge issues an ON/OFF
command for the "CRUISE" indicator light.
In the engine control section, the target throttle valve
opening angle value is calculated from the target
accelerator pedal opening angle value for
auto-cruise control system and the actual accelerator
angle value.The vehicle speed is then controlled by
applying the TAC motor.
BLOCK DIAGRAM
Throttle position sensor (TP sensor)Informs the ECM of the throttle valve opening angle.
Transaxle control module (TCM) •Based on the transaxle control signal from the
ECM, it controls the transaxle.
•Outputs the signal from the secondary pulley
speed sensor to the ECM.
•Transmits the selector lever "N" position signal
from the transmission range switch to the ECM.
Vehicle speed sensor Transmits the vehicle speed signal proportional to
the vehicle speed to the ECM.
Component Function
TAC motor Target accelerator
pedal opening
angle signal
Engine control section
Cruise control section"CRUISE" indicator light
AC611103
Actual accelerator
pedal opening
angle signal
Shift control
signal
Target throttle
valve opening
angle signal
Auto-cruise control switch
ECM
Stoplight switch, clutch switch
TCM
"CRUISE"
indicator light
ON/OFF signal
APP sensor
Transmission
range switch
signal Shift control
signal
TransaxleTransmission
range switch
signal
Secondary
pulley speed
sensor signal
ON/OFF
signalON/OFF
signal
Vehicle speed
sensor
Vehicle
speed
signal
Secondary
pulley speed
sensor signal

AUTO-CRUISE CONTROL SYSTEM
ENGINE AND EMISSION CONTROL17-7
FAIL-SAFE FUNCTION
When any of the following conditions are satisfied,
the auto-cruise control system function is stopped
until the system returns to normal. Also, when any of
the conditions are satisfied during the constant
speed driving, the constant speed driving is can
-
celled immediately.
•An abnormality occurs to the auto-cruise control
switch.
•An abnormality occurs to the stoplight switch.
When any of the following conditions are satisfied,
stop the vehicle once and turn the ignition switch to
"LOCK" (OFF). Otherwise, even when the system
returns to normal, the auto-cruise control system
function will continue to be stopped. Also, when any
of the conditions are satisfied during the constant
speed driving, the constant speed driving is can
-
celled immediately.
•ECM abnormality
•TP sensor abnormality
•APP sensor abnormality
.
DIAGNOSIS FUNCTION
•The diagnostic trouble code check is possible
with the "CRUISE" indicator light.
•To facilitate the system check, check the service
data output with the M.U.T.-III.
NOTE: For diagnostic items, service data output
items, and check method, refer to the Service Man
-
ual.

SENSOR
MULTIPORT FUEL SYSTEM (MFI)13A-22
GENERATOR L TERMINAL
After turning on the ignition switch, the current is input by the
ECM to the generator L terminal. This allows the IC regulator to
be on and the field coil to be excited. When the generator
rotates in this situation, the voltage is excited in the stator coil
and the current is output from B-terminal through the commuta
-
tion diode. Also the generated voltage is input to the voltage
regulator through the commutation diode. After the electric gen
-
eration begins, the current is supplied to the field coil from this
circuit. In addition, the generated voltage is output from the
generator L terminal to the ECM. This allows the ECM to detect
that the electric generation begins. The ECM outputs the ON
signal to the combination meter through the CAN and then
turns off the generator malfunction light.
AK602577
L BS
AC
Battery
GeneratorIC regulator Ignition switch-IG
CAN
communication
Generator
malfunction
light
Combination meterECM
Field coil

ACTUATOR
MULTIPORT FUEL SYSTEM (MFI)13A-27
EVAPORATIVE EMISSION VENTILATION
SOLENOID
The evaporative emission ventilation solenoid, an ON/OFF
type solenoid valve, is integrated in the evaporative canis
-
ter.The evaporative emission ventilation solenoid is installed
between the evaporative canister and the air-releasing end,
where the evaporative emission ventilation solenoid takes or
shuts off air.When the current is not flowing through the coil, the
air flows between the nipples, "A" and "B", and through the
evaporative canister.When the current is flowing through the
coil, the air is sealed in the nipple "A" and the air through the
evaporative canister is shut off.When monitoring the evapora
-
tive leak, the ECM turns the evaporative emission ventilation
solenoid on to create the slight vacuum condition in the evapo
-
rative emission control system. The ECM shuts off the air flow-
ing through the evaporative canister to maintain the vacuum
condition necessary for monitoring.
AK604127ABTo canisterConnector
Evaporative
emission
ventilation
solenoid
To filter
AK604554
12
0
AB
OFF
ON ECMECM terminal voltage V
Engine speed r/min From MFI relay
Evaporative emission
ventilation solenoidEngine speed to switch
evaporative emission
ventilation solenoid

GENERATOR CONTROL
MULTIPORT FUEL SYSTEM (MFI)13A-51
GENERATOR CONTROLM2132025000172
During engine idle operation, ECM controls duty of
conduction between generator G terminal and
ground. (G terminal duty is controlled to be the same
as ON duty of the power transistor inside the voltage
regulator). If headlights etc. are turned on while
engine is idling, the consumed current increases
suddenly, but by gradually increasing the generator G terminal OFF duty, ECM restricts sudden increase
in generator's output current and output current is
increased only gradually. (Battery current is supplied
to the headlamp etc. till generator produces sufficient
current.) Thus, ECM prevents change in idle speed
due to sudden increase of engine load.
AK602242 AD
Engine coolant temperature sensor
Generator G terminal
Generator FR terminal
Generator Crankshaft position sensor
A/C switch (CAN)
Ignition switch-STECM

EVAPORATIVE EMISSION CONTROL SYSTEM INCORRECT PURGE FLOW MONITOR
MULTIPORT FUEL SYSTEM (MFI)13A-52
EVAPORATIVE EMISSION CONTROL SYSTEM INCORRECT
PURGE FLOW MONITOR
M2132027200019
The ECM detects whether the fuel vapor leakage
exists or not from the evaporative emission control
system. By the specified pattern within the certain
operation range, the ECM drives the evaporative
emission purge solenoid and the evaporative emis
-
sion ventilation solenoid. This allows slight vacuum
to be produced in the fuel tank.
The ECM measures the vacuum condition through
the fuel tank differential pressure sensor signal. By
comparing the normal (expected) value and the
actual value, the ECM detects whether the fuel vapor
leakage exists or not from the evaporative emission
control system.
AK604139
Evaporative emission
purge solenoid
Evaporative emission
ventilation solenoid
Fuel tank differential pressure sensor
Fuel tank temperature sensor
AB
BatteryMFI relay
ECM Mass airflow sensor
Barometric pressure sensor
Intake air temperature sensor
Engine coolant
temperature sensor
Fuel level sensor (CAN)Fuel
tank
Fuel level
sensor To injector

OIL DIPSTICK, OIL FILLER CAP, OIL DRAIN PLUG
ENGINE LUBRICATION12-4
OIL DIPSTICK, OIL FILLER CAP, OIL DRAIN PLUGM2120007000124
The oil dipstick, oil filler cap, and oil drain plug are
located with serviceability in mind.
OIL PUMPM2120002000077
The oil screen is integrated into the oil pump case to
be compact and lightweight.The oil pump case, which is installed to the bottom of
the ladder flame, is driven by the oil pump chain
through the oil pump sprocket installed to the front of
the oil pump case.
AK503035
Oil drain plug
Engine front
Oil dipstickOil filler cap
AD

INSTRUMENT PANEL AND FLOOR CONSOLE
INTERIOR52A-4
•The decorated panel creating uniformity from the
instrument panel to the door trim has been
adopted.
•The holder in which two cards can be stored has
been installed in the glove box.
•The glove box with damper function has been
installed.
•The center tray for storing small items has been
installed in front of the selector or shift lever cen
-
ter panel.
•The cup holder which can hold two 20-oz bottles
has been equipped. The cup holder can store two
CDs in the upright position and pen-size long
items horizontally.
•Under the arm rest of type B, a large box that can
store 6 CDs has been equipped. (9 CDs for type
C)
•A tray that can store cigarettes and lighters has
been equipped. switch>
•The synthetic cloth is used for the arm rest lid to
enhance luxury and soft feelings.