2008 MITSUBISHI COLT display

3-18 Instruments and controls
3
3. Make your selection by pressing the “ ” button or the“ ” button.
NOTE● After selecting a mode, you can leave the function setup
mode by taking either of the following steps: • Press the “MENU” button for at least 2 seconds.
• Make no entry for 7 seconds.
Automatic mode (For ve hicles with MITSUBISHI
MOTORS genuine audio)
The automatic mode can set the local time automatically by
using the signal from the local RDS stations. In this mode, CT
(A) is shown in the display. Refer to “Radio data system
(RDS)” on page 5-32, 5-32.
- CT ON (Automatic mode)
- CT OFF (Manual mode)

3-20 Instruments and controls
3
NOTE●The outside temperature can be displayed from -40 °C to
50 °C.
● The outside temperature displayed may differ from the
actual temperature on account of surrounding conditions,
driving conditions, etc.
● When the outside temperatur e is below -40 °C or over
50 °C, the display will remain -40 °C or 50 °C.Driving informationE00509000054
For vehicles with MITSUBISHI MOTORS genuine
audio
The momentary fuel consumption, average fuel consumption,
driving range and average speed can be displayed.
When the ignition switch is turn ed “ON”, the display shows the
4 items sequentially and returns to the original display that is
shown before the ignition switch was last turned “OFF”.
NOTE● If the “DISP” button is pressed while the display is scroll-
ing through the sequence mentioned above, the display
stops scrolling and shows the item that was shown before
the ignition switch was last turned to the “OFF” position.
Except for vehicles with MITSUBISHI MOTORS
genuine audio
Only the momentary fuel consumption can be displayed. Refer
to “Momentary fuel consumption” on page 3-21.

Instruments and controls3-21
3
Change of driving information
(For vehicles with MITSUBISHI MOTORS genuine
audio)
E00509100055
Every time the “DISP” button is pressed lightly (less than 5
seconds), the display can be changed.
Momentary fuel consumption → Average fuel consumption →
Driving range → Average speed
Momentary fuel consumptionE00509200030
This value shows the momentary fuel consumption (in
L/100km, km/L or mpg). Calculation and indication of the
value begin when the vehicle speed rises above 6 km/h (4
mph).

3-22 Instruments and controls
3
Average fuel consumptionE00509300057
This value shows the average fuel consumption (in L/100km,
km/L or mpg).
NOTE●When the ignition switch is turned on, the average fuel
consumption which was being displayed when the igni-
tion switch was previously turned off will be displayed
once again.
● Average fuel consumption va ries according to the condi-
tions under which a vehicle is travelling (road conditions,
the manner in which the vehicle is being driven, etc.).
Observe this display for reference because the fuel con-
sumption display may differ from the actual fuel con-
sumption. To reset the display
You can switch from the automa
tic reset mode to the manual
reset mode by performing the following operations:
1. Press and hold down button (A), then press the “SET” button (B) within 1 second, and a buzzer will sound and
the reset mode will be changed.

Instruments and controls3-23
3
2. The name of the newly selected mode will flash, then thedisplay will return to its original indications. 3. The status of the selected mo
de will be shown on the dis-
play.
1- Automatic reset mode
2- Manual reset mode
or

3-24 Instruments and controls
3
●Automatic reset mode
When 4 hours have passed after the ignition switch is
turned to the “OFF” or “ACC” position, the display is
automatically reset. It then shows “---”.
● Manual reset mode
If you reset the display at the time when you want to start
the measurements, average fu el consumption from that
point of time can be displayed.
Push the “DISP” button for more than 5 seconds.
NOTE● While the ignition switch is in the “ON” position, the
automatic reset mode is perm anently selected. If you wish
to make continuous measur ements, select the manual
mode.
Driving rangeE00509400045
This value shows the distance (in km or miles) that can be
driven on the fuel remaining in the fuel tank.

Instruments and controls3-25
3
NOTE●If the driving range drops below 50 km (30 miles) while
the driving range is displaye d, the display shows “---”.
When this occurs, top up the fu el tank as soon as possible.
● The driving range varies depending on road conditions,
the manner of driving and other related factors. Conse-
quently, the display should be used only as a guide. It is
recommended that you add fuel as soon as the low fuel
warning lamp in the instrument cluster illuminates.
(Refer to “Low fuel warning lamp” on page 3-6.)
● Refueling will update the driving range indication.
● The driving range displayed is based on previous fuel con-
sumption data. Disconnecting the battery cable will result
in the deletion of existing fuel consumption data, which
will affect the unit’s calculations.
● The driving range figure can occasionally increase if the
vehicle is stopped on an inclin e. This is because the fuel
has moved in the tank because of the incline and is not
considered to be a fault.
Average speedE00509500059
This value shows the average speed (in km/h or mph) since the
display was reset. Refer to “To reset the display” on page 3-22.

3-26 Instruments and controls
3
●Automatic reset mode
When 4 hours have passed after the ignition switch is
turned to the “OFF” or “ACC” position, the display is
automatically reset. It then shows “---”.
● Manual reset mode
If you reset the display at the time when you want to start
the measurements, average speed from that point of time
can be displayed.
To reset the display, push the “DISP” button for about 5
seconds or more.
NOTE● While the ignition switch is in the “ON” position, the
automatic reset mode is perm anently selected. If you wish
to make continuous measur ements, select the manual
mode.
Display brightness adjustmentE00509600050
1. Press and hold down button (A), then press the “H” button (B) within 1 second. A buzzer will sound, and the system
will allow adjustment of the display brightness.