306 Controls in detail
Useful features
If you live in Canada or if you are having
difficulties programming a gate operator
(regardless of where you live) by using the
programming procedures, replace step 4
with the following:
Step 4:
Press and hold the signal transmitter
button (2, 3 or4). Do not release
this button until it has been successful-
ly trained.
While still holding down the signal
transmitter button (2, 3 or4),
“cycle” your hand-held remote control
button6 as follows: Press and hold
button6 for 2 seconds, then release
it for 2 seconds, and again press and
hold it for 2 seconds. Repeat this se-
quence on the hand-held remote con-
trol until the frequency signal has been
learned. Upon successful training, indi-
cator lamp1 will flash slowly and then
rapidly after several seconds.
Proceed with programming step 5 and
step 6 to complete.Reprogramming a single signal trans-
mitter button
To program a device using a signal trans-
mitter button previously trained, follow
these steps:
Switch on the ignition (page 82).
Press and hold the desired signal
transmitter button (2, 3 or4).
Do not release the button.
Indicator lamp1 will begin to flash af-
ter 20 seconds. Without releasing the
signal transmitter button, proceed with
programming starting with step 3.Operation of integrated remote control
Switch on the ignition (page 82).
Select and press the appropriate inte-
grated signal transmitter button (2,
3 or4) to activate the remote con-
trolled device.
The integrated remote control trans-
mitter continues to send the signal as
long as the button is pressed – up to
20 seconds.
Erasing integrated remote control
memory
Switch on the ignition (page 82).
Simultaneously press and hold outer
signal transmitter buttons2 and 4,
for approximately 20 seconds, until
indicator lamp1 flashes rapidly. Do
not hold for longer than 30 seconds.
The codes of all three channels are
erased.
iUpon completion of programming the inte-
grated remote control, make sure you retain the
hand-held remote control that came with the ga-
rage door opener, gate operator or other device.
You may need it for use in other vehicles, for fu-
ture programming of an integrated remote con-
trol, or simply for continued use as a hand-held
remote control to operate the respective device
in other situations.
iIf you sell your vehicle, erase the codes of all
three channels.
503 Index
SRS 47
Indicator lamp 27, 382
Messages in display 416
Standing lamps 434, 436
Replacing bulbs 431
Standing water, Driving through 318
Starter switch 82
Positions 82
Starting difficulties, Engine 129
Starting, Engine 126
Steering wheel 93, 94
Adjustment, electrical 94
Adjustment, manual 93
Buttons 28
Cleaning 371
Easy entry/exit feature*
(Canada only) 95
Power steering fluid 478
Stolen Vehicle Recovery services 302
Storage compartments 283
Cup holder 287
Front armrest 284
Parcel net 285
Rear armrest 286
Storage compartment in front
armrest 284Storage pockets 286
Storing tires 333
Submenus see Control system submenus
Summer opening feature 123
Sun visors 289
Sunroof see Power tilt/sliding sunroof
Sunshade
Extending/retracting rear window
sunshade 290
Switching
Fuel (Flexible fuel vehicle) 483
Symbols used in this operator’s
manual 14
System settings
Bluetooth
® (Audio system) 192
Display (Audio system) 192
Setting the system language 193
System settings (Audio system)
Menu overview 192
Reset to factory settings 193
Setting the system language 193T
Tachometer 149
Overspeed range 149
Tail lamps
Cleaning lenses 367
Replacing bulbs 431, 436
Tar stains 365
Technical data
Flexible fuel vehicles 482
Tele Aid* 295
Automatic Maintenance Call 302
Call priority 301
Emergency calls 296
Hands-free microphone 31
Information 300
Information button* 300
Initiating an emergency call
manually 298
Messages in display 418
Remote door lock 302
Remote door unlock* 301
Roadside Assistance button* 299,
300
Roadside Assistance* 299
SOS button 298
Stolen Vehicle Recovery
