2008 MERCEDES-BENZ S-Class seats

378 Controls in detailSeatsExample illustration driver’s door1Seat heating button
Switch on the ignition (
page 370).

Switching on: Press button1 repeat-
edly until the desired heating level is
set.
One or more red indicator lamps on the
button show the selected heating level.

Switching off: Press button1 repeat-
edly until all indicator lamps go out.
Seat ventilation*
The buttons for seat ventilation are located
on the respective door. The blue indicator
lamps on the button come on to show the
ventilation level selected.
Example illustration driver’s door1Seat ventilation button
Switch on the ignition (
page 370).

Switching on: Press button1 repeat-
edly until the desired ventilation level is
set.
One or more blue indicator lamps on
the button show the selected ventila-
tion level.
i
If one or more of the lamps on the seat heat-
ing button are flashing, there is insufficient volt-
age available since too many electrical
consumers are turned on. The seat heating
switches off automatically.
The seat heating will switch back on again auto-
matically as soon as sufficient voltage is avail-
able.
Level3
Three indicator lamps on
(highest level)
2
Two indicator lamps on
1
One indicator lamp on
(lowest level)
off
No indicator lamp on
i
The seat ventilation for the driver’s seat can
be activated using summer opening feature
(
page 412).

379 Controls in detailSeats

Switching off: Press button1 repeat-
edly until all indicator lamps go out.
Head restraints Front seat active head restraints
You cannot remove the active head re-
straint on the driver’s and front passen-
ger’s seats.
For removal contact an authorized
Mercedes-Benz Center.
For information on active head restraints,
see “Active head restraints” (
page 56).
Head restraint height
1Head restraint height

Press the switch up or down in the di-
rection of arrow1.
i
If one or more of the lamps on the seat ven-
tilation button are flashing, there is insufficient
voltage available since too many electrical con-
sumers are turned on. The seat ventilation
switches off automatically.
The seat ventilation will switch back on again au-
tomatically as soon as sufficient voltage is avail-
able.
Warning!
G
For your protection, drive only with properly
positioned head restraints.
Adjust the head restraint so that it is as
close to the head as possible and the center
of the head restraint supports the back of
the head at eye level. This will reduce the po-
tential for injury to the head and neck in the
event of an accident or similar situation.
Do not drive the vehicle without the seat
head restraints. Head restraints are intend-
ed to help reduce injuries during an acci-
dent.i
Adjust the head restraint in such a way that
it is as close to the head as possible.


380 Controls in detailSeatsHead restraint adjusting
1Adjusting head restraint
Push or pull on the upper edge of the
head restraint cushion to the desired
position.Luxury head restraint* adjusting
1Head restraint side cushions
2Adjusting head restraint forward and
backward
You can individually adjust side
cushions1 of the luxury head restraints.

Adjusting side cushions: Pul l or pu sh
side cushions1 into desired position.

Adjusting forward or backward: Pull
or push head restraint in direction of
arrow2.
Rear head restraints
i
Depending on the seat’s set fore and aft po-
sition, the head restraint height is automatically
pre-set.
Warning!
G
When folding back the side cushions, never
reach between the side cushion and the
mounting post. You could otherwise be
trapped.
Warning!
G
For safety reasons, always drive with the
rear head restraints in the upright position
when the rear seats are occupied.
Otherwise, the back of the head will not be
supported in the event of a collision. As a re-
sult, rear seat occupants could be injured.Warning!
G
Keep the area around head restraints clear
of articles (e.g. clothing) to not obstruct the
folding operation of the head restraints.


381 Controls in detailSeats
Folding head restraints back
The rear seat head restraints and the rear
seat power head restraints* can be folded
backward for increased visibility.
1Switch in the front center console
Switch on the ignition (
page 370).

Press switch1 in the front center con-
sole briefly.
The rear head restraints will fold back-
ward.Placing head restraints upright

Pull the rear head restraint upright until
it locks into position.Placing power head restraints* upright
(rear outer seats)

Switch on the ignition (
page 370).

Press and hold switch1 in the front
center console (
page 381).
The rear outer seats head restraints
will place upright.

Pull the rear center seat head restraint
upright manually until it locks into posi-
tion.
!
M ake s ure t he h ead re str ain ts e ng ag e w he n
placing them upright manually. Otherwise their
protective function cannot be ensured.
i
When you fasten your seat belt in the rear,
the respective rear outer seat head restraint
places upright automatically.

382 Controls in detailSeatsRear power head restraints*
(rear outer seats)
1Placing upright head restraint
2Head restraint tilt
3Folding down head restraint
4Head restraint tilt
Press switch up in the direction of
arrow1.
The rear outer seats power head re-
straint will place upright.

Press switch down in the direction of
arrow3.
The rear power head restraint will fold
down.

Press the switch forward or backward
in the direction of arrow2 or4.
The power head restraint will be tilted.
Luxury head restraints*
(rear outer seats)1Head restraint side cushions
2Head restraint height
You can individually adjust side
cushions1 of the luxury head restraints:

Adjusting side cushions: Pul l or pu sh
side cushions1 into desired position.

Adjusting head restraint angle: Push
or pull on the lower edge of the head re-
straint cushion in the direction of
arrow2.
i
Depending on vehicle production date you
have to switch on the ignition or open the re-
spective door before adjusting the rear power
head restraints.
Warning!
G
When folding back the side cushions, never
reach between the side cushion and the
mounting post. You could otherwise be
trapped.
i
Depending on vehicle production date you
have to switch on the ignition or open the re-
spective door before adjusting the rear luxury
head restraints.

383 Controls in detailSeats
Multicontour seats*, rear
You can adjust the rear outer multicontour
seats using the buttons on the center con-
sole.
1To select right rear passenger seat
2Massage setting, gentle
3Massage setting, vigorous
4To adjust position of backrest curva-
ture (lordosis)
5Lumbar region support
6Side bolster adjustment
7To select left rear passenger seat

Switch on the ignition.

Selecting a seat: Press rocker
switch1 or7 forward or backward.
The indicator lamp on the selected but-
ton lights up for a short while.
Gentle massage

Switching on: Press rocker switch2
forward.

Switching off: Pull rocker switch2
backward.
Vigorous massage

Switching on: Press rocker switch3
forward.

Switching off: Pull rocker switch3
backward.Position of backrest curvature

Moving upward: Press rocker
switch4 forward.

Moving downward: Pull rocker
switch4 backward.
Lumbar region support

Selecting greater curvature: Press
rocker switch5 forward.

Selecting less curvature: Pull rocker
switch5 backward.
Side bolster adjustment

Reducing width: Press rocker
switch6 forward.

Increasing width: Pull rocker
switch6 backward.

384 Controls in detailSeatsEasy-entry/exit feature
This feature allows for easier entry into and
exit from the vehicle. When entering and
exiting the vehicle, the driver’s seat is in its
maximum rearward position and the steer-
ing wheel is in its uppermost position.
The easy-entry/exit feature can be activat-
ed or deactivated in the “Vehicle” menu of
the COMAND system (
page 268).With the easy-entry/exit feature activated,
the steering wheel and driver’s seat will re-
turn to their last set memory position or a
factory-set maximum forward position
when you:


close the driver’s door with the ignition
switched on


insert the SmartKey into the starter
switch or press the KEYLESS-GO*
start/stop button (
page 372) once
with the driver’s door closed
Warning!
G
You must make sure no one can become
trapped or injured by the moving steering
wheel and driver’s seat when the easy-en-
try/exit feature is activated.
To stop seat/steering wheel movement, do
one of the following:

Press seat adjustment switch
(page 374).


Move steering wheel adjustment stalk
(page 386).


Press one of the memory position but-
tons or the memory buttonM
(page 393).
Do not leave children unattended in the ve-
hicle, or with access to an unlocked vehicle.
Children could open the driver’s door and
unintentionally activate the easy-entry/exit
feature, which could result in an accident
and/or serious personal injury.
!
Do not activate the easy-entry/exit feature
if the seat backrest is in an excessively reclined
position. Doing so could cause damage to front
or rear seats.
First move the seat backrest to an upright posi-
tion.
i
For safety reasons, the driver’s seat will not
return to its last set position with the easy-en-
try/exit feature activated if the system recogniz-
es the last set position as an extreme forward
position. Instead, the driver’s seat will remain at
or move to a factory-set maximum forward posi-
tion. To again fully return the driver’s seat to

385 Controls in detailSeats
With the easy-entry/exit feature activated
the steering wheel tilts upwards and the
driver’s seat moves a few inches to the
rear when you:

remove the SmartKey from the starter
switch,
or


open the driver’s door with the
SmartKey in starter switch position0
or1 or the KEYLESS-GO* start/stop
button (
page 372) in position1
your last set position or to memory position, ad-
just the seat to the desired position or press and
hold the respective memory position button
(page 393).
i
The last set driver’s seat and steering wheel
positions are stored when


the ignition is switched off (
page 370)


the position is stored in memory
(page 392)
i
If the current position for the steering wheel
is in the uppermost tilt position, the steering
wheel will no longer be able to move upward
when the easy-entry/exit feature is activated.
If the current seat position falls into a factory-set
position range and the system recognizes the
current seat position to be rearward enough for
easy entry and exit, the driver’s seat will not
move to the rear when the easy-entry/ exit fea-
ture is activated.
The adjustment procedure is briefly interrupted
when the engine is started.Warning!
G
Let the system complete the adjustment
procedure before setting the vehicle in mo-
tion. All driver’s seat and steering wheel ad-
justments must be completed before setting
the vehicle in motion. Driving off with the
driver’s seat/steering wheel still adjusting
could cause the driver to lose control of the
vehicle.