Page 243 of 293
Changing the bulbs
2403
Bulb
X Lightly press bulb 3, turn it anti-clockwise
and pull it out.
X Insert the new bulb and, applying slight
pressure, turn it clockwise until it engages.
X Fit lens 2.
X Replace and tighten screws 1.
i Do not fasten screws 1too tightly. Oth-
erwise, you could damage lens 2. Changing the rear bulbs
Changing the tail lamps X
Switch off the lights. 1
Screws
2 Lens
X Remove screws 1.
X Remove lens 2. 3
Turn signal lamp
4 Brake/tail lamp
5 Rear/parking lamp
X Lightly press the corresponding bulb into
the bulb holder, turn it anti-clockwise and
remove it from the bulb holder.
X Insert the new bulb into the bulb holder and
turn it clockwise until it engages.
! When fitting the lens, make sure that the
seal is positioned correctly. Practical advice
463_AKB; 1; 8, en-GB
wobuchh
, Version: 2.10.6
2008-07-17T15:19:41+02:00 - Seite 240 Dateiname: 6515_4091_02_buchblock.pdf; preflight
Page 244 of 293
Changing the bulbs
241
Changing the bulbs in the tail lamp/rear
foglamp 1
Screws
2 Lens
X Switch off the lights.
X Remove screws 1.
X Remove lens 2. 3
Bulb
X Lightly press bulb 3into the bulb holder,
turn it anti-clockwise and remove it from
the bulb holder.
X Insert the new bulb into the bulb holder and
turn it clockwise until it engages.
Changing the bulbs in the licence plate
lamps X
Switch off the lights. 1
Screws
2 Bulb holder with lens
X Remove screws 1.
X Remove bulb holder 2. 3
Bulb Practical advice
463_AKB; 1; 8, en-GB
wobuchh,
Version: 2.10.6 2008-07-17T15:19:41+02:00 - Seite 241 ZDateiname: 6515_4091_02_buchblock.pdf; preflight
Page 255 of 293
Towing and tow-starting
252
The jump-starting terminals are on the left-
hand side in the engine compartment when
viewed in the direction of travel. 1
Cover
2 Positive terminal (+)
3 Negative terminal (-)
X Lift up the cover of positive terminal 2on
your own vehicle.
X Connect positive terminal 2on your vehi-
cle to positive terminal of the donor battery
using the jump lead, beginning with your
own battery.
X Start the engine of the donor vehicle and
run it at idling speed.
X Connect negative terminal 3of the donor
battery to negative terminal of your vehi- cle's battery using the jump lead, connect-
ing the jump lead to the donor battery first.
X Start the engine.
X Electrical consumers can be switched on
again. Do not switch the lights on, however,
as this will overload the battery.
X Remove the jump lead from the negative
terminals 3first, and then from the posi-
tive terminals 2, each time disconnecting
from the battery on your own vehicle first.
X Have the battery checked at a qualified
specialist workshop, e.g. a Mercedes-Benz
Service Centre. Towing and tow-starting
Points to remember
G
Risk of accident
If you have the vehicle towed, you must use
a rigid towing bar if:
R the engine is not running.
R there is a brake system malfunction.
R there is a malfunction in the voltage sup-
ply or the vehicle's electrical system.
The electric power steering and the brake
force booster do not work when the engine
is not running. Greater braking force will
then be required and brake pedal travel will
be longer. If necessary, depress the brake
pedal with full force.
Do not tow the vehicle if the key cannot be
turned in the ignition lock. If this is the case,
the steering is locked and the vehicle can-
not be steered.
If you tow or tow-start another vehicle, its
weight must not exceed the maximum per-
missible gross vehicle weight of your vehi-
cle.
It is better to have the vehicle transported
than to have it towed. Practical advice
463_AKB; 1; 8, en-GB
wobuchh
, Version: 2.10.6
2008-07-17T15:19:41+02:00 - Seite 252 Dateiname: 6515_4091_02_buchblock.pdf; preflight
