2008 MERCEDES-BENZ SL550 wheel

424 Practical hints
Flat tire
Detach the electric air pump.
Stow the electrical plug and the air
hose behind the flap and place the air
pump back in the trunk.
Lowering the vehicle
Lower vehicle by turning crank coun-
terclockwise until the full weight of the
vehicle is resting on the ground.
Pull the jack out of the jack support
tube.1 - 5 Wheel bolts
Tighten the five wheel bolts evenly,
following the diagonal sequence
illustrated (1 to 5), until all bolts
are tight. Observe a tightening torque
of 96 lb-ft (130 Nm).
Warning!G
Follow recommend inflation pressures.
Do not overinflate tires. Overinflating tires
can result in sudden deflation (blowout) be-
cause they are more likely to become punc-
tured or damaged by road debris, potholes,
etc.
Do not underinflate tires. Underinflated tires
wear unevenly, adversely affect handling
and fuel economy, and are more likely to fail
from being overheated.
Do not overload the tires by exceeding the
specified load limit as indicated on the Tire
and Loading Information placard on the
driver’s door B-pillar. Overloading the tires
can overheat them, possibly causing a
blowout. Overloading the tires can also
result in handling or steering problems, or
brake failure.
iThe flat tire may be transported in the trunk
when the retractable hardtop is raised. If avail-
able, use a protective sheet on the spare wheel.
Vehicles with TPMS or Advanced TPMS*:
Do not activate the tire inflation pressure moni-
tor until a full size wheel/tire with functioning
sensor has been placed back into service on the
vehicle.
Warning!G
Have the tightening torque checked after
changing a wheel. The wheels could come
loose if they are not tightened to a torque of
96 lb-ft (130 Nm).


425 Practical hints
Flat tire
Before storing the jack in the trunk,
crank back to storage position and fold
in the arm.Replacing jack support tube cover
Slide tongue of cover under the upper
edge of the tube opening.
Applying even pressure, press cover
until it snaps into place.
Be careful not to damage the locking
tabs or clamp the plastic retaining
strap.
MOExtended system*
The MOExtended system allows you to
continue driving your vehicle even if there
is a total loss of pressure in one or more
tires.
You may only use the MOExtended system
in conjunction with the Run Flat Indicator*
(Canada vehicles) (
page 303), TPMS
(U.S. vehicles) (
page 305), or Advanced
TPMS* (Canada vehicles) (
page 308).
Warning!G
When turning the wheel wrench to tighten
the wheel bolts, make sure you position
hands on the wrench in such a way that you
avoid injury to yourself, such as scraping
your hands against the wheel. Make sure
turning the wheel wrench will not scratch or
damage the wheel rim.
iFor information on storing the spare wheel
back into the trunk, see “Storing the spare wheel
after use” (
page 402).
!The maximum distance in emergency
mode depends on the vehicle’s load. It is
30 miles (50 km) if the vehicle is partially
loaded and 18 miles (30 km) if the vehicle is
fully loaded.
The point at which the maximum driving distance
begins in emergency mode is when the warning
message appears in the multifunction display
indicating that there is a loss of tire inflation
pressure.
Do not exceed the maximum speed of
50 mph (80 km/h).

428 Practical hints
Batteries
!The factory-equipped VRLA battery is
leak-proofed. Only use a battery as replacement
that has the same security features and is of
identical size, voltage, and capacity as the
factory-equipped battery.
The battery, the battery ventilation and the
lateral plug must always be securely installed
when the vehicle is in operation.
Warning!G
Failure to follow these instructions can
result in severe injury or death.
Never lean over batteries while connecting,
you might get injured.
Battery fluid contains sulfuric acid. Do not
allow this fluid to come in contact with eyes,
skin or clothing. In case it does, immediately
flush affected area with water and seek
medical help if necessary.
A battery will also produce hydrogen gas,
which is flammable and explosive. Keep
flames or sparks away from battery, avoid
improper connection of jumper cables,
smoking, etc.
!Never loosen or detach battery terminal
clamps while the engine is running or the
SmartKey is in the starter switch. Otherwise the
alternator and other electronic components
could be severely damaged.
Have the starter battery checked regularly by an
authorized Mercedes-Benz Center.
Refer to Maintenance Booklet for maintenance
intervals or contact an authorized
Mercedes-Benz Center for further information.
Warning!G
Do not place metal objects on the battery as
this could result in a short circuit.
Use leak-proof batteries only to avoid the
risk of acid burns in the event of an acci-
dent.
Warning!G
The brake system requires electrical power
to operate.
A malfunction in the vehicle’s power supply
or electrical system may impair brake sys-
tem operation and switch it into its emer-
gency operation mode. The same applies if
battery is disconnected. To brake, the driver
must then apply significantly greater brake
pedal pressure and depress the pedal much
further to obtain the expected braking ef-
fect. If necessary, apply full pressure to the
brake pedal. Brakes are only applied to the
front wheels.
Stopping distance is increased! Adjust your
driving style accordingly. For more informa-
tion, see “Electro-hydraulic brake system”
(
page 94).

434 Practical hints
Towing the vehicle
Mercedes-Benz recommends that the vehi-
cle be transported with all wheels off the
ground using flatbed or appropriate wheel
lift/dolly equipment.
When circumstances do not permit the
recommended towing methods, the
vehicle may be towed with all wheels on
the ground or front wheels raised only so
far as necessary to have the vehicle moved
to a safe location where the recommended
towing methods can be employed.
!Do not tow-start the vehicle.
!Use flatbed or wheel lift/dolly equipment
with SmartKey in starter switch turned to
position0.
Do not tow with sling-type equipment. Towing
with sling-type equipment over bumpy roads will
damage radiator and supports.
To prevent damage during transport, do not tie
down vehicle by its chassis or suspension parts.
Switch off the tow-away alarm (
page 100) and
the automatic central locking (
page 166).
Warning!G
If circumstances require towing the vehicle
with all wheels on the ground, always tow
with a tow bar if:

the engine will not run

there is a malfunction in the
electro-hydraulic brake system

there is a malfunction in the power sup-
ply or in the vehicle’s electrical system
This is necessary to adequately control the
towed vehicle.
Prior to towing the vehicle with all wheels on
the ground, make certain that the SmartKey
is in starter switch position2.
Warning!G
The brake system requires electrical power
to operate.
A malfunction in the vehicle’s power supply
or electrical system may impair brake sys-
tem operation and switch it into its emer-
gency operation mode. To brake, the driver
must then apply significantly greater brake
pedal pressure and depress the pedal much
further to obtain the expected braking ef-
fect. If necessary, apply full pressure to the
brake pedal. Brakes are only applied to the
front wheels. Stopping distance is
increased! Adapt your driving style
accordingly. For more information, see
“Electro-hydraulic brake system”
(
page 94).
With the engine not running, there is no
power assistance for the brake and steering
systems. In this case, it is important to keep
in mind that a considerably higher degree of
effort is necessary to brake and steer the ve-
hicle. Adapt your driving accordingly.

435 Practical hints
Towing the vehicle
!If the vehicle is towed with the front axle
raised, the gear selector lever must be in
positionN and the engine must be shut off
(SmartKey in starter switch position0 or1).
Active braking action through the ESP
® may
otherwise seriously damage the brake system.
When towing the vehicle with all wheels on the
ground, the gear selector lever must be in
positionN and the SmartKey must be in starter
switch position2.
When towing the vehicle with all wheels on the
ground or the front axle raised, the vehicle
may be towed only for distances up to
30 miles (50 km) and at a speed not to exceed
30 mph (50 km/h).
!Towing of the vehicle should only be done
using the properly installed towing eye bolt.
Never attach a tow cable, tow rope or tow rod to
the vehicle chassis, frame or suspension parts.
iWhen towing the vehicle with all wheels on
the ground, please note the following:
With the automatic central locking activated and
the SmartKey in starter switch position2, or
KEYLESS-GO* start/stop button in position2,
the vehicle doors lock if the left front wheel as
well as the right rear wheel are turning at vehicle
speeds of approximately 9 mph (15 km/h) or
more.
To prevent the vehicle door locks from locking,
deactivate the automatic central locking
(
page 122).
iTo signal turns while being towed with the
hazard warning flasher in use, turn SmartKey in
starter switch to position2 and activate the
combination switch for the left or right turn
signal in the usual manner – only the selected
turn signal will operate.
Upon canceling the turn signal, the hazard warn-
ing flasher will operate again.
iIf the battery is disconnected or discharged

the SmartKey will not turn in the starter
switch

the gear selector lever will remain locked in
positionP.
For more information, see “Batteries”
(
page 427) and “Jump starting” (page 432).

436 Practical hints
Towing the vehicle
Installing towing eye bolt
Front
Example illustration (SL 550 and SL 600
without Sport Package)
1Cover on passenger side of front
bumper
To remove cover:
Press mark on cover 1 in direction of
arrow.
Lift cover1off to reveal the threaded
hole for towing eye bolt.To reinstall cover:
Fit locking tabs of cover under the
lower edge of the opening in the
bumper.
Apply even pressure on the upper part
of the cover until it snaps into place.
Rear
1Cover on passenger side of rear
bumper
To remove cover:
Insert flat, blunt object as a lever into
upper left or right recess of cover 1.
Loosen cover 1 using the lever.
Fold cover 1 down in direction of
arrow to reveal the threaded hole for
the towing eye bolt.
To reinstall cover:
Fit cover 1 and snap into place.
Installing towing eye bolt
Take the towing eye bolt and the wheel
wrench from the vehicle tool kit
(
page 400).
Screw towing eye bolt into threaded
hole to its stop.
Insert wheel wrench into towing eye
and tighten towing eye bolt by turning
it clockwise.
Removing towing eye bolt
Take the wheel wrench from the
vehicle tool kit (
page 400).
Insert wheel wrench into towing eye
and loosen towing eye bolt by turning it
counterclockwise.
Remove towing eye bolt.

449 Technical data
Rims and tires
Rims and tires
!Only use tires which have been tested and
approved by Mercedes-Benz. Tires approved by
Mercedes-Benz are developed to provide best
possible performance in conjunction with the
driving safety systems on your vehicle such as
ABS or ESP
®. Tires specially developed for your
vehicle and tested and approved by
Mercedes-Benz can be identified by finding the
following on the tire’s sidewall:

MO = Mercedes-Benz Original equipment
tires

MO1 = Mercedes-Benz Original equipment
tires (applicable to selected tire sizes only)

MOE = Mercedes-Benz Original Extended
(tires with limited run-flat characteristics)
original equipment tires
Using tires other than those approved by
Mercedes-Benz may result in damage that is not
covered by the Mercedes-Benz Limited
Warranty.
iFor information on driving with MOExtended
tires, see “MOExtended system” (
page 312).
!Using tires other than those approved by
Mercedes-Benz can have detrimental effects,
such as

poor handling characteristics

increased noise

increased fuel consumption
Moreover, tires and rims not approved by
Mercedes-Benz may, under load, exhibit dimen-
sional variations and different tire deformation
characteristics that could cause them to come
into contact with the vehicle body or axle parts.
Damage to the tires or the vehicle may be the
result.
iFurther information on tires and rims is
available at any authorized Mercedes-Benz
Center. A placard with the recommended tire in-
flation pressures is located on the driver’s door
B-pillar. Some vehicles may have supplemental
tire inflation pressure information for driving at
high speeds (
page 301) or for vehicle loads
less than the maximum loaded vehicle condition
(
page 301). If such information is provided, it
can be found on the placard located on the
inside of the fuel filler flap.The tire inflation pressure should be checked
regularly and should only be adjusted on cold
tires. Follow tire manufacturer’s maintenance
recommendation included with vehicle.
iThe following pages also list the approved
wheel rim and tire sizes for equipping your vehi-
cles with winter tires. Winter tires are not avail-
able as standard or optional factory equipment,
but can be purchased from an authorized
Mercedes-Benz Center.
Depending on vehicle model and the standard or
optional factory-equipped wheel rim/tire config-
uration on your vehicle (Performance Package,
Sport Package etc.), equipping your vehicle with
winter tires approved for your vehicle model may
also require the purchase of two or four wheel
rims of the recommended size for use with these
winter tires. See an authorized Mercedes-Benz
Center for more information.

450 Technical data
Rims and tires
Same size tires
ModelSL 550SL 600
Rims (light alloy)8.5 J x 18 H28.5 J x 18 H2
Wheel offset1.38 in (35 mm)1.38 in (35 mm)
Winter tires1,2
1Radial-ply tires2Not available as factory equipment.
255/40 R18 95V M+S.
or
255/40 R18 95V M+S.MOExtended
3
3Must be used in conjunction with Tire Pressure Monitoring System (U.S. vehicles), Run Flat Indicator (Canada vehicles), or Advanced Tire Pressure Monitoring
System* (Canada vehicles) only.
255/40 R18 95V M+S.
or
255/40 R18 95V M+S.MOExtended
3
ModelSL 55 AMGSL 55 AMG (Performance Package*)
SL 65 AMG
Rims (light alloy)8.5 J x 18 H28.5 J x 19 H2
Wheel offset1.18 in (30 mm)1.18 in (30 mm)
Winter tires1,2
1Radial-ply tires2Not available as factory equipment.
255/40 R18 95V M+S.255/35 R19 96V XL (Extra Load) M+S.