2008 MERCEDES-BENZ CLS63AMG display

162 Controls in detail
Control system
You can temporarily deactivate the de-
layed shut-off feature:
Before exiting the vehicle, turn the
SmartKey in the starter switch to
position0.
Then turn it to position2 and back to
position0.
The delayed shut-off feature is deacti-
vated. It will reactivate as soon as you
reinsert the SmartKey in the starter
switch.
Vehicles with KEYLESS-GO*:
Press the KEYLESS-GO start/stop but-
ton on the gear selector lever
(
page 39).Setting interior lighting delayed shut-off
Use this function to set whether you would
like the interior lighting to remain lit during
darkness for 10 seconds after you have
removed the SmartKey from the starter
switch.
Move the selection marker with
buttonæ orç to the
Lighting
submenu.
Press buttonj ork repeatedly
until the message
Interior Lighting
Delayed Shut-off
appears in the mul-
tifunction display.
The selection marker is on the current
setting.
Press buttonæ orç to switch
the interior lighting delayed shut-off
feature
On or Off.
Vehicle submenu
Access the
Vehicle submenu via the
Settings
menu. Use the Vehicle sub-
menu to make general vehicle settings.
The following functions are available:
FunctionPage
Setting automatic locking163
Audio search function163

163 Controls in detail
Control system
Setting automatic locking
Use this function to activate or deactivate
the automatic central locking. With the au-
tomatic central locking system activated,
the vehicle is centrally locked at vehicle
speeds of approximately 9 mph
(15 km/h).
Move the selection marker with the
æ or çbutton to the
Vehicle
submenu.
Press buttonj ork repeatedly
until the message
Automatic Door
Locking
appears in the multifunction
display.
The selection marker is on the current
setting.
Press buttonæ orç to switch
Automatic Door Locking On or Off.Setting station selection mode
Use the
Audio Search Function to select
the manual or memory station selection
mode for the radio (
page 148).
Move the selection marker with the
æ or çbutton to the
Vehicle
submenu.
Press buttonj ork repeatedly
until the message
Audio Search Func-
tion
appears in the multifunction dis-
play.
The selection marker is on the current
setting.
Pressæ orç to select the de-
sired station selection mode. You can
select:

Frequenc.

Memory selects next stored station
Convenience submenu
Access the
Convenience submenu via the
Settings menu. Use the Convenience
submenu to activate the easy-entry/exit
feature.
Activating easy-entry/exit feature
Use this function to activate and deacti-
vate the easy-entry/exit feature
(
page 45).

165 Controls in detail
Control system
Fuel consumption statistics since start
Press buttonÿ orè repeatedly
until the first function of the trip com-
puter menu appears.
Press buttonj ork repeatedly
until the message
From Start appears
in the multifunction display.
1Distance driven since start
2Time elapsed since start
3Average speed since start
4Average fuel consumption since start
Fuel consumption since last reset
Press buttonÿ orè repeatedly
until the first function of the trip com-
puter menu appears.
Press buttonj ork repeatedly
until the message
From Reset appears
in the multifunction display.
1Distance driven since last reset
2Time elapsed since last reset
3Average speed since last reset
4Average fuel consumption since last
resetResetting fuel consumption statisticsPress buttonÿ orè repeatedly
until the first function of the trip com-
puter menu appears.
Press buttonj ork repeatedly
until the reading that you want to reset
in the multifunction display appears.
Press and hold the reset button
(
page 136) until the value is reset
to
0.
iAll statistics stored since the last engine
start will be reset approximately 4 hours after
the SmartKey in the starter switch is turned to
position0 or removed from the starter switch.
Resetting will not occur if you turn the SmartKey
back to position1 or2 within this time period.

166 Controls in detail
Control system
Distance to empty
Press buttonÿ orè repeatedly
until the first function of the trip com-
puter menu appears.
Press buttonj ork repeatedly
until the message
Range: appears in
the multifunction display.
The calculated remaining driving range
based on the current fuel tank level ap-
pears in the multifunction display.
TEL* menu
You can use the functions in the
Tel menu
to operate your telephone, provided it is
connected to a hands-free system and
switched on.
Switch on the telephone and COMAND.
Press buttonÿ orè on the
steering wheel repeatedly until the
Tel
menu appears in the multifunction dis-
play.iIf only very little fuel is left in the tank, a ve-
hicle at the fuel pump is shown instead of the
range.
Warning!G
A driver’s attention to the road must always
be his/her primary focus when driving. For
your safety and the safety of others, we rec-
ommend that you pull over to a safe location
and stop before placing or taking a tele-
phone call. If you choose to use the tele-
phone while driving, please use the
hands-free device and only use the tele-
phone when weather, road and traffic condi-
tions permit.
Some jurisdictions prohibit the driver from
using a cellular telephone while driving a
vehicle.
Bear in mind that at a speed of just 30 mph
(approximately 50 km/h), your vehicle is
covering a distance of 44 feet (approximate-
ly 14 m) every second.
Never operate radio transmitters equipped
with a built-in or attached antenna (i.e. with-
out being connected to an external antenna)
from inside the vehicle while the engine is
running. Doing so could lead to a malfunc-
tion of the vehicle’s electronic system, pos-
sibly resulting in an accident and/or
personal injury.

167 Controls in detail
Control system
Which messages will appear in the multi-
function display depends on whether your
telephone is switched on or off:

If the telephone is off, the message in
the multifunction display is:
TEL off.

If the telephone is on:
The telephone will then search for a
network. During this time the multi-
function display is empty.
As soon as the telephone has found a
network,
READY appears in the multi-
function display.
This standby message indicates that your
telephone is ready for use and you can
operate it using the control system.Answering a call
When your telephone is ready to receive
calls, you can answer a call at any time. In
the multifunction display you will then see
the message or if supported, the caller ID
(name and number):
Press buttons.
You have answered the call. In the mul-
tifunction display you see the length of
the call.
Ending and rejecting a call
Press buttont.Dialing a number from the phone book
If your telephone is ready to receive calls,
you may select and dial a number from the
phone book at any time.
Press buttonÿ orè repeatedly
until the
Tel menu appears in the
multifunction display.
Press buttonj ork.
The control system reads the phone
book which is stored in the telephone.
This may take several minutes. In the
multifunction display you will see the
message
Please Wait.
When the message
Please Wait dis-
appears, the phone book has been
loaded.
Press buttonj ork repeatedly
until the desired name appears in the
multifunction display.
The stored names are displayed in as-
cending or descending alphabetical
order.


168 Controls in detail
Control system
Press buttons.
The system dials the selected phone
number.

If the connection is successful, the
name of the party you called and
the duration of the call will appear
in the multifunction display.

If no connection is made, the con-
trol system stores the dialed num-
ber in the redial memory.Redialing
The control system stores the most recent-
ly dialed phone numbers. This eliminates
the need to search through your entire
phone book.
Press buttonÿ orè repeatedly
until the
Tel menu appears in the mul-
tifunction display.
Press buttons.
In the multifunction display the first
number in the redial memory appears.
Press buttonj ork repeatedly
until the desired name appears in the
multifunction display.
Press buttons.
The control system dials the selected
phone number.
iIf you press and holdj ork for long-
er than 1 second, the system scrolls rapidly
through the list of names until you release the
button again.
Cancel the quick search mode by pressingt.

169 Controls in detail
Automatic transmission
Automatic transmission
For more information on driving with an
automatic transmission, see “Automatic
transmission” (
page 51).
Your vehicle’s transmission adapts its gear
shifting process to your individual driving
style by continually adjusting the shift
points up or down. These shift point adjust-
ments are performed based on current
operating and driving conditions.
If the operating conditions change, the
automatic transmission reacts by
adjusting its shift program.
Gear selector lever
The gear selector lever is located on the
lower part of the center console.
Gearshift pattern for automatic
transmission
PPark position
RReverse gear
NNeutral
DDrive position
iDuring the brief warm-up, transmission
upshifting is delayed. This allows the catalytic
converter to heat up more quickly to operating
temperature.
Warning!G
Make sure that absolutely no objects are ob-
structing the pedals’ range of movement.
Keep the driver’s footwell clear of all obsta-
cles. If there are any floormats or carpets in
the footwell, make sure that the pedals still
have sufficient clearance.
During sudden driving or braking maneuvers
the objects could get caught between the
pedals. You could then no longer brake or
accelerate. This could lead to accidents and
injury.
iThe current gear selector lever positionP,
R,N orD appears in the multifunction display
(
page 171).

171 Controls in detail
Automatic transmission
Gear selector lever positions
The current gear selector lever position
appears in the multifunction display.
1Current gear selector lever positionEffect
ìPark position
Gear selector lever position
when the vehicle is parked. Place
gear selector lever in park
positionP only when vehicle is
stopped. The park position is not
intended to serve as a brake
when the vehicle is parked.
Rather, the driver should always
set the parking brake in addition
to placing the gear selector lever
in park positionP to secure the
vehicle.
Effect
The SmartKey can only be
removed from the starter switch
with the gear selector lever in
park positionP. With the
SmartKey removed, the gear
selector lever is locked in park
positionP.
If the vehicle’s electrical system
is malfunctioning, the gear
selector lever could remain
locked in park positionP
(
page 400).
íReverse gear
Place gear selector lever in
positionR only when vehicle is
stopped.