2008 MITSUBISHI GRANDIS clock

4 General information
3. Open the fuel tank filler tube by slowly turning the cap
anticlockwise.
RHD
A- Remove
B- Close
CAUTION
!●Since the fuel system may be under pressure,
remove the fuel tank filler tube cap slowly. This
relieves any pressure or vacuum that might have
built up in the fuel tank. If the cap is venting vapour
or if you hear a hissing sound, wait until it stops
before removing the cap. Otherwise, fuel may spray
out, injuring you or others.
BK-XP08E1ENUK.en-uk.book Page 4 Monday, August 13, 2007 2:20 PM

General information
5
4. To fill with fuel correctly depends mainly on correct han-
dling of the fuel filler gun. Do not tilt the gun. Insert the
gun in the tank port as far as it goes.
5. When the gun stops automatically, remove the gun half
the way in the tank port. After the second automatic stop,
do not fill with fuel any more.
6. To close, turn the fuel tank filler tube cap slowly clock-
wise until you hear clicking sounds, then gently push the
fuel tank filler door closed.
Installation of accessories
E00200300745
We recommend you to consult your MITSUBISHI MOTORS
Authorized Service Point.
●The installation of accessories, optional parts, etc., should
only be carried out within the limits prescribed by law in
your country, and in accordance with the guidelines fitting
instructions and warnings contained within the documents
accompanying the parts or accessories.
●Improper installation of electrical components may cause
an electrical fire if incorrectly fitted. Please refer to the
Modification/alteration to the electrical or fuel systems
section within this owner’s manual.
●Using a cellular phone or radio set inside the vehicle with-
out an external antenna may cause electrical system inter-
ference, which could lead to unsafe vehicle operation.
●Tyres and wheels which do not meet specifications must
not be used.
Refer to the “Specifications” section for information
regarding wheel and tyre sizes.
CAUTION
!●A label which reads “UNLEADED FUEL ONLY” is
attached to the fuel tank filler lid of vehicles which
can only operate using unleaded petrol. Serious
engine and catalytic converter damage will result if
leaded petrol is filled into these vehicles, and conse-
quently, this must never be attempted.
CAUTION
!●To avoid fuel spillage and overfilling, do not “top-
off” the fuel tank.
CAUTION
!●If you need to replace the fuel tank filler tube cap,
use only the cap specified for your model vehicle.
BK-XP08E1ENUK.en-uk.book Page 5 Monday, August 13, 2007 2:20 PM

Instruments and controls
3-15
3 Multi centre display
E00503600120
When the ignition switch is in the “ACC” position, the digital
clock is displayed in the multi centre display. When the igni-
tion switch is in the “ON” position, the momentary fuel con-
sumption and outside temperature are displayed besides the
digital clock.
WARNING
!●When operating the system for a prolonged period,
make sure the vehicle is parked in a well ventilated
area to avoid the accumulation of toxic fumes inside
and outside of the passenger compartment.
CAUTION
!●The driver should not operate the display while the
vehicle is in motion.●When operating the system, stop the vehicle in a safe
area.
BK-XP08E1ENUK.en-uk.book Page 15 Monday, August 13, 2007 2:20 PM

3-16 Instruments and controls
3
NOTE●The display unit (ex. km or mile) and brightness can be changed as desired. (Refer to “ Display brightness adjustment” on page
3-27 and “Display unit selection” on page 3-29.) When the system cannot provide a definite value for momentary fuel con-
sumption/average fuel consumption/driving range/average speed, it is displayed as “---”.
●The figure of the display varies according to the conditions under which a vehicle is travelling (road conditions, the manner in
which the vehicle is being driven, etc.).
Observe display for reference because the figure of the display may differ from the actual figure.A- Outside temperature → p. 3-20
B- Driving information → p. 3-21
C- Digital clock → p. 3-17
BK-XP08E1ENUK.en-uk.book Page 16 Monday, August 13, 2007 2:20 PM

Instruments and controls
3-17
3
Digital clock
E00503700118
Following modes are available for digital clock adjustment:
●For vehicles with MITSUBISHI MOTORS genuine audio
automatic mode and manual mode
●Except for vehicles with MITSUBISHI MOTORS genu-
ine audio manual mode onlySelect the automatic mode or the manual mode by performing
the following operations:
1. Enter the function setup mode by pushing the “MENU”
button.
BK-XP08E1ENUK.en-uk.book Page 17 Monday, August 13, 2007 2:20 PM

3-18 Instruments and controls
3
2. Press the “MENU” button repeatedly to select the CT
(Clock Time) mode.
The order is: AF → CT → REG → TP-S → PH → MUTE
(with PH OFF, this mode is not displayed) → Language of
PTY display → Function setup mode OFF
(Refer to “Function setup mode” on page 5-35.)
NOTE●Although “PH” and “MUTE” appear on the display, the
PH and MUTE functions are inoperative.
BK-XP08E1ENUK.en-uk.book Page 18 Monday, August 13, 2007 2:20 PM

Instruments and controls
3-31
3
Use the “H” button (C) or “M” button (B) to choose your
desired time display format, and then press the “SET” but-
ton (D) to enter the setting.5. The display will return to the original display item.
NOTE●If you selected the mile unit in step 2, the speed and fuel
consumption units will be as follows.
• Speed: mph (miles per hour)
• Fuel consumption: mpg (miles per gallon)
●To cancel the unit setting procedure before completion,
press the button (A).
●The outside temperature and digital clock are not shown
during the unit selecting procedure.
●If the “SET” button is not pressed for about 15 seconds or
longer in the middle of the selection, the currently
selected unit is set automatically. Then, the display returns
to the original display item.
H - 12-hour format
M - 24-hour format
BK-XP08E1ENUK.en-uk.book Page 31 Monday, August 13, 2007 2:20 PM

5-8 For pleasant driving
5
NOTE●There is a photo sensor (F) and interior air temperature
sensor (G) inside the vehicle.
Never place anything on top of these sensors, since doing
so will prevent them from functioning properly.
Blower speed selection dial
E00702800127
Select the blower speed by turning the blower speed selection
dial clockwise or anticlockwise.
The blower speed will gradually increase as the dial is turned
to the right.
When the blower speed selection dial is set to the “OFF” posi-
tion, all fan-driven airflow will stop.
F- Photo sensor*
G- Interior air temperature sensor
BK-XP08E1ENUK.en-uk.book Page 8 Monday, August 13, 2007 2:20 PM