2008 MERCEDES-BENZ ML SUV clock

Changing the bulbs
317Front foglamp
3
Foglamp screws
X Remove screws 3.
i Only remove screws 3. Do not turn the
front foglamp adjustment screws. If the
adjustment screws are turned, the front
foglamp adjustment must be checked at a
qualified specialist workshop, e.g. a
Mercedes-Benz Service Centre.
X Remove front foglamp 2. Front foglamp
4 Bulb holder for front foglamp
X Turn bulb holder 4anti-clockwise to the
stop and remove it.
X Pull the bulb out of bulb holder 4.
X Insert the new bulb into bulb holder 4.
X Insert bulb holder 4and turn it clockwise.
X Insert front foglamp 2.
X Replace and tighten screws 3.
X Insert cover 1and press in firmly.
Cover 1snaps into place. Replacing the bulbs in foglamps with
cornering light function* 1
Front foglamp
2 Cover screws
3 Cover
X Switch off the lights.
X Remove screws 2.
X Remove cover 3with foglamp with cor-
nering light function. Practical advice
* optional
164_AKB; 5; 5, en-GB
wobuchh,
Version: 2.10.6 2008-05-11T11:55:12+02:00 - Seite 317 ZDateiname: 6515_4293_02_buchblock.pdf; preflight

Changing the bulbs
3184
Bulb holder for front foglamp
X Turn bulb holder 4anti-clockwise to the
stop and remove it.
X Pull the bulb out of bulb holder 4.
X Insert the new bulb into bulb holder 4.
X Insert bulb holder 4and turn it clockwise.
X Insert cover 3with foglamp with cornering
light function.
X Replace and tighten the screws 2.Replacing the turn signal lamps 1
Bulb holder for turn signal (PY 5 W)
2 Bulb holder for turn signal (P 21 W)
X Switch off the lights.
X Open the bonnet.
X Turn bulb holder 1or2 anti-clockwise
and pull it out.
X Pull the bulb out of bulb holder 1or2.
X Insert the new bulb into bulb holder 1or
2.
X Insert bulb holder 1or2 and turn clock-
wise. Changing the rear bulbs
Opening and closing the side trim pan-
els You must open the side trim panel in the load
compartment before changing the bulbs in
the tail lamps.
Left-hand side trim panel
Left-hand side trim panel
1
Release catch
2 Side trim panel
X To open the side trim panel: turn catch
1 90° in the direction of the arrow and
remove side trim panel 2.Practical advice
164_AKB; 5; 5, en-GB
wobuchh,
Version: 2.10.6 2008-05-11T11:55:12+02:00 - Seite 318Dateiname: 6515_4293_02_buchblock.pdf; preflight

Changing the bulbs
320Tail lamps with LEDs*
1
Reversing lamp
2 Rear fog lamp
3 Rear fog lamp
X Turn the corresponding bulb holder anti-
clockwise and remove it.
X Take the bulb out of the bulb holder.
X Insert the new bulb into the bulb holder.
X Insert the bulb holder and turn it clockwise.
X Close the side trim panel (Y page 318).Vehicles with an exterior spare wheel
bracket*
On vehicles with an exterior spare wheel
bracket*, the following lamps are located in
the bumper:
R
Tail lamp
R Parking lamp
R Brake lamp
R Turn signal lamp
R Licence plate lamp Bumper
1
Lamp cluster
X Switch off the lights.
X Insert a plastic card into the gap between
the bumper and lamp cluster 1.X
Push the plastic card in the direction of the
arrow.
Lamp cluster 1pops out.
X Remove lamp cluster 1. Lamp cluster
1
Bulb holder for turn signal lamp
2 Bulb holder for tail lamp/parking lamp/
brake lamp
X Turn the corresponding bulb holder anti-
clockwise and remove it.
X Lightly press the bulb into the bulb holder,
turn it anti-clockwise and remove it from
the bulb holder.
X Insert the new bulb into the bulb holder and
turn it clockwise. Practical advice
* optional
164_AKB; 5; 5, en-GB
wobuchh,
Version: 2.10.6 2008-05-11T11:55:12+02:00 - Seite 320Dateiname: 6515_4293_02_buchblock.pdf; preflight

Replacing the wiper blades
321
X
Insert the corresponding bulb holder and
turn it clockwise.
X Insert lamp unit 1and press in firmly.
Lamp unit 1snaps into place.
Changing the bulbs in the licence plate
lamps Licence plate lamp
1
Screws
X Switch off the lights.
X Open the tailgate.
X Remove screws 1.
X Remove the licence plate lamp.
X Replace the bulb.
X Insert the licence plate lamp.
X Replace and tighten screws 1. Replacing the wiper blades
Windscreen wiper blades
G
Risk of accident
The windscreen will not longer be properly
wiped if the wiper blades are worn. This
could prevent you from observing the traffic
conditions, thereby causing an accident.
Replace the wiper blades twice a year, ide-
ally in spring and autumn. G
Risk of accident
The wiper arms could start moving and
cause an injury if you leave the windscreen
wipers switched on.
Remove the key from the ignition lock
before replacing the wiper blades.
! Make sure that you touch only the wiper
arm of the windscreen wiper to avoid dam-
aging the windscreen wiper blades. Removing 1
Wiper blade
2 Release clips
3 Folding direction
4 Wiper arm
5 To remove the wiper blade
X Remove the key from the ignition lock.
X Fold wiper arm 4away from the wind-
screen until it engages.
X Press both release clips 2.
X Fold wiper blade 1in the direction of
arrow 3.
X Remove the wiper blade in the direction of
arrow 5. Practical advice
164_AKB; 5; 5, en-GB
wobuchh,
Version: 2.10.6 2008-05-11T11:55:12+02:00 - Seite 321 ZDateiname: 6515_4293_02_buchblock.pdf; preflight

Battery
338while it is still installed. Otherwise, the vehi-
cle's electronic system may be damaged.
! Only use battery chargers with a maxi-
mum charging voltage of 14.8 V.
X Charge the battery. Observe the notes in
the operating instructions for your battery
charger.
X Refit the charged battery.
To do this, follow the steps described in
"Removing the battery" (Y page 337) in
reverse order.
i You can charge the battery using the
jump-start terminals. These are located on
the right when viewed in the direction of
travel.
X Open the bonnet (Y page 219). Jump-start terminals
1
Body earth point (negative terminal)
2 Positive terminal (under cover) Reconnecting the battery
! Always reconnect the battery in the
sequence described below. Never swap the
terminal clamps. You may otherwise dam-
age the vehicle electronics.
X Switch off all electrical consumers.
X Connect the positive terminal clamp and
secure the cover.
X Connect the negative terminal clamp.
X Connect the breather hose. Make sure that
a cell cap is fitted is fitted on the side. i
If the battery power supply has been inter-
rupted (e.g. if it has been reconnected), you
must carry out the following tasks:
R Set the time (Y page 130).
On vehicles with COMAND and a naviga-
tion system*, the clock is set automati-
cally
R Reset the sliding/tilting sun-
roof* (Y page 189).
R Reset the function for folding the exterior
mirrors in/out automatically* by folding
the mirrors out once ( Ypage 86).
R Reset the side windows (Y page 101)Practical advice
* optional
164_AKB; 5; 5, en-GB
wobuchh
,V ersion: 2.10.6
2008-05-11T11:55:12+02:00 - Seite 338 Dateiname: 6515_4293_02_buchblock.pdf; preflight

Towing and tow-starting
342
Vehicles with the off-road styling pack-
age* 1
Cover
X Use a suitable object such as a screwdriver
to prise off and remove cover 1at the
recess.
Securing the towing eye X
Take the towing eye and the wheel wrench
from the vehicle tool kit ( Ypage 255).
X Screw in the towing eye clockwise to the
stop.
X Insert the wheel wrench handle into the
towing eye and tighten it. Towing the vehicle
! You may tow the vehicle for a maximum
of 50 km. A towing speed of 50 km/h must
not be exceeded.
With towing distances over 50 km, the
entire vehicle needs to be lifted up and
transported.
! You should not have the vehicle towed
with the front or rear axle raised.
X Turn the key to position 2(Y page 75) in
the ignition lock.
i On vehicles with KEYLESS GO*: use the
key instead of the KEYLESS GO * button.
X Move the DIRECT SELECT lever to the N
position. Removing the towing eye
X Take the wheel wrench from the vehicle
tool kit ( Ypage 255).
X Insert the wheel wrench handle into the
towing eye and turn it anti-clockwise.
X Unscrew the towing eye.
X Replace the cover and press it until it
engages.
X Return the towing eye and the wheel
wrench to the vehicle tool kit. Transporting the vehicle
The towing eyes or trailer coupling *can be
used to pull the vehicle onto a trailer or trans-
porter if you wish to transport it.
! Only lash the vehicle down by the wheels
or wheel rims, not by parts of the vehicle
such as axle or steering components. The
vehicle could otherwise be damaged. Practical advice
* optional
164_AKB; 5; 5, en-GB
wobuchh,
Version: 2.10.6 2008-05-11T11:55:12+02:00 - Seite 342Dateiname: 6515_4293_02_buchblock.pdf; preflight