2008 MERCEDES-BENZ C300 Time

222 Controls in detail
Audio system
Telephone*
Safety precautionsWhen the telephone is connected via the
Bluetooth® interface to the audio system,
you can operate the telephone using the
following devices:

audio system (page 237)

Audio controller

Audio control unit

buttonss andt on the multi-
function steering wheel (
page 152)

mobile phone keypad
Please note that these functions are only
available with Mercedes-Benz approved
telephones.
Warning!G
Some jurisdictions prohibit the driver from
using a cellular telephone while driving.
Whether or not prohibited by law, for safety
reasons, the driver should not use the cellu-
lar telephone while the vehicle is in motion.
Stop the vehicle in a safe location before
placing or answering a call.
If you nonetheless choose to use the tele-
phone
1 while driving, please use the hands-
free device and be sure to pay attention to
the traffic situation at all times. Use the tele-
phone only when road, weather and traffic
conditions permit. Otherwise, you may not
be able to observe traffic conditions and
could endanger yourself and others.
1Observe all legal requirements.
Bear in mind that at a speed of just 30 mph
(approximately 50 km/h), your vehicle is
covering a distance of 44 feet (approxi-
mately 14 m) every second.
Warning!G
Never operate radio transmitters equipped
with a built-in or attached antenna (i.e. with-
out being connected to an external antenna)
from inside the vehicle while the engine is
running. Doing so could lead to a malfunc-
tion of the vehicle’s electronic system, pos-
sibly resulting in an accident and/or
personal injury.
iThe functions and services available to you
while using the telephone depend on your ser-
vice provider and the type of telephone you are
using. See also separate operating manual for in-
structions on how to use your telephone.

226 Controls in detail
Audio system
Activating Bluetooth®
Switch on the telephone
(see telephone operating instructions).
Enter the PIN (not necessary at each
telephone or network).
Activate Bluetooth® connection on the
telephone (see telephone operating in-
structions)
Press buttonh on the audio control
unit to call up the telephone mode.
Activate Bluetooth® connection on the
audio system (
page 193).
ê
System
Activate Blue-
tooth
.
You have activated or deactivated
Bluetooth
®. A checkmark appears
when Bluetooth® is activated.
Registering a telephone (authorizing)
When you use your telephone in conjunc-
tion with the audio system for the first
time, you must register (authorize) it.
It is possible to register several tele-
phones. The connection is always estab-
lished to the last activated telephone in
signal range. When you authorize a new
telephone, it is activated automatically.
You can switch between the authorized
telephones.Searching for a telephone
h
Tel
Phone List
Update.
The audio system searches for suitable
Bluetooth
® telephones within range
and enters them in the telephone list.
Authorized Bluetooth
® telephones will
be identified by a telephone-symbol in
front of the list entry once the tele-
phone list has been updated. (The sym-
bol will be grayed out if the authorized
phone is not located in the Bluetooth
®
range.)
iOn certain telephones, not only do you have
to activate the Bluetooth® function but your own
device must additionally be made “visible” for
other devices.
Each Bluetooth
® device has a Bluetooth® device
name. It is recommended to give your telephone
a personal name, by which you can clearly recog-
nize your telephone.
iIf the Bluetooth® function on the audio sys-
tem is disabled, the message
Bluetooth not
activated in system settings
appears.
iThe duration of the search procedure de-
pends on the number and type of Bluetooth®
telephones. The search may take a few minutes.
iIf the telephone list is already full (15 en-
tries), you must de-authorize one of the autho-
rized devices. Then you will start the search
again. Otherwise a new device you are looking
for will not appear in the list.
If the audio system does not find your phone, ex-
ternal authorization may be necessary
(
page 228).

229 Controls in detail
Audio system
Displaying details on a telephone
h
Tel
Phone List.
Select the telephone from the list.
Select Options
Details.
The details screen for the device is
shown in the audio display.
To close details screen:
Slideompthe audio controller or
press buttoní in the center
console.
De-authorizing a Bluetooth
® device
h
Tel
Phone List.
Select authorized device.
Select Options
De-Authorize.
A prompt appears asking whether you
really want to de-authorize this device.
Select Yes or No.
If you select
Yes, the device will be
de-authorized.Activating another telephone
If you have several authorized telephones,
you can switch between the individual tele-
phones.
When you authorize a new telephone, it is
automatically activated. Only one tele-
phone can be active at a time.
h
Tel
Phone List.
Select an authorized telephone from
the list.
Press n to confirm.
The selected phone will be searched
for and connected if it is located in the
Bluetooth
® range and Bluetooth® is ac-
tivated on the corresponding device.
The selected telephone is activated.
A dotR in front of the entry, indicates
the current active telephone in the
phone list.
Receiving business cards
You can import business cards (vCards)
into the address book from external Blue-
tooth
® devices (page 233).
iIf you de-authorize a device which has been
authorized in the past and which is not detected
in the search, this device will no longer be dis-
played in the device list.
Devices which have been authorized in the past
but which are not detected in the search are ei-
ther not switched on or not in the vehicle.
iYou cannot switch to another authorized
phone during a call.

230 Controls in detail
Audio system
TEL-Basic display
Press buttonh on the audio control
unit to call up the telephone mode.
When the connected phone is ready for op-
eration, the display will look like this:
The following information is displayed in
the status bar:

Actual time:
04:38

Bluetooth® device name of the con-
nected phone, in this case:
blue_mobil

Mobile phone network signal
strengthI. This information will
only be shown with suitable tele-
phones.The bars indicate the current signal
strength of the mobile phone network
for reception. Optimum reception is in-
dicated by all bars full. All bars empty
indicates very poor or no reception.

Receiver symbols ort.
The receiver symbol indicates whether
a call is being connected or is in
progress:
t - not active

READY indicates that a call is possible.

NO SERVICE indicates that the mobile
network is not available.Setting transmit and receive volume
h
Tel
Phone List.
Select an mobile phone from the list.
Select Options
Reception Volume
or
Transmission Volume.
To set the volume: Slideqmror
rotateymz the audio controller.
The volume bar moves up or down.
To confirm selection: Press n or
slideomp the audio controller.
iThese settings should normally not be
changed as the factory settings are matched to
most mobile phones. Find out about the opti-
mum settings for your mobile phone at an
authorized Mercedes-Benz Center.
iChanges may result in significant impair-
ments to the transmission quality. These set-
tings may not be changed during an active phone
call.

241 Controls in detail
Driving systems
Driving systems
The driving systems of your vehicle are de-
scribed on the following pages:

Cruise control, with which the vehicle
can maintain a preset speed.

Hill start assist system which helps you
to start off smoothly on a hill.
For information on the ABS, Adaptive
Brake, BAS, EBP, ESP
®, and 4MATIC, see
“Driving safety systems” (
page 59).
Cruise control
The cruise control automatically maintains
the speed you set for your vehicle.
The use of the cruise control is recom-
mended for driving at a constant speed for
extended periods of time.
You can set or resume the cruise control at
any speed over 20 mph (30 km/h).
The cruise control function is operated by
means of the cruise control lever.
Warning!G
The cruise control is a convenience system
designed to assist the driver during vehicle
operation. The driver is and must always
remain responsible for the vehicle’s speed
and for safe brake operation.
Only use the cruise control if the road,
traffic, and weather conditions make it
advisable to travel at a steady speed.

The use of the cruise control can be
dangerous on winding roads or in heavy
traffic because conditions do not allow
safe driving at a steady speed.

The use of the cruise control can be
dangerous on slippery roads. Rapid
changes in tire traction can result in
wheel spin and loss of control.

Deactivate the cruise control when
driving in fog.
The “Resume” function should only be
operated if the driver is fully aware of the
previously set speed and wishes to resume
this particular preset speed.
Warning!G
The cruise control brakes automatically so
that the set speed is not exceeded. The
brake pedal depresses when the cruise con-
trol engages the brakes.
Keep driver’s foot area clear at all times, in-
cluding the area under the brake pedal. Ob-
jects stored in this area may impair pedal
movement which could interfere with the
braking ability of the cruise control system.
Do not place your foot under the brake pedal
– your foot could become caught.
Keep in mind that the cruise control is a con-
venience system designed to assist the driv-
er during vehicle operation. The driver is and
must always remain responsible for the ve-
hicle’s speed and for safe brake operation.

243 Controls in detail
Driving systems
1SegmentsCanceling cruise control
There are several ways to cancel the cruise
control:
Step on the brake pedal.
The cruise control is canceled. The last
speed set is stored for later use.
or
Briefly push the cruise control lever in
direction of arrow3 (
page 242).
The cruise control is canceled. The last
speed set is stored for later use.
iOn uphill grades, the cruise control may not
be able to maintain the set speed. Once the
grade eases, the set speed will be resumed.
On downhill grades, the cruise control maintains
the set speed by braking with the vehicle’s
braking system. In addition, on longer downhill
grades the automatic transmission* will down-
shift automatically.
iVehicles with manual transmission:
If you depress the clutch pedal when shifting into
another gear, the engine speed may increase.

Always drive at sufficient, but not excessive,
engine speed.

Shift gear in a timely manner.

Avoid shifting down more than one gear if at
all possible.
iThe last stored set speed is canceled when
the engine is turned off.
iThe cruise control switches off
automatically and the segments in the multifunc-
tion display go out when

you step on the brake pedal.

you press the parking brake pedal.
The cruise control switches off automatically,
the segments in the multifunction display go out
and an acoustic warning sounds when

the vehicle speed is below 20 mph
(30 km/h).

the ESP® is in operation or switched off with
the ESP® switch (page 63).

Vehicles with manual transmission:
you engage neutral or depress the clutch
pedal for more than 6 seconds during shift-
ing into another gear.

Vehicles with automatic transmission*:
you move the gear selector lever to
positionN while driving.
Observe additional messages in the
multifunction display that may appear.

244 Controls in detail
Driving systems
Setting a higher speed
You can increase the set speed in two
ways.
Adjustment in 1 mph (Canada: 1 km/h)
incrementsBriefly lift the cruise control lever to the
resistance point in direction of
arrow1 (
page 242).
Release the cruise control lever.
The vehicle set speed increases in in-
crements 1 mph (Canada: 1 km/h).
Adjustment in 5 mph
(Canada: 10 km/h) increments
Briefly lift the cruise control lever past
the resistance point in direction of
arrow1 (
page 242).
Release the cruise control lever.
The vehicle set speed increases in in-
crements 5 mph (Canada: 10 km/h).
!Vehicles with automatic transmission*:
Setting the automatic transmission toN while
driving cancels the cruise control. However, the
gear selector lever should not be moved to
positionN while driving except to coast when
the vehicle is in danger of skidding (e.g. on icy
roads).
iDepressing the accelerator pedal does not
deactivate the cruise control. After brief acceler-
ation (e.g. for passing), the cruise control will re-
sume the last speed set.
Warning!G
If you increase the set vehicle speed, keep in
mind that it may take a brief moment until
the vehicle has reached the set speed.
Increase the set vehicle speed to a value
that the prevailing road conditions and legal
speed limits permit. Otherwise, sudden and
unexpected acceleration of the vehicle
could cause an accident and/or serious
injury to you and others.
iThe set speed value is increased in 1 mph
(Canada: 1 km/h) increments each time you lift
the cruise control lever up to the resistance
point.
iThe set speed value is increased in 5 mph
(Canada: 10 km/h) increments each time you lift
the cruise control lever up past the resistance
point.
iThe new speed is set and the vehicle will ac-
celerate. Keep in mind that it may take a brief
moment until the vehicle has reached the set
speed.

245 Controls in detail
Driving systems
Setting a lower speed
You can reduce the set speed in two ways.Adjustment in 1 mph (Canada: 1 km/h)
increments
Briefly press the cruise control lever
down to the resistance point in direc-
tion of arrow2 (
page 242).
Release the cruise control lever.
The vehicle set speed decreases in in-
crements 1 mph (Canada: 1 km/h).
Adjustment in 5 mph
(Canada: 10 km/h) increments
Briefly press the cruise control lever
down past the resistance point in
direction of arrow2 (
page 242).
Release the cruise control lever.
The vehicle set speed decreases in in-
crements 5 mph (Canada: 10 km/h).
Setting to last stored speed
(“Resume” function)
Warning!G
If you decrease the set vehicle speed, keep
in mind that it may take a brief moment until
the vehicle has the vehicle has reached the
set speed.
Decelerate the set vehicle speed to a value
that the prevailing road conditions and legal
speed limits permit. Otherwise, sudden and
unexpected deceleration of the vehicle
could cause an accident and/or serious in-
jury to you and others.
iWhen you use the cruise control lever to de-
celerate, the brake system will automatically
brake the vehicle if the engine’s braking power
does not brake the vehicle sufficiently.
iThe set speed value is decreased in 1 mph
(Canada: 1 km/h) increments each time you
press the cruise control lever down to the resis-
tance point.
iThe set speed value is decreased in 5 mph
(Canada: 10 km/h) increments each time you
press the cruise control lever down past the re-
sistance point.
iThe new speed is set and the vehicle will de-
celerate. Keep in mind that it may take a brief
moment until the vehicle has reached the set
speed.
Warning!G
The set speed stored in memory should only
be set again if prevailing road conditions
permit. Possible acceleration or decelera-
tion differences arising from returning to the
preset speed could cause an accident
and/or serious injury to you and others.