2008 MITSUBISHI COLT engine

For emergencies6-5
66. Start the engine in the vehicle which has the booster bat-tery, let the engine idle a few minutes, then start the
engine in the vehicle with the discharged battery. 7. After the engine has started, disconnect the leads in the
reverse order.
● Make sure that the conn ection is made to the
appointed position (shown in the illustration). If the
connection is made directly to the negative side of
the battery, the inflammable gases generated from
the battery might catch fire and explode.
● When connecting the jump lead, do not connect the
positive (+) cable to the ne gative (-) terminal. Other-
wise sparks might cause the battery to explode.
CAUTION!
●Use care not to get the jump lead caught in the cool-
ing fan or other rotating part in the engine compart-
ment.
● Use the proper leads suitable for the battery size.
Otherwise heat damage to the cables could result.
●Check the jump leads for damage and corrosion
before use.
CAUTION!
●Keep the engine of the ve hicle giving assistance run-
ning.
WARNING!
WARNING!
● Charging the battery while it is installed in the vehi-
cle might cause the battery to catch fire and explode.
Or damage to the vehicle could result. If it has to be
charged in this condition for unavoidable reasons,
disconnect the vehicle side negative (-) terminal con-
nected to the battery.
● Keep sparks, cigarettes an d flames away from the
battery because the battery may produce an explo-
sion.
● Use adequate ventilation when charging or using the
battery in an enclosed space.
●Remove all the caps before charging the battery.
●Electrolyte is corrosive, diluted sulphuric acid.
If electrolyte (battery ac id) comes into contact with
your hands, eyes, clothes or the painted surface of
your vehicle, it should be thoroughly flushed with
water. If electrolyte gets into your eyes, flush them
with water immediately and thoroughly, and get
prompt medical attention.

6-6 For emergencies
6
NOTE●If the vehicle is put in motion without fully charging the
battery, it might cause the loss of smooth engine operation
and the anti-lock brake warning lamp to illuminate.
Refer to “Anti-lock brake system (ABS)” on page 4-36.
Engine overheating
E00800601321
If the high coolant temperature warning lamp flashes while the
engine is running, the engine may be overheating. If this
occurs, take the follow ing corrective measures:
1. Stop the vehicle in a safe place.
2. Check whether steam is comin g from the engine compart-
ment.
[If there is no steam comi ng from the engine compart-
ment]
With the engine still running, raise the bonnet to ventilate
the engine compartment.
[If steam is coming from the engine compartment]
Stop the engine, and when the steam stops, raise the bon-
net to ventilate the engine compartment. Restart the
engine.
CAUTION!
● Do not attempt to start the engine by pulling or
pushing the vehicle.
It could damage your vehicle.
●Always wear protective eye goggles when working
near the battery.
●Keep the battery out of reach of children.
WARNING!
●Do not open the bonnet wh ile steam is coming from
the engine compartment. It could cause steam or hot
water to spurt out, causin g burns. Hot water could
spurt out even when there is no steam coming out,
and some parts will be very hot. Be very careful
when opening the bonnet.
●Be careful of hot steam, which could be blowing off
the reserve tank cap.
●Do not attempt to remove the radiator cap (petrol-
powered vehicles) or res erve tank cap (diesel-pow-
ered vehicles) while the engine is hot.

For emergencies6-7
6
3. Confirm that the cooling fan is turning. If the fan is notturning, stop the engine im mediately and have it checked.
4. After the high coolant temp erature warning lamp has gone
off, stop the engine.
A- Cooling fan B- Radiator cap
C- Reserve tank * : Front of the vehicle
Petrol-powered vehicles
Diesel-powered vehicles
WARNING!
●Be careful not to get your hands or clothes caught in
the cooling fan.

For emergencies6-9
6
Petrol-powered vehicles with turbocharger
The reserve tank lid is equipped with a dipstick.
Remove the dipstick and wipe it with a clean cloth. Rein-
sert the dipstick as far as it will go. Remove the dipstick
and read the coolant level, which should always be within
the range “F” (FULL) or “L” (LOW). 6. Add coolant to the radiator
and/or reserve tank if neces-
sary (refer to the “Maintenance” section).
7. Examine the radiator hoses for coolant leakage and the drive belt for looseness or damage.
If there is anything wrong with the cooling system or
drive belt, we recommend that you have it checked and
repaired.
WARNING!
● If there is none, make sure that the engine has
cooled down before removi ng the radiator cap (B)
(petrol-powered vehicles) or reserve tank cap (C)
(diesel-powered vehicles), because hot steam or boil-
ing water otherwise will gush from the filler port
and may scald you.
FULL
LOW
CAUTION!
● Do not add coolant while the engine is hot. Suddenly
adding cold coolant coul d damage the engine. Wait
for the engine to cool down, then add coolant a little
at a time.

6-36 For emergencies
6To w i n g
E00801501705
If your vehicle needs to be towed
If towing is necessary, we recommend that you have it done by
your MITSUBISHI MOTORS Authorized Service Point or a
commercial tow truck service.
In the following case, transport the vehicle using a tow truck.
● The engine runs but the vehicle does not move or abnor-
mal noise is produced.
● Inspection of the vehicle’s u nderside reveals that oil or
some other fluid is leaking.
If a wheel gets stuck in a ditch, do not try to tow the vehicle.
Please contact your MITSUBISHI MOTORS Authorized Serv-
ice Point or a commercial to w truck service for assistance.
Only when you cannot receive a towing service from a
MITSUBISHI MOTORS Authorized Service Point or com-
mercial tow truck service, tow y our vehicle carefully in accord-
ance with the instructions given in “Emergency towing” in this
part.
The regulations concerning towing may differ from country to
country. It is recommended th at you comply with the regula-
tions of the area where you are driving your vehicle.

For emergencies6-37
6
Towing the vehicle by a tow truck
Towing with rear wheels off the ground (Type B)
Place the gearshift lever (manual transmission) or the allshift
lever (automated manual transm ission) in the “N” (Neutral)
position. With a vehicle that has an automated manual trans-
mission, confirm that the transm ission is in the “N” (Neutral)
position by checking that “N” is shown by the allshift indicator
display and by pushing the vehicle.
Turn the ignition key to the “ACC” position and secure the
steering wheel in a straight ah ead position with a rope or tie-
down strap. Never place the igni tion key in the “LOCK” posi-
tion when towing.
If, with a vehicle that has an automated manual transmission,
the engine will not start and the transmission is not in the “N”
(Neutral) position, press the brake pedal, turn the ignition
switch to the “ON” position, and move the allshift lever to the
“N” (Neutral) position.
Towing with front wheels off the ground (Type C)
Release the parking brake.
Place the gearshift lever (manual transmission) or the allshift
lever (automated manual transm ission) in the “N” (Neutral)
position. With a vehicle that has an automated manual trans-
mission, confirm that the transmi ssion is in the “N” (Neutral)
position by checking th at “N” is shown by the allshift indicator
display and by pushing the vehicle.
If, with a vehicle that has an automated manual transmission,
the engine will not start and th e transmission is not in the “N”
(Neutral) position, press the brake pedal, turn the ignition
switch to the “ON” position, and move the allshift lever to the
“N” (Neutral) position.
CAUTION!
● This vehicle must not be towed by a tow truck using
sling lift type equipment (Type A) as illustrated.
Using a sling lift will da mage the bumper and front
end.
● If the transmission is malfunctioning or damaged,
transport the vehicle with the driving wheels on a
carriage (Type C, D or E) as illustrated.
●If your vehicle has an automated manual transmis-
sion, place the a llshift lever in the “N” (Neutral)
position before stopping the engine.
CAUTION!
● [For vehicles with the traction control system
(TCL)/active stability control system (ASC)]
If the vehicle is towed with the ignition switch in the
“ON” position and only th e front wheels or only the
rear wheels raised off the ground, the traction con-
trol system (TCL) may operate, resulting in an acci-
dent.
Refer to “Traction control system (TCL)/Active sta-
bility control system (ASC)” on page 4-42.

6-38 For emergencies
6
Emergency towing
If a towing service is not available in an emergency, your vehi-
cle may be temporarily towed by a rope secured to the towing
hook.
If your vehicle is to be towed by another vehicle or your vehi-
cle tows another vehicle, pay car eful attention to the following
points.
If your vehicle is to be towed by another vehicle
1. Take out the towing hook and wheel nut wrench (if so
equipped). (Refer to “Tools, jack and tyre repair kit” on
page 6-10.)
CAUTION!
● If your vehicle has an automated manual transmis-
sion, place the allshift le ver in the “N” (Neutral)
position before stopping the engine.

6-40 For emergencies
6
4. Secure the tow rope to the front towing hook.
NOTE●To avoid deforming or otherwise damaging the vehicle
body when hooking the rope onto the towing hook,
observe the following instructions:
• Mount the towing hook securely.
• Do not attach the rope to any part of the vehicle other
than the towing hook.
• Do not drive in a way that subjects the towing hook to significant physical shock. 5. Keep the engine running.
If the engine is not running, turn the ignition key to the
“ACC” or “ON” position to unlock the steering wheel.
6. Place the gearshift lever (m anual transmission) or the
allshift lever (automated manual transmission) in the “N”
(Neutral) position.
With a vehicle that has an automated manual transmis-
sion, confirm that the transmi ssion is in the “N” (Neutral)
position by checking that “N ” is shown by the allshift
indicator display and by pushing the vehicle.
If, with a vehicle that has an automated manual transmis-
sion, the engine will not start and the transmission is not
in the “N” (Neutral) position, press the brake pedal, turn
the ignition switch to the “ON” position, and move the
allshift lever to the “N” (Neutral) position.
7. Turn on the hazard warning lamps if required by law. (Follow the local driving laws and regulations.)
CAUTION!
● Do not tow the vehicle with the rope at an excessive
diagonal angle.
5-door models
CAUTION!
● When the engine is not running, the brake booster
and power steering do no t operate. This means
higher brake depression force and higher steering
effort are required. Therefore, vehicle operation is
more difficult than usual.
● Do not leave the key in the “LOCK” position or do
not remove the ignition key from the ignition switch
while driving. The steering wheel will lock, causing
loss of control.