2008 MERCEDES-BENZ CL-Class ignition

434 Controls in detailInstrument clusterA full view illustration of the instrument
cluster can be found in the “At a glance”
section of this manual (
page 30).
The instrument cluster is activated when
you:


open a door


switch on the ignition (
page 365)


switch on the exterior lamps
The language setting for the multifunction
display can be changed via COMAND
(
page 83).Adjusting instrument cluster display
illumination
1Knob
Brightening illumination: Turn
knob1 clockwise.

Dimming illumination: Turn knob1
counterclockwise.
Warning!
G
No messages will be displayed if either the
instrument cluster or the multifunction dis-
play is inoperative.
As a result, you will not be able to see infor-
mation about your driving conditions, such
as speed or outside temperature, warning/
indicator lamps, malfunction/warning mes-
sages or the failure of any systems. Driving
characteristics may be impaired.
If you must continue to drive, please do so
with added caution. Contact an authorized
Mercedes-Benz Center as soon as possible.
i
The instrument cluster illumination is
dimmed or brightened automatically to suit am-
bient light conditions.
The instrument cluster illumination will also be
adjusted automatically when you switch on the
vehicle’s exterior lamps.

464 Controls in detailDriving systemsThe Parktronic system is an electronic
parking aid with ultrasonic sensors that
helps you while parking.
It visually and audibly indicates the relative
distance between the vehicle and an ob-
stacle.
The Parktronic system is automatically ac-
tivated when you switch on the ignition, re-
lease the electronic parking brake or start
the engine and engage drive positionD, re-
verse gearR or neutral positionN.The Parktronic system deactivates at
speeds over approximately 11 mph
(18 km/h). At lower speeds the Parktronic
system turns on again.
The Parktronic system also deactivates
when you set the automatic transmission
to park positionP or secure the vehicle in
place with the electronic parking brake
and switch off the engine.
The Parktronic system monitors the sur-
roundings of your vehicle with six sensors
in the front bumper and four sensors in the
rear bumper.
1Sensors in the front bumper (Only visi-
ble without DISTRONIC Plus*)Range of the sensors!
The operational function of the Parktronic
system can be affected by dirty sensors, espe-
cially at times of snow and ice.
Make sure that the area on the bumpers around
the sensors is free of dirt, ice and/or slush,
otherwise the Parktronic system may not
function properly, see “Cleaning the Parktronic*
system sensors” (
page 600).
i
Interference caused by other ultrasonic sig-
nals (e.g. working jackhammers, car wash, or the
air brakes of trucks) can cause the system to
send erratic indications, and should be taken
into consideration.
i
To function properly, the sensors must be
free of dirt, ice, snow and slush. Clean the sen-
sors regularly, being careful not to scratch or
damage the sensors, see “Cleaning the Park-
tronic* system sensors” (
page 600).

467 Controls in detail
Driving systems

Switching off the Parktronic sys-
tem: Press button 1.
Indicator lamp 2 comes on.

Switching on the Parktronic system:
Press button 1 again.
Indicator lamp 2 goes out.
Parktronic system malfunction
If only the red distance segments illumi-
nate and an acoustic warning sounds,
there is a malfunction in the Parktronic
system. The Parktronic system will auto-
matically switch off after 20 seconds and
the indicator lamp in the Parktronic switch
comes on.

Have the Parktronic system checked
by an authorized Mercedes-Benz
Center as soon as possible.
If only the red distance segments illumi-
nate and no acoustic warning sounds, the
Parktronic system sensors are dirty or
there is an interference from other radio or
ultrasonic signals. The Parktronic system
will automatically switch off after 20 sec-
onds and the indicator lamp in the
Parktronic switch comes on.

Switch off the ignition (
page 365).

Clean the Parktronic system sensors
(page 600).

Switch on the ignition.
or

Check the Parktronic system operation
at another location to rule out interfer-
ence from outside radio or ultrasonic
signals.
Park Assist*
i
The Parktronic system is automatically
switched on when the ignition is switched on
(
page 365).
Warning!
G
Park Assist is a supplemental system. It is
not intended to, nor does it replace, the
need for extreme care. The responsibility
during parking and other critical maneuvers
always remains with the driver.Warning!
G
Make sure no persons or animals are in the
area in which you are maneuvering. You
could otherwise injure them.!
Special attention must be paid to objects
with smooth surfaces or low silhouettes (e.g.
trailer couplings, painted posts, elevated cross-
bars or road curbs). Such objects may not be
detected by the system and can damage the
vehicle.

471 Controls in detail
Driving systems
Collision warning
Park Assist can detect obstacles from a
considerable distance. If you drive in re-
verse towards an obstacle, you will hear a
warning tone. You must then brake in or-
der to avoid a collision. The warning tone
for a collision will not sound when the vehi-
cle is at a standstill very close to the obsta-
cle. In this case, you will hear a
corresponding tone for the warning indica-
tor in the rear area.
Switching Park Assist system on/off
The Park Assist system can be switched off
manually.
The Park Assist button with the indicator
lamp is located on the control panel on the
right-hand side of the instrument cluster.1Park Assist button
2Indicator lamp

Switching off Park Assist system:
Press button 1.
Indicator lamp 2 comes on.

Switching on Park Assist system:
Press button 1 again.
Indicator lamp 2 goes out.
Advanced Parking Guidance*
Advanced Parking Guidance is an electron-
ic parking aid equipped with radar sensors
that scan the area on both sides of vehicle.
When suitable parking space is found it is
shown in the display and you receive steer-
ing instructions for parking in that space.
i
During strong rainfall, the collision warning
may be triggered, for example, by water splash-
ing into the area of the sensors.
i
When the indicator lamp is illuminated, the
Park Assist system is switched off.
i
The Park Assist system is automatically
switched on when the ignition (
page 365) and
radar sensors are switched on (page 302).
Warning!
G
Advanced Parking Guidance is only an aid
and may display parking spaces that are not
suitable e.g. due to parking regulations, un-
suitable road/ground surfaces, driveways,
entrances/exits, etc.


480 Controls in detailDriving systemsSwitching on Rear View Camera
Switch on the ignition (
page 365).

Switch on COMAND (
page 83).

Move gear selector lever to reverse
gearR.
The COMAND display will show the
area behind the vehicle with guide
lines.1Blue guide lines for vehicle width
2Yellow 39 in (1 m) guide line
3Red 10 in (0.25 m) guide line
The red 10 in (0.25 m) guide line3, the
yellow 39 in (1 m) guide line2 corre-
spond to the relevant distance from the
rear of the vehicle. The blue guide line for
vehicle width1 show the required width
for the vehicle.Warning!
G
Use of Rear View Camera can be dangerous
if you are color-blind or have impaired color
vision.
Only use Rear View Camera if you can see
and distinguish all colored guide lines shown
by Rear View Camera on the COMAND dis-
play.i
The Rear View Camera must be activated in
the instrument cluster control system in order
for it to be switched on (
page 298).
Warning!
G
Please note that objects which do not touch
the ground, such as the bumper of a vehicle
parked behind you, a trailer hitch, or the
back of a truck, may appear to be further
away than they actually are. In this case, you
should not use the guide lines to judge dis-
tance as the use of the guide lines to judge
distance increases the risk of impacting the
objects.
Even when the object you approach is di-
rectly on the ground (and nothing on the ob-
ject extends above the ground beyond the
object’s contours directly touching the
ground) and no objects that do not touch
the ground, such as the bumper of a vehicle
parked behind you, a trailer hitch, or the
back of a truck are in the path, do not ap-
proach the object on the ground any closer
than red guide line4.

487 Controls in detail
Driving systems
Indicator and warning lamps
1Yellow indicator lamp/red warning
lamp
Switching on: Make sure that the ra-
dar sensors (
page 302) and the Blind
Spot Assist (page 299) are switched
on.
With the ignition switched on, the warn-
ing lamp1 in the exterior mirror lights
up red.
With the engine running, the indicator
lamp1 in the exterior mirror lights up
yellow up to a speed of 20 mph
(30 km/h).Once a speed above 20 mph (30 km/h)
has been reached and


Blind Spot Assist detects no vehicle in
its range, the indicator lamp1 goes
out


Blind Spot Assist detects another vehi-
cle in its range, the warning lamp1 on
the corresponding side of the vehicle
turns red.Collision warning
If a vehicle is detected in the Blind Spot As-
sist range and you activate the turn signal,
a two-tone warning will sound and the red
warning lamp1 will flash.

Remain on the lane that you are cur-
rently on until traffic conditions permit
to change.
If the turn signal remains on, the red warn-
ing lamp1 will flash to indicate that vehi-
cles have been detected. No further
audible warnings will sound.
Warning!
G
Blind Spot Assist is not active at speeds be-
low approximately 20 mph (30 km/h). You
will not be alerted to the presence of vehi-
cles in the monitored area at these speeds.
It is the driver’s responsibility at all times to
be attentive to road, weather and traffic con-
ditions and to provide the steering, braking
and other driving inputs necessary to retain
control of the vehicle. Failure to do so could
result in recognizing dangers too late, possi-
bly resulting in an accident and serious inju-
ry to yourself and others.
Warning!
G
Do not change lanes or make turns, while
the red warning lamp
1
is flashing. Doing
so could result in an accident and seroius in-
jury to yourself and others.

496 Controls in detailAutomatic climate controlRear window defroster
Activating
Switch on the ignition (
page 365).

Press button< (
page 491) up or
down.
The indicator lamp on the button
comes on.
Deactivating

Press button< (
page 491) up or
down.
The indicator lamp on the button goes
out.
Maximum cooling MAXCOOL (USA only)
If U is selected on both the left and
right side and there is a high demand for
cooling, the display “MAXCOOL” appears
in the COMAND display.
This provides the fastest possible cooling
of the vehicle interior (when windows and
tilt/sliding sunroof are closed).
Air recirculation mode
Switch to air recirculation mode to prevent
unpleasant odors from entering the vehicle
from the outside (e.g. before driving in a
tunnel). This setting cuts off the intake of
outside air and recirculates the air in the
passenger compartment.
!
The rear window defroster uses a large
amount of power. To keep battery drain to a min-
imum, switch off the defroster as soon as the
rear window is clear.
i
The defroster is automatically deactivated
after some time of operation depending on the
outside temperature.
Warning!
G
Any accumulation of snow and ice should be
removed from the rear window before driv-
ing. Visibility could otherwise be impaired,
endangering you and others.i
If the rear window defroster switches off too
soon and the indicator lamp goes out, this indi-
cates that too many electrical consumers are op-
erating simultaneously and the load on the
battery is reducing available voltage. The system
responds automatically by deactivating the rear
window defroster.
i
Maximum cooling MAXCOOL is only avail-
able when the engine is running.Warning!
G
Fogged windows impair visibility, endanger-
ing you and others. If the windows begin to
fog on the inside, switching off the air
recirculation mode immediately should clear
interior window fogging. If interior window
fogging persists, make sure the air
conditioning (
page 272) is activated, or
press button;.

499 Controls in detail
Automatic climate control
Activating
Switch off the ignition (
page 365).

Press buttonT (
page 491) up or
down.
The indicator lamp on the button
comes on.Deactivating

Press buttonT (
page 491) up or
down.
The indicator lamp on the button goes
out.
i
The residual heat is automatically turned off:


when the ignition is switched on


after approximately 30 minutes


if the battery voltage drops


if the coolant temperature is too low