2008 Lexus IS F check engine

Finish
BASIC FUNCTIONS
22
When the “ENGINE START STOP” switch
is in ACCESSORY or IGNITION ON
mode, the initial screen will be displayed
and the system will begin operating.
CAUTION
When the vehicle is stopped with the
engine running, always apply the
parking brake for safety.
After a few seconds, the “CAUTION”
screen will be displayed.
After about 5 seconds, the “CAUTION”
screen automatically switches to the map
screen. When the“MAP/VOICE”button
is also pushed, the map screen is dis-
played.
While the “CAUTION” screen is displayed,
the “DEST” or“MENU” button cannot be
operated. And if the “Language”,“Cal-
endar” or“Maintenance” buttons on the
“Information” screen are touched, the
screen will change back to “CAUTION”
screen and then change to the map screen
in about 5 seconds later or if the “MAP/
VOICE” button is pushed.
DMaintenance information
This system informs about when to replace
certain parts or components and shows
dealer information (if registered) on the
screen.
When the vehicle reaches a previously set
driving distance or date specified for a
scheduled maintenance check, the “Infor-
mation” screen will be displayed when the
navigation system is in operation.
To disable this screen, touch “Do Not
Display This Message Again.”. This
screen goes off if the screen is not op-
erated for several seconds.
To prevent this information screen from be-
ing displayed again, touch “Do Not
Display This Message Again.” .
To register “Maintenance information”, see
“Maintenance information” on page 118.
IS F/350/250_Navi_U
(L/O 0712)
Initial screen

Finish
OTHER FUNCTIONS
11 9
INFORMATION ITEMS
“ENGINE OIL”:Replace engine oil
“OIL FILTER”: Replace engine oil filter
“ROTATION”: Rotate tires
“TIRES”: Replace tires
“BATTERY”: Replace battery
“BRAKE PAD”: Replace brake linings
“WIPERS”: Replace wiper blades
“LLC”: Replace engine coolant
“BRAKE OIL”: Replace brake fluid
“ATF”: Replace ATF (Automatic Trans-
mission Fluid)
“SERVICE”: Scheduled maintenance
“AIR FILTER”: Replace air filter
“PERSONAL”: New information items
can be created separately from provided
ones.
4. Input the conditions.
Notice of “Date”: The next maintenance
date can be input.
Notice of “Distance”: The driving dis-
tance until the next maintenance check
can be input.
“Delete”: To cancel the date and distance
conditions.
“Reset”: To reset the date and distance
conditions .
5. Touch “OK”.
The screen then returns to the “Mainte-
nance” screen.
INFORMATION
D For scheduled maintenance infor-
mation, please refer to the “Own-
er’s Manual Supplement/Sched-
uled Maintenance”.
D Depending on driving or road con-
ditions, the actual date and dis-
tance may differ from the stored
date and distance in the system.
IS F/350/250_Navi_U
(L/O 0712)

Finish
OTHER FUNCTIONS
152
D
The Bluetooth
rconnection status at
startup
When the “ENGINE START STOP”
switch is in ACCESSORY or IGNITION
ON mode and the Bluetooth ris auto-
matically connected, the connection
check is displayed.
Touch “ON” or “OFF” of “Show
Bluetooth
connection status at start-
up”.

: Bluetooth is a registered trademark of Bluetooth SIG. Inc.
DInitializing the settings
You can initialize the settings.
Touch “Default”.
Touch “Yes”.
IS F/350/250_Navi_U
(L/O 0712)

Finish
AUDIO/VIDEO SYSTEM
219
(f) If the player malfunctions
If the player or another unit equipped with
the player malfunctions, your audio sys-
tem will display following messages.
If “No CD” appears on the display:It in-
dicates that there is no disc in the CD
changer.
If “CD ××Check” appears on the dis-
play: It indicates that the disc dirty, dam-
aged, or it was inserted upside down.
Clean the disc or insert it correctly. If a disc
which is not playable is inserted, “CD ××
Check” will also appear on the screen. For
appropriate discs for this player, see “Au-
dio/video system operating hints” on page
241.
If “CD Error” appears on the display:
The following causes are possible.
DThere is a trouble inside the system.
Eject the disc.
DThe inside of the player unit may be too
hot due to the very high ambient tem-
perature. Eject the disc and allow the
player to cool down.
If “NO MUSIC FILE” appears on the dis-
play: It indicates that the disc has no play-
able data.
If the malfunction is not rectified: Take
your vehicle to your dealer.
If an MP3/WMA disc contains CD− DA
files, only CD −DA files are played. If an
MP3/WMA disc contains files other than
CD− DA, only MP3/WMA files are played. The DVD changer can play audio CDs,
video CDs, CD text, WMA discs, MP3
discs, DVD video discs and DVD audio
discs.
DAudio CD, CD text
211
.........
DMP3/WMA disc 214
...........
DDVD video, DVD audio 224 .....
DVideo CD 236
.................
For appropriate discs for this changer, see
“Audio/video system operating hints” on
page 241.
For safety reasons, you can enjoy DVD
video discs, DVD audio discs and video
CDs only when the vehicle is completely
stopped with the “ENGINE START STOP”
switch is in ACCESSORY or IGNITION
ON mode and the parking brake applied.
While you are driving, you can hear audio
alone even in the DVD video, DVD audio
or video CD mode.
IS F/350/250_Navi_U
(L/O 0712)
— DVD changer operation

Finish
AUDIO/VIDEO SYSTEM
220
(a) Inserting or ejecting discs
The “ENGINE START STOP” switch must
be in ACCESSORY or IGNITION ON
mode.
Your DVD changer can store up to 6 discs.
DSetting a single disc:
1. Push the “LOAD” button briefly.
The orange indicators at both ends of the
slot start blinking. After the orange indica-
tors change to green and stay on, the DVD
changer door will open.
2. Insert only one disc while the DVD
changer door is open.
You can set a disc at the lowest empty disc
number.
After insertion, the set disc is automatically
loaded.
If the label faces down, the disc cannot be
played. In this case, “DISC×Check” ap-
pears on the screen.
If you do not insert the disc within 15 sec-
onds after pushing the “LOAD”button, the
beep will sound and the operation will be
canceled automatically.
If you need to insert the next disc, repeat
the same procedure to insert another disc.
IS F/350/250_Navi_U
(L/O 0712)

Finish
AIR CONDITIONING
266
(g) Adjusting the position of and open-
ing and closing the air outlets
"Center outlets
1Adjusting air flow direction
2Open or close the vent
"Side outlets
1Adjusting air flow direction
2Open or close the vent
"Rear seat outlets
1Adjusting air flow direction
2Adjusting air flow direction or,
open or close the vent
If air flow control is not satisfactory,
check the center vents, side vents and
rear vents. They may be opened or
closed as shown.
When outside temperature is cold like a
winter season, air flow temperature from
the center vents, side vents and rear vents
may not be warmed up enough for a while
until that the engine coolant temperature
becomes high enough.
If air flow from the center vents, side vents
and rear vents is not satisfactory, air flow
direction can be changed manually by ad-
justing the vents fin direction or the vents
may be closed.
IS F/350/250_Navi_U
(L/O 0712)

Finish
REAR VIEW MONITOR SYSTEM
272
The rear view monitor system assists
the driver by displaying an image of the
view behind the vehicle while backing
up. The image is displayed in reverse
on the screen. This allows the image to
appear in the same manner as that of
the rear view mirror.
To display the rear view image on the
screen, shift the shift lever to “R” (auto-
matic transmission) or reverse (manual
transmission) when the “ENGINE
START STOP” switch is in IGNITION ON
mode.
If you move the shift lever out of the “R”
(automatic transmission) or reverse
(manual transmission), the screen returns
to the previous screen. Operating another
function of the navigation system will dis-
play another screen.
Vehicles with Lexus parking assist−sen-
sor — when the Lexus parking assist −
sensors are turned on and an obstacle is
detected in front of or behind your ve-
hicle, a warning appears on the right top
of the rear view monitor. For details, see
“Lexus parking assist −sensor” on page
278.
The rear view monitor system is a supple-
ment device intended to assist back up.
When backing up, be sure to check behind
and all around the vehicle visually.
CAUTION
DNever depend on the rear view
monitor system entirely when
backing up. Always make sure
your intended path is clear.
Use caution, just as you would
when backing up any vehicle.
DNever back up while looking only at
the screen. The image on the
screen is different from actual
conditions. Depicted distances
between objects and flat surfaces
will differ from actual distance. If
you back up while looking only at
the screen, you may hit a vehicle, a
person or an object. When backing
up, be sure to check behind and all
around the vehicle visually and
with mirrors before proceeding.
DDo not use the system when the
trunk is not completely closed.
DIf the back of the vehicle is hit, the
position and mounting angle of the
camera may change. Be sure to
have the camera’s position and
mounting angle checked at your
Lexus dealer.
DAs the camera has a water proof
construction, do not detach, disas-
semble or modify it. This may
cause incorrect operation.
DIf the temperature changes rapidly,
such as when hot water is poured
on the vehicle in cold weather, the
system may not operate normally.
IS F/350/250_Navi_U
(L/O 0712)
Rear view monitor system
—

Finish
LEXUS PARKING ASSIST−SENSOR
278
The Lexus parking assist−sensor is a
warning system used when parking the
vehicle at low speed (e.g. into a garage).
It uses an ultrasonic sensor, which
checks the approximate distance to an
obstacle. It will inform you of the
approximate distance to an obstacle by
displaying information on the multi −in-
formation display and the screen, and
with beeping sounds.
1Front corner sensors
There is one of these installed on each cor-
ner of the front bumper, they inspect ob-
stacles and will sound a warning depend-
ing on the distance to the obstacle. (See
“ — Front corner sensors” on page 280.)
2Rear corner sensors
There is one of these installed on each cor-
ner of the rear bumper, they inspect ob-
stacles and will sound a warning depend-
ing on the distance to the obstacle. (See
“ — Rear corner sensors” on page 281.)
3Back sensors
There are two of these installed near the
center of the rear bumper, they inspect ob-
stacles and will sound a warning depend-
ing on the distance to the obstacle. (See
“ — Back sensors” on page 282.)
To use the parking assist −sensor, with
the “ENGINE START STOP” switch in
IGNITION ON mode, push “
”or“”
of the satellite switch to select the park-
ing assist− sensor and then push the
ON/OFF button. Selecting the parking
assist− sensor and pushing the ON/OFF
button of the satellite switch again will
turn the parking assist −sensor off.
When you turn on the parking assist −sen-
sor, the indicator light in the instrument
cluster comes on and a beep sounds for
one second, indicating that the parking as-
sist− sensor is turned on.
The parking assist −sensor will remain on
even after turning the “ENGINE START
STOP” switch to OFF and then to IGNI-
TION ON mode with the main switch on.
However, a beep does not sound at this
time.
If an error is detected in the Lexus parking
assist− sensor while self −checking, beeps
sound and a warning appears in the multi −
information display and on the screen. For
details, see “ — Lexus parking assist −sen-
sor failure warning” on page 285.
IS F/350/250_Navi_U
(L/O 0712)
Lexus parking
assist− sensor —