2008 MERCEDES-BENZ G55AMG steering wheel

114 Controls in detail
Memory function
Prior to operating the vehicle, the driver
should check and adjust the seat height,
seat position fore and aft, and seat back-
rest angle if necessary, to ensure adequate
control, reach and comfort. The head
restraint should also be adjusted for
proper height. See also the section on
air bags (
page 70) for proper seat
positioning.
In addition, adjust the steering wheel to
ensure adequate control, reach, operation
and comfort. Both the interior and exterior
rear view mirrors should be adjusted for
adequate rear vision.
Fasten seat belts. Infants and small
children should be se ated in a properly
secured restraint system that complies
with U.S. Federal Motor Vehicle Safety
Standards 213 and 225 and Canadian
Motor Vehicle Safety Standards 213 and
210.2. With the memory function you can store up
to three different configurations.
Each stored position on the driver’s side
includes the following settings:

Seat position

Multicontour seat*: previously saved
setting

Steering wheel position

Exterior rear view mirrors’ position
Each stored position on the passenger side
includes the following settings:

Seat position

Multicontour seat*: previously saved
setting
Warning!G
Do not activate the memory function while
driving. Activating the memory function
while driving could cause the driver to lose
control of the vehicle.
W463.boo Seite 114 Montag, 19
. November 2007 8:41 08

115
Controls in detail
Memory function
The memory button and memory position
button are located on each front door.
1
Memory button
1, 2, 3 Memory position button
Switch on the ignition (page 39).
or
Open the respective door.
Storing positions into memory
Adjust the seats (page 42).
On the driver’s side, additionally adjust
the steering wheel (
page 44) and
exterior rear view mirrors (
page 46)
to the desired positions.
Press memory button 1.
Release memory button 1 and press
memory position button 1, 2 , or 3 with-
in 3 seconds.
All settings are stored to the selected
position.
Recalling positions from memory
Press and hold memory position
button 1, 2 , or 3 until the seat, steering
wheel and exterior rear view mirrors
have fully moved to the stored posi-
tions.
!Do not operate the power seats using
memory button 1 if the seat backrest is in an
excessively reclined position. Doing so could
cause damage to front or rear seats.
Move seat backrest to an upright position first.
iReleasing the memory position button stops
movement to the stored positions immediately.
W463.boo Seite 115 Montag, 19 . November 2007 8:41 08

116 Controls in detail
Memory function
Storing exterior rear view mirror
parking position (Canada only)
For easier parking, you can adjust the
passenger-side exterior rear view mirror so
that you can see the rear wheel and the
road curb as soon as you engage reverse
gearR.
For information on activating the parking
position, see “Activating exterior rear view
mirror parking position (Canada only)”
(
page 178).
The memory button is located on the
driver’s door. The adjustment button and
exterior rear view mirror buttons are
located on the dashboard to the left of the
steering wheel. 1
Adjustment button
2 Driver’s side exterior rear view mirror
button
3 Passenger-side exterior rear view
mirror button
4 Memory button
Switch on the ignition (page 39).
Press button 3.
The passenger-side exterior rear view
mirror is selected.
Adjust the exterior rear view mirror
with adjustment button 1 so that you
see the rear wheel and the road curb.
Press memory button 4.
Within 3 seconds, press bottom of
adjustment button 1.
The parking position is stored if the
mirror does not move.
iIf the mirror does move, repeat the above
steps. After the setting is stored, you can move
the mirror again.
W463.boo Seite 116 Montag, 19 . November 2007 8:41 08

117
Controls in detail
Lighting
 Lighting
For information on how to switch on the
headlamps and use the turn signals, see
“Switching on headlamps” (
page 56)
and see “Turn signals” (
page 57).
Exterior lamp switch
The exterior lamp switch is located on the
dashboard to the left of the steering wheel.
iIf you drive in countries where vehicles drive
on the other side of the road than the country in
which the vehicle is registered, you must have
the headlamps modified for symmetrical low
beams. Relevant information can be obtained at
any authorized Mercedes-Benz Light Truck
Center.
1‚Standing lamps, left
(turn left two stops)
2ˆStanding lamps, right
(turn left one stop)
3MOff
Daytime running lamp mode
(
page 119)
4UAutomatic headlamp mode
Daytime running lamp mode
(
page 119)
5CParking lamps (also tail lamps,
license plate lamps, side mark-
er lamps, instrument panel
lamps)
6BLow beam headlamps or high
beam headlamps
7‡Front fog lamps
8†Rear fog lamp
iIf you hear a warning signal you have forgot-
ten to switch off the low beam headlamps or the
parking lamps before opening the driver’s door.
In addition the message
Switch off lights
appears in the multifunction display.
Switch off the low beam headlamps or the park-
ing lamps.
If the message
Turn off lights or remove
key
appears in the multifunction display remove
the SmartKey from the starter switch or switch
off the automatic headlamp mode.
!Failure to switch off the exterior lamps when
leaving the vehicle may result in a discharged
battery.
W463.boo Seite 117 Montag, 19 . November 2007 8:41 08

123
Controls in detail
Lighting
Driving forward
Switching on corner
-illuminating front
fog lamps
Depending on whether you are turning
left or right, switch on the left or right
turn signal (
page 57).
The respective front fog lamp comes on
and illuminates the area in the
direction into which you are turning.
or
Turn steering wheel in desired
direction.
The front fog lamp on the side of your
steering direction comes on. Switching off corner-illuminating front
fog lamps
The combination switch for the turn signal
resets automatically after major steering
wheel movements. This
will switch off the
corner-illuminating front fog lamps if they
were activated by switching on the left or
right turn signal.
If the turn signal should stay on after
making the turn, the turn signal and the
corner-illuminating fr ont fog lamps can be
switched off by returning the combination
switch to its original position.
iIf you have switched on the turn signal for
one side but turn the steering wheel in the
opposite direction, the corner-illuminating front
fog lamp comes on for the side indicated by the
turn signal.
The corner-illuminating front fog lamp remains lit
for a maximum of three minutes. Afterwards, it
goes out even if the turn signal is still switched
on.
iThe corner-illuminating front fog lamps
temporarily come on on both sides of the vehicle
if you turn the steering wheel in one direction
and then again in the other direction shortly
thereafter.
iThe corner-illuminating front fog lamps will
come on automatically depending on the steer-
ing angle, even if you did not switch on either
turn signal. If the corner-illuminating front fog
lamps came on automatically, they will also go
out automatically depending on the steering
angle.iThere may be a brief delay before the
corner-illuminating front fog lamps switch off.
W463.boo Seite 123 Montag, 19 . November 2007 8:41 08

131
Controls in detail
Instrument cluster
Coolant temperature gauge
The coolant temperat
ure gauge is on the
left side in the instrument cluster
(
page 26).
Resetting trip odometer
Make sure you are viewing the
standard display (
page 140).
If it is not displayed, press button è
or ÿ on the multifunction steering
wheel (
page 134) repeatedly until
the standard displa y appears in the
multifunction display.
Press and hold reset button 1
(
page 130) until the trip odometer is
reset.
Warning!G

Driving when your engine is overheated
can cause some fluids which may have
leaked into the engine compartment to
catch fire. You could be seriously
burned.

Steam from an overheated engine can
cause serious burns which can occur
just by opening the hood. Stay away
from the engine if you see or hear steam
coming from it.
Stop the vehicle in a safe location away from
other traffic. Turn off the engine, get out of
the vehicle and do not stand near the vehicle
until the engine has cooled down.
!Excessive coolant temperature triggers a
warning message in the multifunction display
(
page 346).
The engine should not be operated with the
coolant temperature above 248°F (120°C).
Doing so may cause serious engine damage
which is not covered by the Mercedes-Benz
Limited Warranty.
iDuring severe operating conditions, e.g.
stop-and-go traffic, the coolant temperature may
rise close to 248°F (120°C).
W463.boo Seite 131 Montag, 19 . November 2007 8:41 08

133
Controls in detail
Control system
 Control system
The control system is activated as soon as
the SmartKey in the starter switch is
turned to position 1. The control system
enables you to

call up information about your vehicle

change vehicle settings
For example, you can use the control
system to find out when your vehicle is
next due for maintenance service, to set
the language for messages in the instru-
ment cluster display, and much more.
The control system relays information to
the multifunction display.
Multifunction display
1 Trip odometer
2 Main odometer
3 Transfer case indicator
4 Current gear selector lever
position/gear range
5 Status indicator (clock)
6 Status indicator (outside temperature
or digital speedometer)
For more information on menus displayed
in the multifunction display, see “Menus”
(
page 136).
Warning!G
A driver’s attention to the road and traffic
conditions must always be his/her primary
focus when driving.
For your safety and the safety of others,
selecting features thro ugh the multifunction
steering wheel should only be done by the
driver when traffic and road conditions per-
mit it to be done safely.
Bear in mind that at a speed of just 30 mph
(approximately 50 km/h), your vehicle is
covering a distance of 44 feet
(approximately 14 m) every second.
W463.boo Seite 133 Montag, 19 . November 2007 8:41 08

134 Controls in detail
Control system
Multifunction steering wheel
The displays in the multifunction display
and the settings in the control system are
controlled by the buttons on the multi-
function steering wheel.1Multifunction display
Operating the control system
2Selecting a submenu or setting the
volume:
Press button
æup / to increase
çdown / to decrease
3Telephone*:
Press button
sto take a call
to dial
to redial
tto end a call
to reject an incoming call
4Menu systems:
Press button
èfor next menu
ÿfor previous menu
5Moving within a menu:
Press button
jfor next display
kfor previous display
iCanada vehicles:
The steering wheel in this vehicle may vary from
steering wheel shown. However, multifunction
steering wheel symbols and feature description
apply to Canada vehicles as well.
iG55AMG:
The steering wheel in this vehicle may vary from
steering wheel shown. However, multifunction
steering wheel symbols and feature description
apply to AMG vehicles as well.
W463.boo Seite 134 Montag, 19 . November 2007 8:41 08