2008 MERCEDES-BENZ CLK63AMG wheel alignment

422 Practical hints
Where will I find...?
TIREFIT (CLK 63 AMG only)
The TIREFIT kit is located under the trunk
floor.
Lift up trunk floor cover and engage the
handle in the upper edge of trunk
(
page 421).
1Straps for soft top emergency opera-
tion, a pair of gloves
2Electric air pump
3Towing eye bolt
4Vehicle jack
5TIREFIT kit
6Wheel wrench
7Collapsible wheel chock
Vehicle tool kit
The vehicle tool kit is located in the storage
compartment underneath the trunk floor.
The following is included:

Towing eye bolt

Wheel wrench

Alignment bolt

Vehicle jack

Collapsible wheel chock

A pair of gloves

Straps for soft top emergency opera-
tion (CLK cabriolet only)
The spare wheel bolts are fixed at the
Minispare wheel.Removing the vehicle tool kit
Lift up trunk floor cover and engage the
handle in upper edge of trunk
(
page 421).
Example CLK coupe
1Retaining screw
2Storage well casing
Loosen retaining screw1 in the mid-
dle of storage well casing2 by turning
it counterclockwise.
Remove storage well casing2.
i(CLK cabriolet) Hex wrench:
You will find the hex wrench for manually operat-
ing the roll bars (
page 430) or the soft top
(
page 432) at the lower edge of the storage
well casing.

458 Practical hints
Flat tire
Drive to the nearest qualified work-
shop, e.g. an authorized
Mercedes-Benz Center, to have the
damaged tire replaced.
Recommended duration of use:
A maximum of 300 miles (500 km) at
50 mph (80 km/h) or below with the
recommended tire inflation pressure.
Contact an authorized Mercedes-Benz
Center as soon as possible to obtain a
new TIREFIT kit.
Bring used TIREFIT materials to an
authorized Mercedes-Benz Center for
proper disposal.
Replace your TIREFIT container every
4 years. Replacement containers are
available at your authorized
Mercedes-Benz Center.
Mounting the Minispare wheel Preparing the vehicle
Prepare the vehicle as described
(
page 452).
Take the wheel wrench, alignment bolt,
collapsible wheel chock, and the jack
out of the trunk (
page 422).
Take the Minispare wheel and wheel
bolts out of the trunk (
page 425).
Warning!G
The dimensions of the Minispare wheel is
different from those of the road wheels. As
a result, the vehicle handling characteristics
change when driving with a Minispare wheel
mounted. Adapt your driving style
accordingly.
The Minispare wheel is for temporary use
only. When driving with a Minispare wheel
mounted, ensure proper tire pressure and
do not exceed a vehicle speed of 50 mph
(80 km/h).
Drive to the nearest Mercedes-Benz Center
as soon as possible to have the Minispare
wheel replaced with a regular road wheel.
Never operate the vehicle with more than
one Minispare wheel mounted.
Do not switch off the ESP
® when a
Minispare wheel is mounted.


460 Practical hints
Flat tire
2Jack
3Take-up bracket
Place jack2 on firm ground.
Position jack2 under take-up
bracket3 so that it is always vertical
(plumb-line) as seen from the side,
even if the vehicle is parked on an
incline.
Jack up the vehicle until the wheel is a
maximum of 1.2 in (3 cm) from the
ground. Never start engine while
vehicle is raised.Removing the wheel
1Alignment bolt
Unscrew upper-most wheel bolt and
remove.
Replace this wheel bolt with alignment
bolt1 supplied in the tool kit.
Remove the remaining bolts.
Remove the wheel.
Warning!G
The jack is intended only for lifting the
vehicle briefly for wheel changes. It is not
suited for performing maintenance work
under the vehicle.

Never start the engine when the vehicle
is raised.

Never lie down under the raised vehicle.
!Do not place wheel bolts in sand or dirt. This
could result in damage to the bolts and wheel
hub threads.

461 Practical hints
Flat tire
Mounting the Minispare wheel
1Wheel bolt for light alloy rims
2Wheel bolt for Minispare wheel,
(located in trunk with Minispare wheel)Clean contact surfaces of wheel and
wheel hub.
1Alignment bolt
Guide spare wheel onto the alignment
bolt and push it on.
Insert wheel bolts and tighten them
slightly.!Wheel bolts2 must be used when mount-
ing the Minispare wheel. The use of any wheel
bolts other than wheel bolts2 for the Minispare
wheel will physically damage the vehicle’s
brakes.
!To avoid paint damage, place wheel flat
against hub and hold it there while installing first
wheel bolt.
Warning!G
Always replace wheel bolts that are
damaged or rusted.
Never apply oil or grease to wheel bolts.
Damaged wheel hub threads should be
repaired immediately. Do not continue to
drive under these circumstances! Contact
an authorized Mercedes-Benz Center or call
Roadside Assistance.
Incorrect wheel bolts or improperly tight-
ened wheel bolts can cause the wheel to
come off. This could cause an accident.
Make sure to use the correct wheel bolts.


462 Practical hints
Flat tire
Unscrew the alignment bolt, install last
wheel bolt and tighten slightly.Lowering the vehicle
Lower vehicle by turning crank
counterclockwise until vehicle is
resting fully on its own weight.
Remove the jack.
1 - 5 Wheel bolts
Tighten the five wheel bolts evenly,
following the diagonal sequence
illustrated (1to5), until all bolts are
tight. Observe a tightening torque
of 80 lb-ft (110 Nm).
Before storing the jack, it should be fully
collapsed, with handle folded in (storage
position) (
page 424).
Store the jack and the other vehicle
tools in the trunk.
Warning!G
Only use genuine Mercedes-Benz wheel
bolts. Other wheel bolts may come loose.
Do not tighten the wheel bolts when the
vehicle is raised. Otherwise the vehicle
could fall off the jack.
Warning!G
Have the tightening torque checked after
changing a wheel. The wheels could come
loose if they are not tightened to a torque
of 80 lb-ft (110 Nm).