2008 Lancia Musa window

51
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
DEMISTING/DEFROSTING
OF REAR WINDOW DEMISTER
AND ELECTRICAL DOOR
MIRRORS (where provided)
Press button C-fig. 61to enable this
function. When the function is active,
a led on the button goes on.
This is a timed function, which is au-
tomatically disabled by the system af-
ter a preset time. Press button C
again to disable the function in ad-
vance.
IMPORTANT Do not affix decals on
the inside of the rear window over the
heating filaments to avoid damage
that might cause it to stop working
properly.Regulating cooling
Proceed as follows:
❒stop internal air recirculation by
placing knob F-fig. 61on
Ú;
❒turn the rotating knurled ring B
clockwise to increase the temper-
ature;
❒turn knob Aanticlockwise to re-
duce the fan speed.
SERVICING THE SYSTEM
Run the climate control system for at
least 10 minutes every month during
the winter. Have the system inspected
at a Lancia Dealership before the
summer. CLIMATE CONTROL
(cooling and de-humidification)
Proceed as follows:
❒position the rotating knurled ring
B-fig. 61on the blue section to
select the required temperature;
❒turn knob Ato the required speed;
❒position the knurled ring Eon
«;
❒position the knob Fon
…;
❒press button D
√(the LED on the
button goes on).
038-094 MUSA 3ed GB 12-11-2007 11:35 Pagina 51

52
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
The temperature of the delivered air
is always controlled automatically de-
pending on the temperature values set
on the driver’s and front passenger’s
display (except for cases in which the
system is OFF or the compressor dis-
engaged).
The following parameters and func-
tions can be set or changed manually:
❒temperature of air on driver’s/
front passenger’s side;
❒fan speed (continuous variation);
❒air distribution on five levels (dri-
ver’s/front passenger’s side);
❒climate control compressor ON;
❒monozone/two-zone distribution
priority;
❒fast demisting/defrosting;
❒air recirculation;
❒rear window demister;
❒system deactivation. ❒compressor ON (for air
cooling/de-humidification);
❒air recirculation.
All functions may be manually
changed. In order words, you may se-
lect one or more functions and change
the parameters as required. Auto-
matic control of the manually
changed functions will be suspended:
the system will change override your
settings only for safety-related reasons
(e.g. risk of misting up).
Manual selections always have higher
priority over automatic settings and
are stored until the user switches the
system back to automatic control ex-
pect for cases in which the system in-
tervenes for particular safety-related
reasons.
You can adjust one function automat-
ically and have the automatic system
control all the others.
The amount of air delivered to the
passenger compartment depends on
the car speed, because it is regulated
by the electronic fan.AUTOMATIC
TWO-ZONE
CLIMATE
CONTROL SYSTEM
(where provided)
INTRODUCTION
The automatic two-zone climate con-
trol system adjusts the temperature
and distribution of air in the passen-
ger compartment in two zones: the
driver’s side and the passenger’s side.
Temperature is controlled on the ba-
sis of an “equivalent temperature”
principle. In other words, the system
continuously works to keep the com-
fort level inside the car constant and
to compensate for possible variations
of external conditions, including sun
radiation detected by a specific sen-
sor.
The automatically controlled para-
meters and functions are:
❒air temperature delivered to dri-
ver/front passenger vents;
❒air distribution to driver/front pas-
senger vents;
❒fan speed (continuous air flow
variation);
038-094 MUSA 3ed GB 12-11-2007 11:35 Pagina 52

53
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
CONTROLS
A:button for activating the MONO
function (alignment of set temper-
atures);
B:climate control compressor on/off
button;
C:air recirculation on/off button;
D:climate control system information
display;
L:fan speed increase/decrease;
M:air distribution button on driver’s
side;
N:button for activating the AUTO
function (automatic operation)
and knob for setting the tempera-
ture on the driver’s side. E:climate control system off button;
F:button for activating the MAX-
DEFfunction (fast front window
defrosting/demisting);
G:rear window demister on/off but-
ton;
H:button for activating the AUTO
function (automatic operation)
and knob for setting the tempera-
ture on the passenger’s side;
I:air distribution button on passen-
ger’s side;
fig. 62L0D0065m
038-094 MUSA 3ed GB 12-11-2007 11:35 Pagina 53

54
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
During fully automatic operation the
set temperatures, the air distribution
and fan speed can be changed using
the corresponding supplied buttons or
knobs at any time. The system will
automatically change the settings to
adapt to the new request.
During fully automatic operation
(FULL AUTO), the word FULLwill
disappear if the air distribution, air
speed, compressor and/or recircula-
tion settings are changed. In this way,
the functions will switch from auto-
matic to manual control until AUTO
is pressed again. There is only one fan
speed in all the areas of the passenger
compartment.
With on or more manually set func-
tions, the delivered air temperature is
still managed automatically by the
system, except for when the compres-
sor is off. In the case, the air delivered
into the passenger compartment can-
not be cooler than the outside air. During fully automatic operation, the
only functions that are enabled man-
ually are:
❒MONOto align the air tempera-
ture and distribution on the pas-
senger’s side with that on the dri-
ver’s side;
❒
…, air recirculation, to keep it
always on or off;
❒
-to speed up demisting/defrost-
ing of windscreen, side windows,
rear window and door mirrors;
❒
(to demist/defrost the rear win-
dow and door mirrors. USING THE CLIMATE
CONTROL SYSTEM
The system can be started in different
ways, but it is advisable to press one
of the AUTObuttons and then to turn
the knobs to set the temperatures re-
quired on the display.
As the system manages two zones in
the passenger compartment, the driver
and front passenger can select differ-
ent temperature values with a maxi-
mum difference of 7 °C.
The system starts running automati-
cally in this way in order to reach
comfortable temperature as quickly
as possible depending on the set tem-
perature values. The system adjusts
the temperature, amount and distrib-
ution of air delivered to the passenger
compartment. In addition, it manages
the recirculation function to engage
the climate control system compres-
sor.
038-094 MUSA 3ed GB 12-11-2007 11:35 Pagina 54

56
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
˙
▼Air flow distributed between the
foot well vents (hotter air) and the
central and side dashboard vents
(cooler air). This distribution
mode is particularly useful in
spring and autumn on a sunny
day.
▲
▼Air flow distributed between foot
well vents and windscreen and
front side window
defrosting/demisting vents. This
distribution mode enables proper
heating of the passenger compart-
ment, thus preventing possible
window misting. The function is enabled when the pas-
senger compartment needs to be
cooled as quickly as possible, thus us-
ing the system operating capacity at
best. This function enables air recir-
culation and engages the climate con-
trol system compressor; air distribu-
tion and fan speed are managed by
the system based on ambient condi-
tions. All manual settings will be al-
lowed when this function is on.
To switch the function off, simply turn
the temperature knob clockwise and
set the required temperature.Air distribution
buttons I-M
Pressing these but-
tons it is possible to
manually set one of
the five possible air
distribution modes to
the passenger com-
partment (right or
left side):
▲air flow to the windscreen and
front side window vents to demist
or defrost them;
˙air flow at central and side dash-
board vents to ventilate the chest
and the face during the hot season;
▼air flow to the front and rear foot
well vents. Thanks to the natural
upwards movement of heat, this
type of distribution is the quickest
for heating the passenger com-
partment offering the passenger(s)
a prompt feeling of heated air.
038-094 MUSA 3ed GB 12-11-2007 11:35 Pagina 56

59
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IMPORTANT Air recirculation ON
enables faster achievement of the de-
sired conditions (for passenger com-
partment heating or cooling). It is
however inadvisable to use it on
rainy/cold days as it would consider-
ably increase the possibility of the
windows misting inside, especially if
the climate control compressor is off.
Recirculation is forced to off (i.e. air
is introduced from the outside) when
the outside temperature is inferior to
5-7°C to prevent misting up.Climate control
compressor on/off
button B
Press button
√when
the LED on it goes on.
The LED goes off when the climate
control compressor is switched off.
Press the button when the LED is off
to automatically restore system con-
trol and use of the compressor. Suc-
cessful completion of this operation is
highlighted by the button LED
switching on.
The system will switch recirculation
off when the compressor is switched
to off to prevent windows from mist-
ing up. Although the system is capa-
ble of maintaining the required tem-
perature, the word FULLwill disap-
pear from the display. If on the other
hand the system cannot maintain the
required temperature, the digits will
blink and the word AUTOwill disap-
pear.
IMPORTANT With the compressor
off, it is not possible to introduced air
cooler than ambient temperature into
the passenger compartment. Further-
more, in certain conditions, the win-
dows could mist up rapidly because
the air is not dehumidified.
It is advisable not to use
the air recirculation func-
tion when the outside temperature
is low to prevent the windows from
rapidly misting up.
WARNING
038-094 MUSA 3ed GB 12-11-2007 11:35 Pagina 59

60
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IMPORTANT The fast window
demisting/defrosting function remains
engaged for approx. 3 minutes start-
ing from the time when the engine
coolant exceeds 50°C (petrol versions)
or 35°C (Multijet versions).
When this function is active, the LED
of the corresponding button switches
on and that of the rear window
demister. The text FULL AUTOgoes
off on the display.
You can only adjust the fan speed and
switch the rear window demister off
manually when this function is active.
To restore operating conditions before
this function is activated, press but-
tonF, the air recirculation button C,
the compressor button Bor button
AUTO NorH. Fast window
demisting/
defrosting button F
Press this button: the
climate control system
will automatically switch on all the
functions required for fast windscreen
and front side window demisting/de-
frosting, that is:
❒switches on the climate control
compressor when weather condi-
tions are suitable;
❒disables air recirculation;
❒sets the maximum air temperature
HIin both areas;
❒sets proper fan speed according to
engine coolant temperature to
limit the flow of not sufficiently
warm air to demist the windows
into the passenger compartment;
❒directs the air flow to the wind-
screen and front side windows
vents;
❒engages the rear window mister.Disengagement of the compressor re-
mains stored even after the engine
stops.
To restore automatic compressor con-
trol, press button
√again (in this
case, the system will only work as a
heater) or press AUTO.
With climate control compressor off if
the outside temperature is higher than
the one set, the system will not be able
to keep the required condition, the
temperature value will then start
flashing on the display for a few sec-
onds and the message AUTOgoes off.
With climate control compressor off,
the fan speed can be set to zero man-
ually (no bar shown).
With the compressor enabled and the
engine started, the fan speed may be
reduced to the minimum setting only
(one bar shown).
038-094 MUSA 3ed GB 12-11-2007 11:35 Pagina 60

61
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
Switching the
system OFF E
Press button Eto
switch the climate
control system off.
The display will go
out as a consequence.
The following climate control condi-
tions will be established when the sys-
tem is off:
❒LEDs are off;
❒temperatures set are not displayed;
❒air recirculation is enabled, thus
isolating the passenger compart-
ment from external conditions;
❒the climate control compressor is
off;
❒the fan is off.With the system OFF the rear window
demister can either be enabled or dis-
abled manually by pressing button G.
IMPORTANT The system unit stores
the temperatures set before turning
off and resets them when pressing any
button (except heated rear window).
If the function corresponding to the
button pressed is off, it will be turned
on; if on, it will be kept active.
Press button AUTOto switch the the
climate control system on in auto-
matic mode. Demisting/
defrosting button
for rear window
and door mirrors G
Press this button to
activate heated rear window demist-
ing/defrosting. When this function is
on, the button led is on.
This function switches off automati-
cally after a pre-set time or by press-
ing again the button or by turning the
engine off. It will not be switched on
automatically when restarting the en-
gine.
IMPORTANT Do not affix decals on
the inside of the rear window over the
heating filaments to avoid damage
that might cause it to stop working
properly.
038-094 MUSA 3ed GB 12-11-2007 11:35 Pagina 61