2008 MAZDA MODEL 6 battery

Black plate (20,1)
CAUTION
ØThe seat-bottom power
adjustment is operated by motors.
Avoid extended operation because
excessive use can damage the
motors.
Ø To prevent the battery from
running down, avoid using the
power adjustment when the
engine is stopped. The adjuster
uses a large amount of electrical
power.
Ø Don't use the switch to make more
than one adjustment at a time.
qSeat Slide (Driver's Seat)
To slide the seat, move the slide lifter
switch on the outside of the seat to the
front or back and hold it. Release the
switch at the desired position.
qSeat Recline (Driver's Seat)
WARNING
Do not drive with the seats reclined:
Sitting in a reclined position while the
vehicle is moving is dangerous
because you don't get the full
protection from seat belts. During
sudden braking or a collision, you
can slide under the lap belt and
suffer serious internal injuries. For
maximum protection, sit well back
and upright.
Always sit in a front passenger seat
properly with the seatback upright and
feet on the floor: If your vehicle is equipped with front
passenger seat weight sensors,
sitting in the front passenger seat
improperly out of position or with the
seatback reclined too far while the
vehicle is moving is dangerous as it
can take off weight from the seat
bottom and affect the weight
determination of the front passenger
sensing system. As a result the front
passenger will not have the
supplementary protection of the air
bag and seat belt pretensioner, which
could cause result in serious injury.
Always sit upright against your
seatback, with your feet on the floor.
2-6
Essential Safety Equipment
Seats
Mazda6_8X47-EA-07G_Edition1 Page20
Tuesday, May 29 2007 3:42 PM
Form No.8X47-EA-07G

Black plate (79,1)
Keyless Entry System
This system remotely locks and unlocks
the doors and the hatch/liftgate, and opens
the trunk lid, and opens the power
windows.
It can also help you signal for attention.
Press the buttons slowly and carefully.
CAUTION
To avoid damage to the transmitter,
do not:
ØDrop the transmitter.
Ø Get the transmitter wet.
Ø Disassemble the transmitter.
Ø Expose the transmitter to any kind
of magnetic field.
Ø Expose the transmitter to high
temperatures on places such as
the dashboard or hood, under
direct sunlight. NOTE
lThe keyless entry system is designed to
operate up to about 2.5 m (8 ft) from the
center of the vehicle, but this may vary due
to local conditions.
lThe system doesn't operate when the key is
in the ignition switch.
lDoors and the hatch/liftgate can be locked
by pressing the lock button while any other
door or the hatch/liftgate/trunk lid is open.
However, the hazard warning lights will not
flash.
lIf the transmitter does not operate when
pressing a button or the operation range
becomes too small, the battery may be
dead. To install a new battery, refer to
Maintenance (page 3-5).
lAdditional transmitters can be obtained at
an Authorized Mazda Dealer. Up to 3
transmitters can be used with the keyless
entry system per vehicle. Bring all
transmitters to an Authorized Mazda
Dealer when additional transmitters are
required.
q
Transmitter
Sedan
Lock button
Unlock button
Trunk button Panic button
Operation
indicator light
Knowing Your Mazda
Doors and Locks
3-3
Mazda6_8X47-EA-07G_Edition1 Page79
Tuesday, May 29 2007 3:43 PM
Form No.8X47-EA-07G

Black plate (81,1)
NOTE(Without theft-deterrent system)
The hazard warning lights will flash twice to
indicate that all doors and the hatch/liftgate
are unlocked.
(With theft-deterrent system)
lThe hazard warning lights will not flash.lThe hazard warning lights only flash when
the theft deterrent system is armed or
turned off, refer to the theft-deterrent
system (page 3-35).
NOTEAuto re-lock function
After unlocking with the transmitter, all doors
and the hatch/liftgate will automatically lock if
one of the doors or the hatch/liftgate/trunk lid
is not opened within about 30 seconds.
Trunk button
To open the trunk, press and hold the
trunk button until the trunk lid opens.
Panic button
If you witness from a distance someone
attempting to break into or damage your
vehicle, pressing the panic button will
activate the vehicle's alarm.
NOTE
The panic button will work whether any door
or the trunk lid is open or closed.
Turning on the alarm
Pressing the panic button for 1 second or
more will trigger the alarm for about 2
minutes and 30 seconds, and the
following will occur:
lThe horn sounds intermittently.lThe hazard warning lights flash.
Turning off the alarm
Press any button on the transmitter.
q Transmitter Maintenance
If the buttons on the transmitter are
inoperable and the operation indicator
light does not flash, the battery may be
dead.
Replace with a new battery before the
transmitter becomes unusable.
CAUTION
Ø Install the battery with the positive
pole () facing down. Battery
leakage could occur if it is not
installed correctly.
Ø When replacing the battery, be
careful not to bend the electrical
terminals or get oil on them. Also
be careful not to get dirt in the
transmitter as it could be
damaged.
Ø There is the danger of explosion if
the battery is not correctly
replaced.
Ø Replace only with the same type
battery (CR1620 or equivalent).
Ø Dispose of used batteries
according to the following
instructions.
ØInsulate the plus and minus
terminals of the battery using
cellophane or equivalent tape.
ØNever disassemble.ØNever throw the battery into
fire and/or water.
ØNever deform or crush.
Replacing the transmitter battery
1. Unfold the key (page 3-2).
Knowing Your Mazda
Doors and Locks
3-5
Mazda6_8X47-EA-07G_Edition1 Page81
Tuesday, May 29 2007 3:43 PM
Form No.8X47-EA-07G

Black plate (82,1)
2. Insert a small screwdriver into the slotand push the tab to remove the key
from the transmitter.
Ta b
3. Insert a small screwdriver into the slotand gently pry open the transmitter.
4. Press the portion of the batteryindicated by A and remove the battery.
A
NOTEIf it is difficult to remove the battery by
pressing with a finger, use a small screwdriver
to press out the battery.
5. Put in the new battery (CR1620 orequivalent) with the positive pole ()
facing down.
6. Align the front and back covers and snap the transmitter shut.
7. Install the key to the transmitter.
q Service
If you have a problem with the keyless
entry system, consult an Authorized
Mazda Dealer.
If your transmitter is lost or stolen, bring
all remaining transmitters to an
Authorized Mazda Dealer as soon as
possible for a replacement and to make
the lost or stolen transmitter inoperative.
3-6
Knowing Your Mazda
Doors and Locks
Mazda6_8X47-EA-07G_Edition1 Page82
Tuesday, May 29 2007 3:43 PM
Form No.8X47-EA-07G

Black plate (87,1)
qOpening and Closing the Hatch
To open the hatch, pull up on the handle.
NOTEIf the vehicle battery is dead or there is a
malfunction in the electrical system and the
hatch cannot be unlocked, perform the
following manual procedure as an emergency
measure to unlock it:
1. Remove the cap on the interior surface of
the hatch with a flathead screwdriver.
Cap
2. Turn the lever to the right to unlock thehatch.
Lever
After performing this emergency measure,
have the vehicle inspected at an Authorized
Mazda Dealer as soon as possible.
To close, use both hands to push the hatch
down until the lock snaps shut. Do not
slam it. Pull up on the hatch to make sure
it is secure.
Knowing Your Mazda
Doors and Locks
3-11
Mazda6_8X47-EA-07G_Edition1 Page87
Tuesday, May 29 2007 3:43 PM
Form No.8X47-EA-07G

Black plate (90,1)
NOTEIf the vehicle battery is dead or there is a
malfunction in the electrical system and the
liftgate cannot be unlocked, perform the
following procedure as an emergency measure
to unlock it:
1. Remove the cap on the interior surface ofthe liftgate with a flathead screwdriver.
Cap
2. Turn the lever to the right to unlock theliftgate.
Lever
After performing this emergency measure,
have the vehicle inspected at an Authorized
Mazda Dealer as soon as possible.
Closing the liftgate
Use both hands to push the liftgate down
until the lock snaps shut. Do not slam it.
Pull up on the liftgate to make sure it is
securely latched.
qLuggage Compartment Cover
Use the luggage compartment cover to
conceal cargo or luggage.
WARNING
Do not place anything on top of the
luggage compartment cover:
Placing luggage or other cargo on
top of the luggage compartment
cover is dangerous. During sudden
braking or a collision, the cargo
could become a projectile that could
hit and injure someone.
CAUTION
Make sure the luggage compartment
cover is firmly secured. If it is not
firmly secured, it could unexpectedly
disengage resulting in injury.
Installing the cover
1. Set the left end of the retainer bar intothe notch on the left side of the luggage
compartment.
Retainer bar
Notch
3-14
Knowing Your Mazda
Doors and Locks
Mazda6_8X47-EA-07G_Edition1 Page90
Tuesday, May 29 2007 3:43 PM
Form No.8X47-EA-07G

Black plate (96,1)
Opening the trunk lid with the key
Insert the key into the slot and turn it
clockwise.
Open
Opening the trunk lid with thetransmitter
The trunk lid can be opened by operating
the keyless entry system transmitter, refer
to Keyless Entry System (page 3-3).
Opening the trunk lid with the remoterelease button
Push the release button.
Closing the trunk lid
Use both hands to push the trunk lid down
until the lock snaps shut. Do not slam it.
Pull up on the trunk lid to make sure it is
secure.
qTrunk Light
The trunk light is on when the lid is open
and off when it's closed.
NOTETo prevent the battery from being discharged,
do not leave the trunk open for a long period
when the engine is not running.
3-20
Knowing Your Mazda
Doors and Locks
Mazda6_8X47-EA-07G_Edition1 Page96
Tuesday, May 29 2007 3:43 PM
Form No.8X47-EA-07G

Black plate (100,1)
NOTE(POWER WINDOW INITIALIZATION
PROCEDURE)
If the battery was disconnected during vehicle
maintenance, or for other reasons such as a
switch continues to be operated after the
window is fully open/close, the power windows
will not fully open and close automatically. Re-
initialization of the automatic function can be
performed using the master control switches
and the front passenger door switch. Carry out
the following procedure to resume operation:
1. Turn the ignition switch to the ON position.
2. Make sure that the power window lockswitch located on the driver's door is not
depressed.
3. Press the switch and fully open the power window.
4. Pull up the switch to fully close the power window and continue holding the switch for
about 2 seconds after the window fully
closed.
5. Repeat Steps 3-4 for each front power window.
6. Make sure that the power windows operate correctly using the door switches.
Two-step down function
With the power window completely
closed, press the switch lightly and it will
open and stop about 3 cm (1 in) from the
top.
If you continue to press and hold the
switch, the window will resume opening
all the way.
NOTE
Pressing the power window switch once when
the window is fully closed will only open it
about 3 cm (1 in) to allow convenient
ventilation of the cabin.
Canceling the two-step down function
To cancel the two-step down function for
the front power windows, carry out the
following procedure using the master
control switches.
1. Turn the ignition switch to the ONposition and complete the following
procedure within 5 seconds:
Press the power window switch 2 times
firmly, then pull it 2 times firmly.
Master control switches
Driver's
window
Front passenger's
window
2. Turn the ignition switch to the LOCKposition.
3. With the ignition switch in the LOCK position, and within 40 seconds, turn
the ignition switch to the ON position
and complete the following procedure
within 5 seconds:
Press the power window switch 2 times
firmly, then pull 2 times firmly.
3-24
Knowing Your Mazda
Doors and Locks
Mazda6_8X47-EA-07G_Edition1 Page100
Tuesday, May 29 2007 3:43 PM
Form No.8X47-EA-07G