2008 MERCEDES-BENZ CLK63AMG start stop button

400 Practical hints
What to do if …?
Display messagePossible cause/consequencePossible solution
PSelector Lever
In ParkYou have turned off the engine with the
KEYLESS-GO* start/stop button in gear
selector lever positionN and opened the
driver’s door.
or
You have attempted to switch off the en-
gine with the KEYLESS-GO* start/stop
button while the gear selector lever was in
positionR orD.Place the gear selector lever in
positionP.
Please Shift To
N or PYou have attempted to start the engine
with the KEYLESS-GO* start/stop button
while the gear selector lever was in
positionR orD.Place the gear selector lever in
positionP or N.
Run Flat Indicator
InoperativeRun Flat Indicator is malfunctioning.Have the Run Flat Indicator checked
at an authorized Mercedes-Benz
Center.
Check tires,
then restart
Run Flat Indicator.There was a warning message about a
loss in the tire inflation pressure and the
Run Flat Indicator has not been reactivat-
ed yet.Make sure the correct tire inflation
pressure is set for each tire.
Then restart the Run Flat Indicator.

427 Practical hints
Unlocking/locking in an emergency
Unlocking/locking in an emergency
Unlocking the vehicle
If you are unable to unlock the vehicle with
the SmartKey or KEYLESS-GO*, open the
driver’s door and the trunk using the
mechanical key.
1Mechanical key locking tab
2Mechanical key
Move locking tab1 in the direction of
arrow.
Slide mechanical key2 out of the
housing.Unlocking the driver’s doorInsert the mechanical key2 into the
driver’s door lock until it stops.
Turn the mechanical key2 counter-
clockwise to position1 until the lock-
ing knob moves up.
The driver’s door is unlocked.
Pull the door handle to open the
driver’s door.
iUnlocking and opening the driver’s door
and/or the trunk with the mechanical key will
trigger the anti-theft alarm system.
To cancel the alarm, do one of the following:

Press button Œ or ‹on the
SmartKey.

Insert the SmartKey in the starter switch.
Vehicles with KEYLESS-GO*:

Pull the outside door handle.

Press the KEYLESS-GO* start/stop button
(
page 39).
1Unlocking
2Mechanical key

452 Practical hints
Flat tire
The CLK 63 AMG is equipped with a
TIREFIT kit.
Preparing the vehicle
Park the vehicle in a safe distance from
moving traffic on a hard, flat surface
when possible.
Turn on the hazard warning flasher
(
page 135).
Turn the steering wheel so that the
front wheels are in a straight ahead
position.
Set the parking brake (page 59).
Move the gear selector lever toP.
Vehicles with SmartKey:
Turn off the engine (page 60).
Remove the SmartKey from the starter
switch.Vehicles with SmartKey with
KEYLESS-GO*:
Turn off the engine by pressing the
KEYLESS-GO* start/stop button on the
gear selector lever once (
page 60).
Open the driver’s door (with driver’s
door open, starter switch is now in
position0, same as with SmartKey re-
moved from starter switch). The driv-
er’s door then can be closed again.
Have any passenger exit the vehicle at
a safe distance from the roadway.Sealing tires with TIREFIT
(CLK 63 AMG only)
Small tire punctures, particularly those in
the tread, can be sealed with TIREFIT.
TIREFIT can be used in ambient tempera-
tures down to -4°F (-20°C).
iOpen door only when conditions are safe to
do so.
Warning!G
TIREFIT is a limited repair device. TIREFIT
cannot be used for cuts or punctures larger
than approximately 0.16 in (4 mm) and tire
damage caused by driving with extremely
low tire inflation pressure, or on a flat tire, or
a damaged wheel.
Do not drive the vehicle under such circum-
stances.
Contact the nearest Mercedes-Benz Center
for assistance or call Roadside Assistance.

455 Practical hints
Flat tire
Version 1
aVent screw
bPressure gauge
Close vent screwa on pressure
gaugeb (version 1 only).
Screw filler hose8 onto tire valve9.
Insert electrical plug4 into the ciga-
rette lighter (
page 290) or the power
outlet in the rear passenger compart-
ment (
page 291).
Turn the SmartKey in the starter switch
to position1 (
page 38).
Vehicles with KEYLESS-GO*:
Press the KEYLESS-GO* start/stop
button (
page 40) on the gear se-
lector lever once. Do not depress
brake pedal.
PressI on electric air pump switch3.
The electric air pump is switched on
and inflates the tire.
Let the electric air pump inflate the tire
for approximately 5 minutes.
The pressure gauge must display at
least 26 psi (1.8 bar). The air hose can
become hot during inflation.
Please exercise appropriate caution.
If the tire inflation pressure of at least
26 psi (1.8 bar) is not attained, turn off
the electric air pump by pressing0 on
electric air pump switch3
(
page 454).
Detach filler hose8 from tire valve9
(
page 454).
Drive vehicle back and forth very slowly
approximately 30 ft (10 m).
This serves to better distribute the
TIREFIT sealant material inside the tire.
Unscrew the air pump’s air hose5
from flange6 of TIREFIT container1
(
page 454).
Screw air hose5onto tire valve9.
Inflate the tire again.
iFirst, the sealing is pumped into the tire. The
pressure may briefly rise to up to 73 psi (5 bar).
This is normal and not an indication of a malfunc-
tion. Do not switch off the electric air pump.
!Do not operate the electric air pump longer
than 6 minutes without interruption. Otherwise it
may overheat.
You may operate the air pump again after it has
cooled off.


456 Practical hints
Flat tire
After attaining a tire inflation pressure
of 26 psi (1.8 bar), press0 on electric
air pump switch3 (
page 454).
The electric air pump is switched off.
Turn the SmartKey in the starter switch
to position0 (
page 38).
Vehicles with KEYLESS-GO*:
Press the KEYLESS-GO* start/stop
button (
page 40) on the gear
selector lever twice. Do not depress
brake pedal.
Detach the electric air pump.
The air hose may still be hot. Please
exercise appropriate caution.
Place the electrical air pump back in
the trunk.
Close the trunk.
Drive off immediately.
The TIREFIT sealant will distribute itself
evenly inside the tire.
After driving the vehicle for an initial
10 minutes, check the tire inflation
pressure using pressure gauge b on
the air pump.
Warning!G
If a tire inflation pressure of 26 psi (1.8 bar)
is not attained, the tire is too severely
damaged for TIREFIT to provide a reliable
tire repair.
In this case, TIREFIT cannot properly seal
the tire.
Do not drive the vehicle.
Contact the nearest Mercedes-Benz Center
or call Roadside Assistance.
Warning!G
Do not exceed vehicle speed of
50 mph (80 km/h). A TIREFIT repair is not
designed to operate at higher speeds.
The sticker must be attached on the instru-
ment cluster where it will be easily seen by
the driver.
Vehicle handling characteristics of a TIREFIT
repaired tire may change. Adapt your driving
accordingly.


465 Practical hints
Battery
2Negative terminal
3Positive terminal cover
Disconnecting the battery
Apply the parking brake (page 59).
Make sure gear selector lever is set to
positionP (
page 174).
Turn off all electrical consumers.
Remove SmartKey from starter switch.
Vehicles with KEYLESS-GO*:
Press the start / stop button until
the engine shuts off.
Open the driver’s door.
Open the hood (page 323).
Remove the filter box (page 464).
Read and observe safety instructions
and precautions (
page 464).
Disconnect the battery negative lead
from negative terminal2.
Remove cover3 from the positive
terminal.
Disconnect the battery positive lead.
Removing the battery
Remove the screw securing the
battery.
Remove the battery support and
bracket.
Pull out the ventilation hose from the
battery (depending on battery arrange-
ment in your vehicle model, the ventila-
tion hose is located either on the left or
right side of the battery).
Take out the battery.
Warning!G
With a disconnected battery

you will no longer be able to turn the
SmartKey in the starter switch and
pressing the KEYLESS-GO* start/stop
button on the gear selector lever will
have no effect

the gear selector lever will remain
locked in positionP
!Always disconnect the battery in the order
described below. Otherwise the vehicle’s elec-
tronics can be damaged.

470 Practical hints
Towing the vehicle
Installing towing eye bolt
Towing eye bolt CLK 350
1Cover on right side of front bumper2Cover on right side of rear bumper
To remove cover:
Press mark on cover 1 or 2.
Lift cover off to reveal the threaded
hole for towing eye bolt.
The towing eye bolt is supplied with the
tool kit (located in the compartment under-
neath the trunk floor).
Screw towing eye bolt in to its stop and
tighten with wheel wrench.
To reinstall cover:
Fit cover 1 or 2 and snap into place.
!Towing of the vehicle should only be done
using the properly installed towing eye bolt.
Never attach tow cable, tow rope or tow rod to
the vehicle chassis, frame or suspension parts.
iWhen towing the vehicle with all wheels on
the ground, please note the following:
With the automatic central locking activated and
the SmartKey in starter switch position2, or
KEYLESS-GO* start/stop button in position2,
the vehicle doors lock if the left front wheel as
well as the right rear wheel are turning at vehicle
speeds of approximately 9 mph (15 km / h) or
more.
To prevent the vehicle door locks from locking,
deactivate the automatic central locking
(
page 166).
iTo signal turns while being towed with the
hazard warning flasher in use, switch on the
ignition and activate the combination switch for
the left or right turn signal in the usual manner –
only the selected turn signal will operate.
Upon canceling the turn signal, the hazard
warning flasher will operate again.
iIf the battery is disconnected or discharged

the SmartKey will not turn in the starter
switch. For more information, see “Battery”
(
page 464) and “Jump starting”
(
page 467).

the gear selector lever will remain locked in
positionP. For information on manually un-
locking the transmission gear selector lever,
see (
page 429).

506 Index
K
Key, Mechanical 427
Key, SmartKey 100
Batteries 108
Battery check lamp 102, 107
Changing batteries 442
Factory setting 102, 103
Ignition 38
Locking/unlocking 36, 62, 100
Locking/unlocking,
Global setting 102
Locking/unlocking,
Selective setting 102
Loss of 109
Message in display 411
Opening and closing the
power tilt/sliding sunroof* 257
Opening and closing the
power windows 253
Opening and closing the soft top 263
Positions in starter switch 38
Remote control 100
SmartKey with KEYLESS-GO* 103
Starting the engine 52
Steering wheel lock 38
Turning off the engine 60Unlocking/opening trunk lid 103
KEYLESS-GO* 103
Battery check lamp, SmartKey 107
Factory setting 106, 108
Ignition 40
Important notes 105
Lock button 62
Locking/unlocking 37, 62, 103
Locking/unlocking,
Global setting 106
Locking/unlocking, Selective
setting 107
Loss of key 109
Messages in display 410
Remote control 103
Start / stop button 39
Starting the engine 52
Turning off the engine 60
Unlocking/opening trunk lid 108
Kickdown 176
Kilopascal 359L
Labels 478
Certification 478
Emission control information 479
Lamp sensor see Light sensor
Lamps, exterior 444
Light sensor 411
Messages in display 411–415
Lamps, indicator and warning
ABS 29, 378
Battery (SmartKey) 102, 107
Brakes 29, 380
Center console 390–391
CHECK ENGINE 381
Coolant 382
Coolant temperature 29, 139
Distance warning 29
Engine diagnostics 381
Engine malfunction 29, 381
ESP
®384
Fog lamps 132
Front passenger front air bag off 70
Front passenger front
air bag off indicator lamp 390
Fuel reserve 29, 385
High beam headlamp 29