2008 MERCEDES-BENZ S550 4MATIC sensor

384 Controls in detail
Power windows
Switch on the ignition (page 344).
Opening: Press the lower part of
switch1 to 4 (
page 383) to the re-
sistance point.
The corresponding window will move
downwards until you release the
switch.
Closing: Press the upper part of
switch1 to 4 (
page 383) to the re-
sistance point.
The corresponding window will move
upwards until you release the switch.
If the window encounters an obstruction
that blocks its path in a circumstance where
you are closing the window by pressing and
holding the switch, by pressing and holding
button ‹ on the SmartKey or SmartKey
with KEYLESS-GO*, by pressing and holding
the sensor surface (vehicles with
KEYLESS-GO*) on an outside door handle,
or by pressing and holding button, on
the climate control panel, the automatic re-
versal function will not operate.
When leaving the vehicle, always remove the
SmartKey or SmartKey with KEYLESS-GO*
from the starter switch, take it with you, and
lock the vehicle. Do not leave children unat-
tended in the vehicle, or with access to an
unlocked vehicle. A child’s unsupervised ac-
cess to a vehicle could result in an accident
and/or serious personal injury.iYou can also open or close the windows us-
ing the SmartKey, see “Summer opening fea-
ture” (
page 385) and “Convenience closing
feature” (
page 386).
Depending on current position, the windows may
also open or close when the air recirculation
button, (
page 469) is pressed and held
for 2 seconds.
iOperating the windows from the rear is not
possible if you activate the override switch
(
page 63).
iIf PRE-SAFE® has been activated, the door
windows close automatically until only a small
gap remains.
iWith the SmartKey in starter switch
position0 or removed from the starter switch,
the power windows can be operated:

until you open the driver’s or front passenger
door

for at least 5 minutes if no door was opened
Warning!G
If you press and hold the switch up when
closing the window, and upward movement
of the window is blocked by some obstruc-
tion including but not limited to arms, hands,
fingers, etc., the automatic reversal will not
operate.


385 Controls in detail
Power windows
Express-opening: Press the lower part
of switch1 to4 (
page 383) past
the resistance point and release.
The corresponding window opens com-
pletely.
Express-closing: Press the upper part
of switch1 to4 (
page 383) past
the resistance point and release.
The corresponding window closes com-
pletely.
Stopping during Express-operation:
Briefly press the respective power win-
dow switch again.
Rear side window sunshades*
Closing: With the side window fully
closed, press the upper part of
switch3 or4 (
page 383).
The rear side window sunshade will be
fully closed.
Opening: Press the lower part of
switch3 or4 (
page 383).
The rear side window sunshade will be
fully opened.
Summer opening feature
If the weather is warm, you can ventilate
the vehicle before driving off by simulta-
neously:

opening the door windows and rear
side window sunshades*

opening the tilt/sliding sunroof or
tilt/sliding panel* and extending the
roller sunblinds*

turning on the seat ventilation* for the
driver’s seat
Warning!G
Driver’s door only:
If within 5 seconds you again press the
switch past the resistance point and re-
lease, the automatic reversal will not oper-
ate.
!If the upward movement of the window is
blocked during the closing procedure, the win-
dow will stop and open slightly. Remove the ob-
struction, press the respective power window
switch at the upper part again past the resis-
tance point and release. If the window still does
not close when there is no obstruction, press
and hold the respective power window switch at
the upper part. The side window will then close
without the obstruction sensor function.
iThe rear side window sunshade cannot be
partially closed.
iThe switches on the rear doors can also be
used to close the rear side window sunshades on
the other side of the vehicle.
iThe switches on the driver’s door take pre-
cedence over the rocker switches on the other
doors.

387 Controls in detail
Power windows
Vehicles with SmartKey
Aim transmitter eye of the SmartKey
towards the sensor in the driver’s door
handle. The SmartKey must be in close
proximity to the driver’s door handle.
Vehicles with tilt/sliding sunroof
Press and hold button ‹ until the
door windows and the tilt/sliding sun-
roof are completely closed.
Release button ‹ to interrupt pro-
cedure.Vehicles with panorama roof* and/or
rear side window sunshades*
Press and hold button ‹ until the
door windows and the tilt/sliding panel
are completely closed.
Press and hold button ‹ again.
The roller sunblinds and/or rear side
window sunshades* close.
Release button ‹ to interrupt pro-
cedure.
Warning!G
When closing the windows and the tilt/slid-
ing sunroof or tilt/sliding panel*, make sure
that there is no danger of anyone being
harmed by the closing procedure.
If potential danger exists, proceed as fol-
lows:

Release button ‹ to stop the closing
procedure. To open, press and hold but-
ton Œ. To continue the closing after
making sure that there is no danger of
anyone being harmed by the closing pro-
cedure, press and hold button‹.
Vehicles with KEYLESS-GO*:

Release the sensor surface on the out-
side door handle (
page 388) to stop
the closing procedure.

Immediately pull on the same outside
door handle and hold firmly. The door
windows and the tilt/sliding sunroof or
tilt/sliding panel* will open for as long
as the outside door handle is held but
the door is not opened.
iIf you press ‹ while one of the front door
windows is open and one of the rear door win-
dows is closed, for example, then the front side
window and the rear side window sunshade will
be closed. To prevent this from happening, first
open all door windows slightly by briefly
pressingΠand then close all door windows
by pressing ‹.

388 Controls in detail
Power windows
Vehicles with KEYLESS-GO*
1Sensor surface on door handle
The SmartKey with KEYLESS-GO must be
located outside the vehicle within approxi-
mately 3 ft (1 m) of a door.
Close all doors.Vehicles with tilt/sliding sunroof
Touch and hold sensor surface1 until
the windows and the tilt/sliding sun-
roof are completely closed.
Release sensor surface1 to interrupt
procedure.Vehicles with panorama roof* and/or
rear side window sunshades*
Touch and hold sensor surface1 until
the windows and the tilt/sliding panel
are completely closed.
Touch and hold sensor surface1
again.
The roller sunblinds and/or rear side
window sunshades* close.
Release sensor surface1 to interrupt
procedure.
iMake sure that you are only touching the
sensor surface.
iMake sure that you are only touching the
sensor surface.
iIf you touch the sensor surface while one of
the front door windows is open and one of the
rear door windows is closed, for example, the
front side window will be closed as well as the
rear side window sunshade*.

418 Controls in detail
Instrument cluster
Tachometer
The red marking on the tachometer de-
notes excessive engine speed.To help protect the engine, the fuel supply
is interrupted if the engine is operated
within the red marking.
Outside temperature indicator
The outside temperature indicator is on
the bottom left-hand side of the instru-
ment cluster (
page 28).
The temperature sensor is located in the
front bumper area. Due to its location, the
sensor can be affected by road or engine
heat during idling or slow driving. There-
fore, the accuracy of the displayed temper-ature can only be verified by comparison to
a thermometer placed next to the sensor,
not by comparison to external displays
(e.g. bank signs, etc.).
When moving the vehicle into colder ambi-
ent temperatures (e.g. when leaving your
garage), you will notice a delay before the
lower temperature is displayed.
A delay also occurs when ambient temper-
atures rise. This prevents inaccurate tem-
perature indications caused by heat
radiated from the engine during idling or
slow driving.
Fuel gauge
The fuel gauge is on the left-hand side of
the instrument cluster (
page 28). Once
the fuel level has fallen below the reserve
mark, the yellow segment indicator for the
fuel reserve comes on (
page 605).
of the vehicle and do not stand near the ve-
hicle until the engine has cooled down.
!Excessive coolant temperature triggers a
warning in the multifunction display
(
page 646).
The engine should not be operated with the cool-
ant temperature above 248°F (120°C), i.e. in
the red zone of the coolant temperature gauge.
Doing so may cause serious engine damage
which is not covered by the Mercedes-Benz Lim-
ited Warranty.
iDuring severe operating conditions,
e.g. stop-and-go traffic, the coolant temperature
may rise close to 248°F (120°C), i.e. close to
the red zone of the temperature gauge.
!Avoid driving at excessive engine speeds, as
it may result in serious engine damage that is not
covered by the Mercedes-Benz Limited
Warranty.
Warning!G
The outside temperature indicator is not de-
signed to serve as an ice-warning device and
is therefore unsuitable for that purpose.
Indicated temperatures just above the freez-
ing point do not guarantee that the road sur-
face is free of ice. The road may still be icy,
especially in wooded areas or on bridges.


424 Controls in detail
Driving systems
Briefly pull the cruise control lever in
the direction of arrow4 (
page 420).
The cruise control resumes to the last
set speed or if no speed is stored, it will
set and store the current speed.
Remove your foot from the accelerator
pedal.
The last set speed appears in the multi-
function display for approximately
5 seconds, and the corresponding
speedometer segments from the se-
lected speed to the vehicle maximum
speed are illuminated.
DISTRONIC Plus*
When activated, the DISTRONIC Plus adap-
tive cruise control system increases driv-
ing convenience afforded by the cruise
control during travel on expressways and
other major roadways.

If the DISTRONIC Plus distance sensor
detects a slower moving vehicle direct-
ly ahead, your vehicle speed will be re-
duced so that you follow that vehicle at
a preset distance.

If there is no vehicle directly ahead of
you, DISTRONIC Plus will function in
the same way as the cruise control
(
page 419).
DISTRONIC Plus functions within a speed
range of 0 to 120 mph.When travelling in Canada in a vehicle not
registered in Canada, you must switch off
the radar sensor system* (
page 282).
Canadian law does not permit the use of
the radar sensor system* (
page 282) for
vehicles from outside of Canada. When you
switch off the radar sensor system*, the
following functions are deactivated:

BAS Plus* (page 69)

DISTRONIC Plus

Park Assist* (page 448)

PRE-SAFE® Brake* (page 76)
iThe last stored set speed is deleted when
the engine is turned off.

426 Controls in detail
Driving systems
DISTRONIC Plus does not act upon adverse
sight distance conditions. Do not use
DISTRONIC Plus during conditions of fog
and heavy rain, snow or sleet.
Warning!G
DISTRONIC Plus cannot take weather condi-
tions into account. Switch off
DISTRONIC Plus or do not turn it on if:

roads are slippery or covered with snow
or ice. The wheels could lose traction
while braking or accelerating, and the
vehicle could skid.

the sensor is dirty or visibility is
diminished due to snow, rain or fog. The
distance control could be impaired.
Always pay attention to traffic conditions
even while DISTRONIC Plus is switched on.
Otherwise, you may not be able to recognize
dangerous situations until it is too late and
could cause an accident resulting in person-
al or fatal injury to you or others.
Warning!G
The “Resume” function should only be oper-
ated if the driver is fully aware of the previ-
ously set speed and wishes to resume this
particular preset speed.
Warning!G
Close attention to road and traffic condi-
tions is imperative at all times, regardless of
whether or not DISTRONIC Plus is activated.
Use of DISTRONIC Plus can be dangerous
on winding roads as conditions do not allow
safe driving at a steady speed.
DISTRONIC Plus may not react to stationary
objects in the roadway (e.g. a stopped vehi-
cle in a traffic jam or a disabled vehicle).
DISTRONIC Plus will also not respond to on-
coming vehicles.
Switch off DISTRONIC Plus:

when changing from the left to the right
lane if vehicles are moving more slowly
in the left lane

when entering a turn lane or highway off
ramp

in complex driving situations, such as in
highway construction zones
In these situations, DISTRONIC Plus will
continue to maintain the set speed unless
deactivated.
DISTRONIC Plus is designed and intended
only to maintain a set speed and keep a set
distance from moving objects in front of it.
iDo not use DISTRONIC Plus if you are driv-
ing on a road with steep uphill or downhill slopes.
iDue to its radar-emitting nature DISTRONIC
Plus may have an appearance similar to a radar
detector to law enforcement officials. You may
want to refer to this section of your Operator’s
Manual when asked.


427 Controls in detail
Driving systems
DISTRONIC Plus displays in multifunc-
tion display
1Speed of the vehicle ahead
2Set speed
3Distance warning lamp
If DISTRONIC Plus is activated, the
marker2 indicates the set speed.
When DISTRONIC Plus detects a vehicle
driving ahead of you, the ring on the speed-
ometer dial lights up between the speed of
the vehicle ahead of you and set speed2.If DISTRONIC Plus calculates that there is
a danger of collision:

The distance warning lampl in the
instrument cluster comes on.

An intermittent warning sounds.
Immediately brake the vehicle to avoid
a collision.
Under no circumstances should the
driver await the intermittent warning
sound before braking. See the follow-
ing warning note.
The intermittent warning sound ceases
and the distance warning lampl
goes out when the necessary distance
to the vehicle ahead is again
established.
iUSA only:
This device has been approved by the FCC as a
“Vehicular Radar System”. The radar sensor is
intended for use in an automotive radar system
only. Removal, tampering, or altering of the de-
vice will void any warranties, and is not permitted
by the FCC. Do not tamper with, alter, or use in
any non-approved way.
Any unauthorized modification to this device
could void the user’s authority to operate the
equipment.
iCanada only:
This device complies with RSS-210 of Industry
Canada. Operation is subject to the following
two conditions:
(1) This device may not cause interference, and
(2) this device must accept any interference re-
ceived, including interference that may
cause undesired operation of the device.
Removal, tampering, or altering of the device will
void any warranties, and is not permitted. Do not
tamper with, alter, or use in any non-approved
way.
Any unauthorized modification to this device
could void the user’s authority to operate the
equipment.
iThe vehicle speed displayed on the speed-
ometer can briefly vary from the speed setting
on the DISTRONIC Plus system.
Warning!G
An intermittent warning sounds and the dis-
tance warning lampl in the instrument
cluster is illuminated if the DISTRONIC Plus
system calculates that the distance to the