2008 INFINITI QX56 battery volt

AV
POWER SUPPLY AND GROUND CIRCUITAV-69
< COMPONENT DIAGNOSIS > [AUDIO SYSTEM]
C
D
E
F
G H
I
J
K L
M B A
O P
3. Check voltage between rear view camera control unit harness connector B73 and ground.
Is voltage reading approximately 6 volts?
YES >> Inspection End.
NO >> Replace rear view camera control unit. Refer to AV-184,
"Removal and Installation".
4.CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect rear view camera harness connector.
3. Check continuity between rear view camera harness connector D504 terminal 2 and ground.
Does continuity exist?
YES >> Inspection End.
NO >> Repair harness or connector.
DVD PLAYER
DVD PLAYER : Diagnosis ProcedureINFOID:0000000001696104
1.CHECK FUSE
Check that the DVD player fuse is not blown.
Is the fuse OK?
YES >> GO TO 2
NO >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse.
2.POWER SUPPLY CIRCUIT CHECK
1. Disconnect DVD player connector M205.
2. Check voltage between the DVD player connector M205 and ground.
Are the voltage results as specified?
YES >> GO TO 3
NO >> • Check connector housings for disconnected or loose terminals. • Repair harness or connector.
Signal name Connector
No. Te r m i n a l
No. Transmission
position Value (Approx.)
Camera ON signal B73 8 Reverse 6V
ALLIA0247ZZ
Signal nameContinuity
Ground Yes
ALLIA0248ZZ
UnitTerminal Signal name Fuse No.
DVD player 21
Battery power 31
24 Ignition switch ACC or ON 4
(+)
(-) OFF ACC ON
Connector Terminal
M205 21
Ground Batter
voltage Battery
voltage Battery
voltage
24 0VBattery
voltage Battery
voltage
ALNIA0325GB
Revision: March 2010 2008 QX56

AV
SUBWOOFERAV-97
< COMPONENT DIAGNOSIS > [AUDIO SYSTEM]
C
D
E
F
G H
I
J
K L
M B A
O P
SUBWOOFER
DescriptionINFOID:0000000001696133
The AV control unit sends audio signals to the BOSE s peaker amp. The BOSE speaker amp. amplifies the
audio signals before sending them to the subwoofer using the audio signal circuits.
Diagnosis ProcedureINFOID:0000000001696134
1.VERIFY SUBWOOFER POWER AND GROUND SUPPLY
Check power and ground supply to the subwoofer. Refer to AV-66, "
WOOFER : Diagnosis Procedure"
Did the power and ground supply check OK?
YES >> GO TO 2
NO >> • Check connector housings for disconnected or loose terminals.
• Repair harness or connector.
2.HARNESS CHECK
1. Disconnect BOSE speaker amp. connector M112 and sub- woofer connector.
2. Check continuity between BOSE speaker amp. harness connec-
tor M112 (A) and M113 (B) and subwoofer harness connector
B72 (C).
3. Check continuity between BOSE speaker amp. harness connec-
tor M112 (A) and M113 (B) and ground.
Are the continuity test results as specified?
YES >> GO TO 3
NO >> • Check connector housings for disconnected or loose terminals.
• Repair harness or connector.
3.SUBWOOFER AMP ON SIGNAL CHECK
1. Connect BOSE speaker amp. connector M112.
2. Turn ignition switch to ACC.
3. Push “POWER” switch.
4. Check voltage between subwoofer connector B72 terminal 4 and ground.
Are the voltage test results as specified?
YES >> GO TO 4
NO >> Replace BOSE speaker amp. Refer to AV-177, "
Removal and Installation".
Connector Terminal Connector Terminal Continuity
A: M112 9
C: B72 2
Ye s
14 1
B: M113 25 4
Connector Terminal -Continuity
A: M112 9
Ground No
14
B: M113 25
ALNIA0365GB
(+)
(-) ACC
Connector Terminal
B72 4 Ground Battery voltage
ALNIA0364GB
Revision: March 2010 2008 QX56

AV-100
< COMPONENT DIAGNOSIS >[AUDIO SYSTEM]
AMP ON SIGNAL CIRCUIT
AMP ON SIGNAL CIRCUIT
DescriptionINFOID:0000000001696135
When the audio system is turned on, a voltage signal is supplied from the AV control unit to the BOSE speaker
amp. When this signal is received, the BOSE speaker amp. will turn on.
Diagnosis ProcedureINFOID:0000000001696136
1.CHECK AMP ON SIGNAL (BOSE SPEAKER AMP)
1. Turn audio system ON.
2. Check voltage between BOSE speaker amp. harness connector M113 terminal 31 and ground.
Is battery voltage present?
YES >> Inspection End.
NO >> GO TO 2
2.CHECK AMP ON SIGNAL (AV CONTROL UNIT)
Check voltage between AV control unit harness connector M42 ter-
minal 1 and ground.
Is battery voltage present?
YES >> Repair harness or connector.
NO >> Replace AV control unit. Refer to AV-164, "
Removal and
Installation".
31 - Ground
: Battery voltage
ALNIA0369GB
1 - Ground: Battery voltage
ALNIA0420GB
Revision: March 2010 2008 QX56

AV
AV CONTROL UNITAV-105
< ECU DIAGNOSIS > [AUDIO SYSTEM]
C
D
E
F
G H
I
J
K L
M B A
O P
ECU DIAGNOSIS
AV CONTROL UNIT
Reference ValueINFOID:0000000001696141
VALUES ON THE DIAGNOSIS TOOL
CONSULT-III data monitor item
TERMINAL LAYOUT
PHYSICAL VALUES
Display Item Dis-
play Vehicle status
Remarks
VHCL SPD SIG ON Vehicle speed >0 km/h (0 MPH)
Changes in indication may be delayed. This is
normal.
OFF Vehicle speed =0 km/h (0 MPH)
PKB SIG ON Parking brake is applied.
Changes in indication may be delayed. This is
normal.
OFF Parking brake is released.
ILLUM SIG ON
Block the light beam from the auto
light optical sensor when the light
SW is ON.
—
OFF Expose the auto light optical sensor
to light when the light SW is OFF or
ON.
IGN SIG ON Ignition switch ON
—
OFF Ignition switch in ACC position
REV SIG ON Selector lever in R position
Changes in indication may be delayed. This is
normal.
OFF Selector lever in any position other
than R
ALNIA0670GB
Te r m i n a l
(Wire color) Description
ConditionReference value
(Approx.)
+ – Signal nameInput/
Output
1
(GR/L) Ground Amp. ON signal
OutputIgnition
switch ON —
Battery voltage
2
(LG) 3
(V) Pre-amp. audio signal front
LH
OutputIgnition
switch ON Audio output
SKIB3609E
Revision: March 2010
2008 QX56

AV-106
< ECU DIAGNOSIS >[AUDIO SYSTEM]
AV CONTROL UNIT
4
(L) 5
(B/W) Pre-amp. audio signal rear
LH
OutputIgnition
switch ON Audio output
6
(Y) 15 Steering switch signal A Input Ignition
switch
ON Pressing switch
0V
Pressing switch 0.75
Pressing VOL up switch 2V
Except for above 5V
7
(V) Ground ACC power supply
InputIgnition
switch ACC −
Battery voltage
9
(R/L) Ground Illumination signal
Input OFFLighting switch is OFF
0V
Lighting switch is ON Battery voltage
10 — Shield — —— —
11
(BR) 12
(B/R) Pre-amp. audio signal front
RH
OutputIgnition
switch ON Audio output
13
(W) 14
(B) Audio signal rear RH Output Ignition
switch
ON Audio output
15 Ground Steering switch signal
ground —Ignition
switch
ON —0
V
16
(G) 15 Steering switch signal B Input Ignition
switch ON Pressing switch
0V
Pressing switch 0.75V
Pressing VOL down switch 2V
Except for above 5V
19
(Y) Ground Battery power supply Input Ignition
switch OFF —
Battery voltage
20
(B) Ground Ground
—Ignition
switch
ON —0
V
Terminal
(Wire color) Description
ConditionReference value
(Approx.)
+ – Signal nameInput/
Output
SKIB3609E
SKIB3609E
SKIB3609E
Revision: March 2010 2008 QX56

AV
AV CONTROL UNITAV-109
< ECU DIAGNOSIS > [AUDIO SYSTEM]
C
D
E
F
G H
I
J
K L
M B A
O P47
(W) 48
(R) AUX jack audio signal LH Input Ignition
switch ON When AUX mode is select-
ed
58
(O/L) 42
(W) Headphone LH audio sig-
nal
OutputIgnition
switch ON When DVD player is oper-
ating
59
(W/L) 43
(O) Headphone RH audio sig-
nal
OutputIgnition
switch ON When DVD player is oper-
ating
60 — Shield — —— —
62
(B) Ground A/C and AV switch assem-
bly ground —Ignition
switch ON —0
V
63
(B) 48
(R) AUX jack audio signal RH Input Ignition
switch ON When AUX mode is select-
ed
66
(Y) Ground Battery power supply Input Ignition
switch OFF —
Battery voltage
68
(Y) Ground Battery power supply Input Ignition
switch OFF —
Battery voltage
69
(V) Ground ACC power supply
InputIgnition
switch
ACC —
Battery voltage
70
(R/W) Ground MIC power
OutputIgnition
switch ON —5
V
72
(B) 71
(R/L) MIC signal
InputIgnition
switch
ON ——
Te r m i n a l
(Wire color) Description
ConditionReference value
(Approx.)
+ – Signal nameInput/
Output
SKIB3609E
SKIB3609E
SKIB3609E
SKIB3609E
Revision: March 2010 2008 QX56

AV-110
< ECU DIAGNOSIS >[AUDIO SYSTEM]
AV CONTROL UNIT
79
(G/R) Ground IGN ON or START power
supply InputIgnition
switch ON or
START —
Battery voltage
80
(GR/R) Ground Parking brake signal Input Ignition
switch ON Parking brake ON
0V
Parking brake OFF Battery voltage
81
(G/W) Ground Reverse signal
InputIgnition
switch ON R position
Battery voltage
Other than R position 0V
82
(W/R) Ground Vehicle speed signal (8-
pulse) InputIgnition
switch ON When vehicle speed is ap-
prox. 40 km/h (25MPH)
84
(BR) —
Rear view camera control
signal Input —
— —
92
(W/L) —AV communication signal 2
(H) Input/
Output ——
—
93
(P/B) —AV communication signal 2
(L) Input/
Output ——
—
94
(W/L) —
AV communication signal 1
(H) Input/
Output ——
—
95
(P/B) —
AV communication signal 1
(L) Input/
Output ——
—
96
(L) —CAN–H Input/
Output ——
—
97
(P) —CAN–L Input/
Output ——
—
121 Ground Antenna amp. ON signal Output Ignition
switch ACC —
Battery voltage
122 — Amplified window antenna
signal
Input —
— —
123 — GPS antenna signal — —— —
124 — Shield — —— —
125 — Satellite antenna signal Input Ignition
switch AC C ——
Te
rmi

nal
(Wire color) Description
ConditionReference value
(Approx.)
+ – Signal nameInput/
Output
SKIA6649J
Revision: March 2010 2008 QX56

AV
BOSE SPEAKER AMPAV-145
< ECU DIAGNOSIS > [AUDIO SYSTEM]
C
D
E
F
G H
I
J
K L
M B A
O P8
(W/B) 13
(L/B) Audio signal front door
speaker and tweeter RH
OutputIgnition
switch ON Audio output
9
(W) 14
(B) Audio signal subwoofer Output Ignition
switch ON Audio output
11
(Y) Ground Battery power supply Input Ignition
switch
OFF — Battery voltage
12
(B) Ground Ground
—Ignition
switch ON —0
V
15
(V) 28
(R) Audio signal center speak-
er
OutputIgnition
switch ON Audio output
18
(LG) 32
(V) Audio signal front LH Input Ignition
switch
ON Audio input
19
(B/R) 20
(B/R) Audio signal front RH Input Ignition
switch ON Audio input
21
(L) 22
(B/W) Audio signal rear LH Input Ignition
switch ON Audio input
Te r m i n a l
(Wire color) Description
ConditionReference value
(Approx.)
+ – Signal nameInput/
Output
SKIB3609E
SKIB3609E
SKIB3609E
SKIB3609E
SKIB3609E
SKIB3609E
Revision: March 2010 2008 QX56