2008 MITSUBISHI LANCER EVOLUTION X weight

GENERAL INFORMATION
FUEL SUPPLY13B-2
GENERAL INFORMATIONM2134000100833.The fuel system consists of the following compo-
nents:
•Fuel injector
•Fuel rail
•Fuel pipe
•Fuel tank
•Fuel pump module
•Evaporative emission canister
SPECIFICATIONS
CONSTRUCTION DIAGRAM
This fuel system is designed with consideration for
global environment protection to ensure safety at a
collision, reduce weight, and improve reliability and
quality. This system has the following features:
•A quick-joint connector of a plastic tube is used
for the fuel high-pressure hoses in the engine
compartment to reduce the permeation of fuel
evaporative emission.
•The surface of underfloor fuel pipes is coated
with 1-mm thickness of plastic to improve resis
-
tance to corrosion and chipping.
•A returnless fuel system eliminates returned fuel
from the engine. The heat that fuel receives from
the engine is reduced, minimizing fuel tempera
-
ture in the fuel tank and controlling the amount of
evaporated gas.
ItemSpecification
Fuel tank capacity dm3 (gal)59 (15.5)
Fuel pump typeElectric
Fuel filter typeCartridge (incorporates fuel pump module)
Fuel return systemReturnless
Fuel pump pressure regulator pressure kPa (psi)324 (46)
Fuel injectorTy p eElector-magnetic
Quantity4
Evaporative emission control systemCanister
AC610224
Fuel rail
Fuel injector
Fuel pipeFuel pump moduleEvaporative
emission
canister Fuel tank
AB

OIL DIPSTICK, OIL FILLER CAP, OIL DRAIN PLUG
ENGINE LUBRICATION12-4
OIL DIPSTICK, OIL FILLER CAP, OIL DRAIN PLUGM2120007000124
The oil dipstick, oil filler cap, and oil drain plug are
located with serviceability in mind.
OIL PUMPM2120002000077
The oil screen is integrated into the oil pump case to
be compact and lightweight.The oil pump case, which is installed to the bottom of
the ladder flame, is driven by the oil pump chain
through the oil pump sprocket installed to the front of
the oil pump case.
AK503035
Oil drain plug
Engine front
Oil dipstickOil filler cap
AD

GENERAL INFORMATION
FRONT AXLE26-2
GENERAL INFORMATIONM2260000100819
For the front axle, a double-row angular contact ball
bearing with an integral oil seal is adopted as a
wheel bearing, and EBJ-ETJ type constant velocity
joint as a driveshaft.
It has the following features:
•The driveshaft incorporates lightweight and com-
pact EBJ-ETJ type constant velocity joints.
•Lead-free grease for the constant velocity joint is
adopted.
•Hexavalent chromium is eliminated from the dust
cover material.
•The number of parts is reduced by integrating the
magnetic encoder for ABS wheel speed detection
into the wheel bearing.
NOTE: .
ETJ (High Efficiency Compact Tripod Joint): the
lighter and smaller constant velocity joint com
-
pared with the conventional TJ has been
installed.
EBJ (High Efficiency Compact Birfield Joint): the
lighter and smaller constant velocity joint com
-
pared with the conventional BJ has been
achieved by adopting the eight small balls.
SPECIFICATIONS
NOTE: *: Indicates the distance between each joint
center.
ItemSpecification
Wheel bearingBearing typeUnit bearing (double-row angular contact ball
bearing)
Bearing (Outer diameter x inside
diameter) mm (in)80 × 43 (3.15 × 1.69)
DriveshaftJoint typeOutsideEBJ
InsideETJ
Shaft length* x shaft
diameter mm (in)M/T-LH380.5 × 24.5 (15.0 × 1.0)
M/T-RH715 × 28 (28.1 × 1.1)
CVT-LH399.5 × 24.5 (15.7 × 1.0)
CVT-RH715.0 × 28 (28.1 × 1.1)

OIL RESERVOIR
POWER STEERING37-8
OIL RESERVOIRM2370005000376
The resin oil reservoir is used to reduce weight. The oil reser-
voir is translucent and has fluid level marks (MAX and MIN
lines), facilitating inspection.
AC200365 AC
Scale
Cap
O-ring
Filter Oil reservoir
Return
Suction