2008 MITSUBISHI GRANDIS fuel consumption

3-16 Instruments and controls
3
NOTE●The display unit (ex. km or mile) and brightness can be changed as desired. (Refer to “ Display brightness adjustment” on page
3-27 and “Display unit selection” on page 3-29.) When the system cannot provide a definite value for momentary fuel con-
sumption/average fuel consumption/driving range/average speed, it is displayed as “---”.
●The figure of the display varies according to the conditions under which a vehicle is travelling (road conditions, the manner in
which the vehicle is being driven, etc.).
Observe display for reference because the figure of the display may differ from the actual figure.A- Outside temperature → p. 3-20
B- Driving information → p. 3-21
C- Digital clock → p. 3-17
BK-XP08E1ENUK.en-uk.book Page 16 Monday, August 13, 2007 2:20 PM

Instruments and controls
3-21
3
NOTE●The outside temperature can be displayed from -40 °C to
50 °C.
●The outside temperature displayed may differ from the
actual temperature on account of surrounding conditions,
driving conditions, etc.
●When the outside temperature is below -40 °C or over
50°C, the display will remain -40 °C or 50 °C.
Driving information
E00509000041
For vehicles with MITSUBISHI MOTORS genuine
audioThe momentary fuel consumption, average fuel consumption,
driving range and average speed can be displayed.
When the ignition switch is turned “ON”, the display shows the
4 items sequentially and returns to the original display that is
shown before the ignition switch was last turned “OFF”.NOTE●If the “DISP” button is pressed while the display is scroll-
ing through the sequence mentioned above, the display
stops scrolling and shows the item that was shown before
the ignition switch was last turned to the “OFF” position.Except for vehicles with MITSUBISHI MOTORS genu-
ine audioOnly the momentary fuel consumption can be displayed. Refer
to “Momentary fuel consumption” on page 3-22.
BK-XP08E1ENUK.en-uk.book Page 21 Monday, August 13, 2007 2:20 PM

3-22 Instruments and controls
3
Change of driving information (For vehicles with MIT-
SUBISHI MOTORS genuine audio)
E00509100068
Every time the “DISP” button is pressed lightly (less than
5 seconds), the display can be changed.
Momentary fuel consumption → Average fuel consumption →
Driving range → Average speed
Momentary fuel consumption
E00509200014
This value shows the momentary fuel consumption (in
L/100km, km/L or mpg). Calculation and indication of the
value begin when the vehicle speed rises above
6km/h(4mph).
BK-XP08E1ENUK.en-uk.book Page 22 Monday, August 13, 2007 2:20 PM

Instruments and controls
3-23
3
Average fuel consumption
E00509300060
This value shows the average fuel consumption (in L/100 km,
km/L or mpg).NOTE●When the ignition switch is turned on, the average fuel
consumption which was being displayed when the igni-
tion switch was previously turned off will be displayed
once again.
●Average fuel consumption varies according to the condi-
tions under which a vehicle is travelling (road conditions,
the manner in which the vehicle is being driven, etc.).
Observe this display for reference because the fuel con-
sumption display may differ from the actual fuel con-
sumption.To r e s e t t h e d i s p l a y
You can switch from the automatic reset mode to the manual
reset mode by performing the following operations:
1. Press and hold down button (A), then press the “SET”
button (B) within 1 second, and a buzzer will sound and
the reset mode will be changed.
BK-XP08E1ENUK.en-uk.book Page 23 Monday, August 13, 2007 2:20 PM

Instruments and controls
3-25
3
●Automatic reset mode
When 4 hours have passed after the ignition switch is
turned to the “OFF” or “ACC” position, the display is
automatically reset. It then shows “---”.
●Manual reset mode
If you reset the display at the time when you want to start
the measurements, average fuel consumption from that
point of time can be displayed.
Push the “DISP” button for more than 5 seconds.NOTE●While the ignition switch is in the “ON” position, the
automatic reset mode is permanently selected. If you wish
to make continuous measurements, select the manual
mode.
Driving range
E00509400016
This value shows the distance (in km or miles) that can be
driven on the fuel remaining in the fuel tank.
BK-XP08E1ENUK.en-uk.book Page 25 Monday, August 13, 2007 2:20 PM

3-26 Instruments and controls
3
NOTE●If the driving range drops below 50 km (30 miles) while
the driving range is displayed, the display shows “---”.
When this occurs, top up the fuel tank as soon as possible.
●The driving range varies depending on road conditions,
the manner of driving and other related factors. Conse-
quently, the display should be used only as a guide. It is
recommended to add fuel as soon as the low fuel warning
lamp in the instrument cluster illuminates.
(Refer to “Low fuel warning lamp” on page 3-6.)
●Refueling will update the driving range indication.
●The driving range displayed is based on previous fuel con-
sumption data. Disconnecting the battery cable will result
in the deletion of existing fuel consumption data, which
will affect the unit’s calculations.
●The driving range figure can occasionally increase if the
vehicle is stopped on an incline. This is because the fuel
has moved in the tank because of the incline and is not
considered as a fault.
Average speed
E00509500062
This value shows the average speed (in km/h or mph) since the
display was reset. Refer to “To reset the display” on page 3-23.
BK-XP08E1ENUK.en-uk.book Page 26 Monday, August 13, 2007 2:20 PM

Instruments and controls
3-29
3
Display unit selection
E00509700051
It is possible to change the units in which distance, fuel con-
sumption, and time are displayed.NOTE●Except for vehicles with MITSUBISHI MOTORS genu-
ine audio, only the unit of momentary fuel consumption
can be changed to km or miles.
1. Press and hold down button (A), then press the “M” but-
ton (B) within 1 second. A buzzer will sound, and the sys-
tem will allow units to be changed.2. Use the “H” button (C) or “M” button (B) to select the
desired speed unit, then press the “SET” button (D) to
enter the setting.
H - km
M - mile
BK-XP08E1ENUK.en-uk.book Page 29 Monday, August 13, 2007 2:20 PM

3-30 Instruments and controls
3
3. If the km unit was selected in step 2, the fuel consumption
unit must be subsequently selected using the “H” button
(C) or “M” button (B).
Use the “H” button (C) or “M” button (B) to select the
desired fuel consumption unit, then press the “SET” but-
ton (D) to enter the setting.4. When you have finished setting the fuel consumption unit
(or if you selected miles in step 2), the system will require
you to proceed to select, using the “H” button (C) or “M”
button (B), whether times should be displayed in the
12-hour format or in the 24-hour format. The currently
selected format will be displayed.H - L/100km
M - km/LBK-XP08E1ENUK.en-uk.book Page 30 Monday, August 13, 2007 2:20 PM