2008 MITSUBISHI COLT crank position

3-12 Instruments and controls
3
Charge warning lampE00502700036
This lamp illuminates when the ignition switch
is turned to the “ON” position, and the lamp goes
off after the engine has started.
In the event of a fault in the charging system, the
warning lamp comes on and a buzzer sounds.
Oil pressure warning lampE00502800053
This lamp illuminates when the ignition switch
is turned to the “ON” position, and the lamp goes
off after the engine has started. If it illuminates
and a buzzer sounds while the engine is running,
the oil pressure is too low.
If the warning lamp illuminates while the engine
is running, turn the engine off and have it
inspected.
NOTE● The oil pressure warning lamp should not
be treated as an indi cation of the engine’s
oil level. The oil level must be checked
using the dipstick.
CAUTION!
● If the warning lamp illuminates and a
buzzer sounds while the engine is run-
ning, there is a problem in the charg-
ing system. In this case, immediately
park your vehicle in a safe place and
we recommend you to have it checked.
CAUTION!
●If this lamp illum inates when the
engine oil level is not low, have it
inspected.
● This warning lamp does not indicate
the amount of oil in the crankcase.
This must be determined by checking
the oil level on the dipstick, while the
engine is switched off.
● If you continue driving with low engine
oil level or with this warning lamp illu-
minated, engine seizure may occur.

4-18 Starting and driving
4
6. Turn the ignition key to the “ON” position and make cer-tain that all warning lamps are functioning properly before
starting the engine.
7. Turn the ignition key to the “START” position without depressing the accelerator pedal, and release it when the
engine starts.
NOTE● A ticking noise may be heard after starting the engine.
This is not an abnormal condition. The noise will disap-
pear after a short time of engine running.
If the ticking noise continues after the engine has warmed
up, we recommend that you have your vehicle checked.
● If the engine won’t start, depress the accelerator pedal
fully while cranking the engi ne. Once the engine starts,
release the accelerator pedal. Vehicles with automated manual transmission
1. Insert the ignition key and fasten the seat belt.
2. Make sure the parking brake is applied.
3. Depress and hold the brake pedal.
4. Turn the ignition key to the “ON” position and make cer- tain that all warning lamps are functioning properly.
5. Place the allshift lever in the “N” (Neutral) position and confirm that “N” is shown by the allshift indicator display.
Refer to “Moving the allshift lever” on page 4-27.
CAUTION!
● When starting the engine, make sure you depress
the brake pedal. If you st art the engine with the
accelerator pedal depressed, move your foot to the
brake pedal as soon as the engine has started.

Starting and driving4-19
4
6. Turn the ignition key to the “START” position withoutdepressing the acceler ator pedal, and release it when the
engine starts.
NOTE● For safety, the vehicle is designed so that the engine will
not start unless the allshift lever is in the “N” (Neutral)
position. Place the allshift leve r in the “N” (Neutral) posi-
tion before starting the engine.
● If you turn the ignition key to the “START” position when
the gearshift is not in the “N” (Neutral) position, the
allshift indicator display will behave as follows to indicate
that the engine will not start.
• Gearshift in “S” (Stand by) position: An “A” or “1” will
flash several times.
• Gearshift in “R” (reverse) position: An “R” will flash
several times.
Confirm that “N” is shown by the allshift indicator dis-
play.
● If the engine won’t start, depress the accelerator pedal
fully while cranking the engi ne. Once the engine starts,
release the accelerator pedal.
Starting the engine (diesel-powered vehicles)E00601800073
Vehicles with manual transmission 1. Insert the ignition key and fasten the seat belt.
2. Make sure the parking brake is applied.
3. Depress and hold the brake pedal.
4. Fully depress the clutch pedal.
5. Place the gearshift lever in the “N” (Neutral) position.
CAUTION!
●When starting the engine, make sure you depress
the brake pedal. If you start the engine with the
accelerator pedal depressed, move your foot to the
brake pedal as soon as the engine has started.