2008 LEXUS RX400H tow

380
5-1. Essential information
RX400h_U
Installing towing eyeletsRemove the eyelet cover.
Insert the towing eyelet into the
hole and tighten partially by hand.
Tighten down the towing eyelet
securely using a wheel nut wrench.
STEP1
STEP2
STEP3
■Location of the emergency towing eyelet
→P. 4 0 8

5
When trouble arises
381
5-1. Essential information
RX400h_U
Towing with a sling-type truck
CAUTION
■Installing towing eyelets to the vehicle
Make sure that towing eyelets are installed securely.
If not securely installed, towing eyelets may come loose during towing. This may
lead to accidents that cause serious injury or even death.
NOTICE
■To prevent body damage
Do not tow with a sling type truck, either from the front or rear.

382
5-1. Essential information
RX400h_U
Towing with a wheel lift-type truckFrom the front (2WD models) Release the parking brake.
From the front (AWD models) Use a towing dolly under the rear
wheel.
NOTICE
■To prevent damaging the vehicle
When raising the vehicle, ensure adequate ground clearance for towing at the
opposite end of the raised vehicle.
Without adequate clearance, the vehicle could be damaged while being towed.
■To prevent causing serious damage to the transmission (AWD models)
Never tow this vehicle from the front with the rear wheels on the ground.

5
When trouble arises
383
5-1. Essential information
RX400h_UFrom rear
Use a towing dolly under the front
wheels.
Using a flat bed truck
If your Lexus is transported by a
flat bed truck, it should be tied
down at the locations shown in the
illustration.
If you use chains or cables to tie
down your vehicle, the angles
shaded in black must be 45°.
Do not overly tighten the tie downs
or the vehicle may be damaged.
NOTICE
■To prevent causing serious damage to the transmission
Never tow this vehicle from the rear with the front wheels on the ground.
FrontFront

384
5-1. Essential information
RX400h_U
NOTICE
■To avoid serious damage to your vehicle
Do not use the rear emergency towing eye-
lets.

408
5-2. Steps to take in an emergency
RX400h_U
If you have a flat tire
Remove the flat tire and replace it with the spare provided.
■Before jacking up the vehicle
● Stop the vehicle on a hard, flat surface.
● Set the parking brake.
● Shift the shift lever to P.
● Stop the hybrid system.
● Turn on the emergency flashers.
■ Location of the spare tire, jack and tools
Jack
Adapter socket Wr e n c h
Towing eyelet
Jack handle
Tool bag
Spare tire

5
When trouble arises
415
5-2. Steps to take in an emergency
RX400h_U
Stowing the flat tire, jack and all toolsInstall the inside spare tire cover on the outer side of the spare tire
cover. Put the flat tire in the spare tire
cover with the outer side facing up
and install the holding bracket.
Turn the spare tire clamp bolt clockwise with a jack handle and
adapter socket until you hear a click.
Stow all the tools and jack securely.
STEP1
STEP2
■After completing the tire change
The tire pressure warning system must be reset. ( →P. 3 3 2 )
STEP3
STEP4

5
When trouble arises
417
5-2. Steps to take in an emergency
RX400h_U
NOTICE
■Do not drive the vehicle with a flat tire.
Do not continue driving with a flat tire.
Driving even a short distance with a flat tire can damage the tire and the wheel
beyond repair.
■When replacing the tires
When removing or fitting the wheels, tires or the tire pressure warning valve and
transmitter, contact your Lexus dealer as the tire pressure warning valve and trans-
mitter may be damaged if not handled correctly.
■To avoid damaging the tire pressure warning valves and transmitters
Do not use liquid sealants on flat tires.
■When stowing the flat tire
●Ensure that there is no object caught between the tire and the vehicle underbody.
●Tighten the spare tire clamp bolt to hold the spare wheel carrier by the hook
securely.