2008 MERCEDES-BENZ G55AMG steering wheel

62 Getting started
Parking and locking
You have now completed your first drive.
You have properly stopped and parked
your vehicle. End your drive as follows.Parking brake
Warning!G
With the engine not running, there is no
power assistance for the brake and the
steering system. In this case, it is important
to keep in mind that a considerably higher
degree of effort is necessary to brake and
steer the vehicle.
Warning!G
Do not park this vehicle in areas where
combustible materials such as grass, hay or
leaves can come into contact with the hot
exhaust system, as thes e materials could be
ignited and cause a vehicle fire.
To reduce the risk of personal injury or
damage to the vehicle drivetrain as a result
of vehicle movement, before turning off the
engine and leaving the vehicle always:

Keep right foot on brake pedal.

Pull the parking brake lever up as many
notches as possible.

Move the gear selector lever to park
position P.

Slowly release brake pedal.

When parked on an incline, turn front
wheels towards the road curb.

Turn the SmartKey in the starter switch
position 0 and remove.

Take the SmartKey with you and lock
vehicle when leaving.
Warning!G
Engaging the parking brake while the vehicle
is in motion can cause the rear wheels to
lock up. You could lose control of the vehicle
and cause an accident. In addition, the
vehicle’s brake lights do not light up when
the parking brake is engaged.
W463.boo Seite 62 Montag, 19. November 2007 8:41 08

64 Getting started
Parking and locking
Switching off headlamps
Turn the exterior lamp switch toM
(
page 56).
For more information, see “Lighting”
(
page 117).
Turning off engine
Move the gear selector lever to park
position P. Apply the parking brake (
page 62).
Turn SmartKey in the starter switch to
position
0.
Remove the SmartKey from the starter
switch.
The immobilizer is activated.
Releasing seat belts
Press seat belt release button
(
page 50).
Allow the retractor to completely
rewind the seat belt by guiding latch
plate.
Warning!G
Do not turn off the engine before the vehicle
has come to a complete stop. With the
engine not running, there is no power assis-
tance for the brake and steering systems. In
this case, it is important to keep in mind that
a considerably higher degree of effort is
necessary to brake and steer the vehicle.
iAlways set the parking brake in addition to
shifting to park position P (
page 164).
On slopes, turn the front wheels towards the
road curb.
iThe SmartKey can only be removed from the
starter switch with the gear selector lever in park
position P and the SmartKey in starter switch
position 0.
!M a k e s u r e t h e s e a t b e l t r e t r a c t s f u l l y s o t h a t
the seat belt and/or latch plate cannot get
caught or pinched in the door or in the seat
mechanism. This can damage the seat belt and
impair the effectiveness of the seat belt, and/or
cause damage to the door and/or door trim
panel. Such damage is not covered by the
Mercedes-Benz Limited Warranty.
Damaged seat belts must be replaced. Contact
an authorized Mercedes-Benz Light Truck
Center.
W463.boo Seite 64 Montag, 19. November 2007 8:41 08

70 Safety and Security
Occupant safety
Air bags
Warning!G
Air bags are designed to reduce the poten-
tial of injury and fatality in certain frontal
impacts (front air bags), or side impacts
(window curtain air bags). However, no
system available today can completely elim-
inate injuries and fatalities.
The deployment of the air bags temporarily
releases a small amount of dust from the air
bags. This dust, however, is neither injurious
to your health, nor does it indicate a fire in
the vehicle. The dust might cause some tem-
porary breathing difficulty for people with
asthma or other breathing trouble. To avoid
this, you may wish to get out of the vehicle
as soon as it is safe to do so. If you have any
breathing difficulty but cannot get out of the
vehicle after the air bag inflates, then get
fresh air by opening a window or door.
Warning!G
The service life of the passenger front air
bag extends to the date indicated on the
label located on the driver side B pillar. To
provide continued reliab ility after that date,
they should be inspected at an authorized
Mercedes-Benz Light Truck Center at that
time and replaced when necessary.
Warning!G
To reduce the risk of injury when the front
air bags inflate, it is very important for the
driver and front passen ger to always be in a
properly seated position and to wear their
respective seat belts.
For maximum protection in the event of a
collision always be in no rmal seated position
with your back against the seat backrest.
Fasten your seat belt and make sure it is
properly positioned on your body
(
page 50).
Since the air bag inflates with considerable
speed and force, a proper seating and hands
on steering wheel position will help to keep
you at a safe distance from the air bag.
Occupants who are unbelted, out of position
or too close to the air bag can be seriously
injured or killed by an air bag as it inflates
with great force in the blink of an eye:

Sit properly belted in a position that is
as upright as possible with your back
against the seat backrest.
W463.boo Seite 70 Montag, 19. November 2007 8:41 08

71
Safety and Security
Occupant safety

Adjust the driver’s seat as far as possi-
ble rearward, still permitting proper
operation of vehicle controls. The
distance from the center of the driver’s
breastbone to the center of the air bag
cover on the steering
wheel must be at
least 10 inches (25 cm) or more. You
should be able to accomplish this by a
combination of adjustments to the seat
and steering wheel. If you have any
problems, please see an authorized
Mercedes-Benz Light Truck Center.

Do not lean with your head or chest
close to the steering wheel or dash-
board.

Keep hands on the outside of steering
wheel rim. Placing hands and arms
inside the rim can increase the risk and
potential severity of hand/arm injury
when driver’s front air bag inflates.

Adjust the front passenger seat as far as
possible rearward from the dashboard
when the seat is occupied.

Always sit as upright as possible, prop-
erly use the seat belts and appropriate
size infant or child restraint system.

Children 12 years old and under must
never ride in the front seat, except in a
Mercedes-Benz authorized
BabySmart
TM compatible child seat,
which operates with the BabySmartTM
system installed in the vehicle to deacti-
vate the passenger front air bag when it
is properly installed. Otherwise they will
be struck by the air bag when it inflates
in a crash. If this happens, serious or
fatal injury will result.
Failure to follow thes e instructions can
result in severe injuries to you or other
occupants.
If you sell your vehicle, it is important that
you make the buyer aware of this safety
information. Be sure to give the buyer this
Operator’s Manual.
Warning!G
Accident research shows that the safest
place for children in an automobile is in the
rear seat. Should yo u choose to place a
child 12 years old or under in the front pas-
senger seat of your vehicle, you must prop-
erly use a BabySmart
TM child restraint which
will turn off the passenger front air bag.
To help avoid the possib ility of injury, please
follow these guidelines:
(1) Always sit as upright as possible, prop- erly use the seat belts and use an appro-
priately sized infant or child restraint
system for all children 12 years old or
under.
(2) Always wear seat belts properly.
W463.boo Seite 71 Montag, 19. November 2007 8:41 08

72 Safety and Security
Occupant safety
Safety guidelines for the seat belt,
emergency tensioning device and air
bagiAir bags are designed to deploy only in
certain frontal impacts (front air bags) and in
side impacts (window curtain air bags) which
exceed preset thresholds. Only during these
events will they provide their supplemental
protection.
The driver and passenger should always wear
their seat belts. Otherwis e it is not possible for
the air bags to provide their supplemental pro-
tection.
In case of other types of impacts and impacts
below air bag deployment thresholds, air bags
will not deploy. The driver and passenger will
then be protected to the extent possible by a
properly fastened seat belt. A properly fastened
seat belt is also needed to provide the best
possible protection in a rollover.
We caution you not to rely on the presence of the
air bags in order to avoid wearing your seat belt.
It is important to your safety and that of your pas-
senger that you replace deployed air bags and
repair any malfunctioning air bags to make sure
the vehicle will continue to provide supplemental
crash protection for occupants.
Warning!G

Damaged seat belts or seat belts that
were highly stressed in an accident
must be replaced and their anchoring
points must also be checked. Use only
seat belts installed or supplied at an au-
thorized Mercedes-Benz Light Truck
Center.

Air bags and Emergency Tensioning
Devices (ETDs) are designed to function
on a one-time-only basis. An air bag or
ETD that has deployed must be
replaced.

Do not pass seat belt s over sharp edges.
They could tear.

Do not make any modification that could
change the effectiveness of the seat
belts.

Do not bleach or dye seat belts as this
may severely weaken them. In a crash
they may not be able to provide ade-
quate protection.

No modifications of any kind may be
made to any components or wiring of
the SRS. This includes changing or
removing any component or part of the
SRS, the installation of additional trim
material, badges, etc. over the steering
wheel hub, front passenger front air bag
cover, outboard sides of the front seat
backrests, door trim panels, or door
frame trims, and installation of
additional electrical/electronic equip-
ment on or near SRS components and
wiring. Keep area between air bags and
occupants free from objects (e.g. pack-
ages, purses, umbrellas, etc.).

Air bag system components will be hot
after an air bag has inflated. Do not
touch.

Never place your feet on the instrument
panel, dashboard, or on the seat. Always
keep both feet on the floor in front of the
seat.
W463.boo Seite 72 Montag, 19. November 2007 8:41 08

88 Safety and Security
Driving safety systems
Continuous steady brake pedal pressure
yields the advantages provided by the ABS,
namely braking power and the ability to
steer the vehicle.
On slippery road surfaces, the ABS will
respond even to light brake pressure. The
pulsating brake pedal can be an indication
of hazardous road conditions and func-
tions as a reminder to take extra care while
driving.
The - indicator lamp in the instrument
cluster (
page 26) comes on when you
turn the SmartKey to position 2. It goes
out when the engine is running. Braking
At the instant one of the wheels is about to
lock up, a slight pulsation can be felt in the
brake pedal, indicating
that the ABS is in
the regulating mode.
Keep firm and steady pressure on the
brake pedal while experiencing the
pulsation. Emergency brake maneuver
Keep continuous full pressure on the
brake pedal.
Warning!G
When the ABS is malf
unctioning, the BAS,
the EBB, the ESP®, and the 4-ETS are also
switched off. The basic driving and braking
functions are still available.
When the ABS is malfunctioning, the wheels
may lock during hard braking, reducing
steering capability and extending the brak-
ing distance.
W463.boo Seite 88 Montag, 19. November 2007 8:41 08

89
Safety and Security
Driving safety systems
LOW RANGE– ABS
During off-road driving a special low range
system for the Antilock Brake System
(ABS) is operational with transfer case in
position LOW (
page 170).
An improved braking action (dig-in effect)
is obtained for vehicle speeds up to
37 mph (60 km/h) through a change in the
ABS control function.
For more information, see “Practical hints”
(
page 324).
BAS
The Brake Assist System (BAS) operates in
emergency situations. If you apply the
brakes very quickly, the BAS automatically
provides full brake boost, thereby poten-
tially reducing braking distance. Apply con-
tinuous full braking pressure until the
emergency braking situation is over. The
ABS will prevent the wheels from locking.
When you release the brake pedal the
brakes function again as normal. The BAS
is then deactivated.
With the BAS malfunctioning, the ABS,
ESP
®, and 4-ETS are also switched off.
Warning!G
The ABS cannot prevent the natural laws of
physics from acting on the vehicle, nor can
it increase braking or steering efficiency
beyond that afforded by the condition of the
vehicle brakes and tires or the traction
afforded. The ABS cannot prevent acci-
dents, including th ose resulting from
excessive speed in turn s, following another
vehicle too closely, or hydroplaning. Only a
safe, attentive, and skillful driver can pre-
vent accidents. The capabilities of an ABS
equipped vehicle must never be exploited in
a reckless or dangerous manner which
could jeopardize the user’s safety or the
safety of others.
Warning!G
If the BAS is malfunctioning, the brake
system is still functi oning normally, but
without the additional brake boost available
that BAS would normally provide in an emer-
gency braking maneuver. Therefore, the
braking distance may increase.
W463.boo Seite 89 Montag, 19. November 2007 8:41 08

91
Safety and Security
Driving safety systems
For more information, see “Practical hints”
(
page 330).
EBB
The Electronic Brake Booster (EBB)
enhances braking effectiveness by allow-
ing the rear brakes to supply a greater
proportion of the braking
effort in straight
line braking circumstances without a loss
of vehicle stability.
For more information, see the “Practical
hints” section (
page 327).
ESP®
The Electronic Stability Program (ESP®) is
operational as soon as the engine is run-
ning and monitors the vehicle’s traction
(force of adhesive friction between the
tires and the road surface) and handling.
The ESP
® recognizes when a wheel is
spinning or if the vehicle starts to skid.
By applying the brakes to the appropriate
wheel and by limiting engine output, the
ESP
® works to stabilize the vehicle.
The ESP® is especially useful while driving
off and on wet or slippery road surfaces.
The ESP
® also stabilizes the vehicle during
braking and steering maneuvers.
The ESP
® warning lamp v in the instru-
ment cluster (
page 26) flashes when the
ESP® is engaged.
The ESP
® warning lamp v comes on
when you switch on ignition (
page 39).
It goes out when the engine is running.
!Operational or performance test must only
be conducted on a two-axle dynamometer. If
such tests are necessary, contact an authorized
Mercedes-Benz Light Truck Center. You could
otherwise seriously damage the brake system or
the transfer case which is not covered by the
Mercedes-Benz Limited Warranty.
!Because the ESP® operates automatically,
the engine and ignition must be shut off
(SmartKey in starter switch position 0 or 1)
when testing the parking brake on a brake test
dynamometer and such testing should be no
longer than 10 seconds.
Active braking action through ESP
® may
otherwise seriously damage the brake system
which is not covered by the Mercedes-Benz
Limited Warranty.
Warning!G
If the EBB is malfun ctioning, the brake
system is still functionin g. However, the rear
wheels may lock during hard braking, caus-
ing you to lose control over the vehicle and
possibly causing an accident. Adjust your
driving style to the non-operating status of
the EBB.
W463.boo Seite 91 Montag, 19. November 2007 8:41 08