2008 MERCEDES-BENZ CL-Class manual transmission

432 Controls in detailAutomatic transmissionIf you are driving in the manual program
modeM, upshift indicator2 in the multi-
function display advises you to upshift be-
fore the engine reaches the overspeed
range. Thus you can drive at the maximum
engine speed for each gear without over-
revving the engine.
1Gear indicator
2Upshift indicator “up”
3Engine oil temperature
4Vehicle supply voltage
Shift to the next higher gear.
The fuel supply will otherwise be inter-
rupted to prevent the engine from over-
revving.Downshifting

Briefly pull left shift paddle1
(page 429).
The transmission shifts to the next
lower gear.Kickdown
Using the kickdown when driving in the
manual program modeM is not possible.
Deactivating manual shift program

Press the program mode selector
switch (
page 430) repeatedly until
“C”or“S” appears in the multifunction
display.
or

Restart the engine.
The transmission will go to the
automatic program mode (C orS).
The manual program modeM is not
stored.
Warning!
G
On slippery road surfaces, never downshift
in order to obtain braking action. This could
result in drive wheel slip and reduced
vehicle control. Your vehicle’s ABS will not
prevent this type of loss of control.i
When you brake or stop, the transmission
shifts down to a gear from which you can easily
accelerate or drive off.


533 Controls in detail
Useful features
Step 7:
To program the remaining two signal
transmitter buttons, repeat the steps
above starting with step 3.
Rolling code programming
To train a garage door opener (or other
rolling code devices) with the rolling code
feature, follow these instructions after
completing the “Programming” portion
(steps 1 through 6) of this text. A second
person may make the following training
procedures quicker and easier.
Step 8:

Locate “training” button on the garage
door opener motor head unit.
Exact location and color of the button
may vary by garage door opener brand.
Depending on manufacturer, the “training” button may also be referred
to as “learn”or “smart” button. If there
is difficulty locating the transmitting
button, refer to the garage door opener
operator’s manual.
Step 9:

Press the “training” button on the ga-
rage door opener motor head unit.
The “training light” is activated.
You have 30 seconds to initiate the follow-
ing two steps.
Step 10:

Return to the vehicle and firmly press,
hold for 2 seconds and release the pro-
grammed signal transmitter button
(2, 3 or4).
Step 11:

Press, hold for 2 seconds and release
same signal transmitter button a sec-
ond time to complete the training
process.Step 12:

Confirm the garage door operation by
pressing the programmed signal trans-
mitter button (2, 3 or4).
Step 13:

To program the remaining two signal
transmitter buttons, repeat the steps
above starting with step 3.
Gate operator/Canadian programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission
which may not be long enough for the
integrated signal transmitter to pick up the
signal during programming. Similar to this
Canadian law, some U.S. gate operators
are designed to “time-out” in the same
manner.
i
If indicator lamp1 flashes rapidly for about
2 seconds and then turns to a constant light,
continue with programming steps 8 through 12
as your garage door opener may be equipped
with the “rolling code” feature.
i
Some garage door openers (or other rolling
code equipped devices) may require you to
press, hold for 2 seconds and release the same
signal transmitter button a third time to com-
plete the training process.

598 OperationVehicle careAutomatic car wash
You can have your car washed in an auto-
matic car wash from the start.
To protect the filter system, switch the
automatic climate control to air recir-
culation mode (
page 496).
If the vehicle is very dirty, prewash it be-
fore running it through the automatic car
wash.When taking the vehicle through an auto-
matic conveyor type car wash, observe the
following instructions.
Vehicles with SmartKey:

With the vehicle at a standstill and the
ignition switched on shift the
automatic transmission to neutral
positionN.

If engaged, manually release the
electronic parking brake (
page 413).

Switch off the ignition and leave the
SmartKey in the starter switch.Vehicles with KEYLESS-GO*:

With the vehicle at a standstill, depress
the brake pedal and keep it pressed.

With the ignition switched on shift the
automatic transmission to park
positionP.

Release the brake pedal.

Remove the KEYLESS-GO start/stop
button from the starter switch
(page 366).

Insert the SmartKey with KEYLESS-GO
into the starter switch.

Switch on the ignition.

Depress the brake pedal.

Shift the automatic transmission to
neutral positionN.

Release the brake pedal.

If engaged, manually release the
electronic parking brake (
page 413).

Switch off the ignition and leave the
SmartKey with KEYLESS-GO in the
starter switch.
!
Do not clean your vehicle in an automatic
touchless car wash which uses caustic spray.
Otherwise the caustic spray will damage the
paint or ornamental moldings.
!
Make sure that the windshield wiper switch
is set to0 (
page 400). Otherwise, e.g. the rain
sensor could activate and cause the wipers to
move unintentionally. This may lead to vehicle
damage.
Due to the width of the vehicle, fold in exterior
rear view mirrors prior to running the vehicle
through an automatic car wash to prevent dam-
age to the mirrors.
Warning!
G
When leaving the SmartKey or SmartKey
with KEYLESS-GO* in the starter switch, do
not leave children unattended in the vehicle.
It is possible for children to switch on the
ignition which could result in unsupervised
use of vehicle equipment. Unsupervised use
of vehicle equipment could result in an
accident and/or serious personal injury.

632 Practical hintsWhat to do if …?Display
Possible cause/consequence
Possible solution
Next Service X
Due in ... days
Due in ... mls (km)
Service X must be carried out in ... days or
after ... miles (kilometers) (
page 592).

Have the maintenance service carried out by an authorized
Mercedes-Benz Center.
Only Shift to
Position 'P' When
Vehicle Is Stationary
You have tried to Shift the automatic trans-
mission to park positionP using the gear
selector lever although the vehicle is still in
motion.

Stop your vehicle as soon as it is safe to do so.

Shift the automatic transmission to park positionP.

Engage the electronic parking brake (
page 412).
Park Assist
Currently Unavailable
See Oper. Manual
Park Assist* is deactivated because the
area around the sensors* in the front or
the rear bumper (
page 601) is dirty.

Clean the front and rear bumper (
page 601).
Park Assist* is deactivated because the
battery voltage is insufficient.

Have the battery checked by an authorized Mercedes-Benz
Center.
Park Assist* is switched off because the
radar sensor system* is temporarily inop-
erative due to electromagnetic interfer-
ence near television and radio transmitter
stations, toll stations, speed measuring
systems, etc.

Wait until the message in the multifunction display disappears.
Park Assist
Inoperative
Park Assist* is unavailable due to a mal-
function.

Contact an authorized Mercedes-Benz Center as soon as
possible.

634 Practical hintsWhat to do if …?Display
Possible cause/consequence
Possible solution
Parking Guidance
Currently Unavailable
See Oper. Manual
Advanced Parking Guidance* is deactivat-
ed because the area around the sensors*
in the front or the rear bumper
(page 601) is dirty.

Clean the front and rear bumper (
page 601).
Advanced Parking Guidance* is deactivat-
ed because the battery voltage is insuffi-
cient.

Have the battery checked by an authorized Mercedes-Benz
Center.
Advanced Parking Guidance* is switched
off because the radar sensor system* is
temporarily inoperative due to electromag-
netic interference near television and radio
transmitter stations, toll stations, speed
measuring systems, etc.

Wait to see if the interference is temporary or do not use Ad-
vanced Parking Guidance*. Try in a location where the inter-
fering transmission might not be present.
Parking Guidance
Canceled
Advanced Parking Guidance* has been
canceled because:

the vehicle is sliding


the bumper became dirty in the area of
the sensors (
page 601)


there has been a malfunction

Use Advanced Parking Guidance* again later.
If the parking space symbol is not shown in the multi-function dis-
play at a speed below 10 mph (16 km/h):

Clean the bumpers (
page 601).
or

Restart the engine.
or

Contact an authorized Mercedes-Benz Center.

650 Practical hintsWhat to do if …?Display
Possible cause/consequence
Possible solution
Parking Brake
See Oper. Manual
If overheated:
Let vehicle cool down, and do not engage
electronic parking brake during this time.
or

Switch ignition off and back on again, and en-
gage or release electronic parking brake.
(USA only)(Canada only)
Parking Brake
Inoperative
When you engage or release the electronic
parking brake, the red indicator lamp for
the electronic parking brake flashes and
goes out after approx. 10 seconds. The yel-
low warning lamp for the electronic parking
brake comes on.
The electronic parking brake is
malfunctioning.

Switch ignition off and back on again, and en-
gage electronic parking brake (
page 412).
If the electronic parking brake cannot be en-
gaged:

Shift the automatic transmission to park
positionP (
page 417).

Protect vehicle from rolling away while
parked by using a chock from the vehicle tool
kit (
page 683).

Contact an authorized Mercedes-Benz
Center as soon as possible.

711 Practical hints
Towing the vehicle
Towing with front wheels raised

Vehicles with KEYLESS-GO*: Remove
the KEYLESS-GO start/stop button
from the starter switch (
page 366).

Insert the SmartKey into the starter
switch.

Switch on the ignition.

Switch off the automatic central lock-
ing (
page 363).

Depress the brake pedal.

Shift the automatic transmission to
neutral positionN.

If engaged, manually release the
electronic parking brake.

Switch off the ignition and leave the
SmartKey in the starter switch.
Warning!
G
When leaving the SmartKey or SmartKey
with KEYLESS-GO* in the starter switch, do
not leave children unattended in the vehicle.
It is possible for children to switch on the
ignition which could result in unsupervised
use of vehicle equipment. Unsupervised use
of vehicle equipment could result in an
accident and/or serious personal injury.
!
Keep in mind that it is important for the
SmartKey to be left in starter switch with the ig-
nition switched off. As soon as the SmartKey is
removed from the starter switch the automatic
transmission will shift to park positionP.
!
Make sure that the ignition is switched off.
If the starter switch is in position2, active brak-
ing action through the ESP
® may otherwise seri-
ously damage the brake system.
!
The vehicle may be towed only for distances
up to 30 miles (50 km) and at a speed not to ex-
ceed 30 mph (50 km/h).

712 Practical hintsTowing the vehicleTowing with all wheels on the ground

Switch on the ignition.

Shift the automatic transmission to
neutral positionN.

If engaged, manually release the
electronic parking brake.
Warning!
G
If circumstances require towing the vehicle
with all wheels on the ground, always tow
with a tow bar if:

the engine will not run


there is a malfunction in the brake
system


there is a malfunction in the power sup-
ply or in the vehicle’s electrical system
This is necessary to adequately control the
towed vehicle.
Prior to towing the vehicle with all wheels on
the ground, make certain the SmartKey is in
starter switch position2.
Warning!
G
With the engine not running, there is no
power assistance for the brake and steering
systems. In this case, it is important to keep
in mind that a considerably higher degree of
effort is necessary to brake and steer the ve-
hicle. Adapt your driving accordingly.
!
Keep in mind that it is important to have the
ignition switched on. As soon as the SmartKey is
removed from the starter switch or the SmartKey
with KEYLESS-GO* is removed from the vehicle,
the automatic transmission will shift to park
positionP.
!
The vehicle may be towed only for distances
up to 30 miles (50 km) and at a speed not to ex-
ceed 30 mph (50 km/h).
i
To signal turns while being towed with the
hazard warning flasher in use, the ignition must
be switched on. You can then activate the com-
bination switch for the left or right turn signal in
the usual manner – only the selected turn signal
will operate.
Upon canceling the turn signal, the hazard warn-
ing flasher will operate again.