2008 INFINITI QX56 air condition

B2126 DETENT SWADP-41
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
1. Turn ignition switch OFF.
2. Disconnect driver seat control unit and A/T shift selector.
3. Check continuity between driver seat control unit harness con- nector (A) and A/T shift selector harness connector (B).
4. Check continuity between driver seat control unit harness con- nector (A) and ground.
Is the inspection result normal?
YES >> GO TO 4
NO >> Repair or replace harness.
4. CHECK PARK POSITION SWITCH
Check continuity between A/T shift selector (park position switch)
terminals as follows.
Is the inspection result normal?
YES >> GO TO 5
NO >> Replace A/T shift selector. Refer to TM-195, "
A/T Shift
Selector Removal and Installation".
5. CHECK INTERMITTENT INCIDENT
Refer to GI-38, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace driver seat control unit.
NO >> Repair or replace the malfunctioning part.
AB Continuity
Connector Terminal Connector Terminal
B202 21 M203 6Yes
A —Contin u it y
Connector Terminal
B202 21 Ground No
ALJIA0194ZZ
TerminalsConditionContinuity
56 P position
Yes
Other than P position No
ALJIA0551ZZ
Revision: March 2010 2008 QX56

ADP-44
< COMPONENT DIAGNOSIS >
POWER SUPPLY AND GROUND CIRCUIT
POWER SUPPLY AND GROUND CIRCUIT
BCM
BCM : Diagnosis ProcedureINFOID:0000000001735461
Refer to BCS-32, "Diagnosis Procedure".
BCM : Special Repair RequirementINFOID:0000000001735462
1. REQUIRED WORK WHEN REPLACING BCM
Initialize control unit. Refer to CONSULT-III Operation Manual.
>> Work end.
DRIVER SEAT CONTROL UNIT
DRIVER SEAT CONTROL UN IT : Diagnosis ProcedureINFOID:0000000001735463
NOTE:
Do not disconnect the battery negative terminal and the driver seat control unit connector until DTC is con-
firmed with CONSULT-III.
1. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Check voltage between driver seat control unit harness connec- tor and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Check the following. • Repair or replace harness between driver seat control unit and fuse block (J/B).
• Circuit breaker.
2. CHECK GROUND CIRCUIT
Check continuity between the driver seat control unit harness con-
nector and ground.
Is the inspection result normal?
YES >> Driver seat control unit power supply and ground circuit are OK.
NO >> Repair or replace harness.
Te r m i n a l s
Power
source ConditionVoltage (V)
(Approx.)
(+)
(–)
Driver seat
control unit connector Te r m i n a l
B202 6
Ground START
power sup-
ply Ignition
switch
START Battery
voltage
B203 33
Battery
power sup- ply Ignition
switch OFF
40
LIIA1897E
Driver seat control unit
connector Te r m i n a l
Ground Continuity
B202 32
Ye s
B203 48
PIIA4542E
Revision: March 2010 2008 QX56

SLIDING SWITCHADP-47
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
4. Check continuity between driver seat control unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK DRIVER SEAT CONTROL UNIT OUTPUT
1. Connect the driver seat control unit.
2. Turn ignition switch ON.
3. Check voltage between driver s eat control unit harness connec-
tor and ground.
Is the inspection result normal?
YES >> GO TO 4
NO >> Replace driver seat control unit.
4. CHECK SLIDING SWITCH
Refer to ADP-47, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 5
NO >> Replace power seat switch LH.
5. CHECK INTERMITTENT INCIDENT
Refer to GI-38, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace driver seat control unit.
NO >> Repair or replace malfunctioning part.
Component InspectionINFOID:0000000001735470
1. CHECK SLIDING SWITCH
1. Turn ignition switch OFF.
2. Disconnect power seat switch LH.
3. Check continuity between power seat switch LH terminals.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace power seat switch LH.
Driver seat control unit connector Te r m i n a l
GroundContinuity
B202 11
No
26
Driver seat control unit
connector Te r m i n a l s
Voltage (V)
(Approx.)
(+) (–)
B202 11
Ground Battery voltage
26
PIIA4577E
Te r m i n a l Condition Continuity
Power seat switch LH
3 7 Sliding switch (backward)
Operate
Yes
Release No
1 Sliding switch (forward) Operate
Yes
Release No
LIIA1126E
Revision: March 2010 2008 QX56

RECLINING SWITCHADP-49
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK DRIVER SEAT CONTROL UNIT OUTPUT
1. Connect the driver seat control unit connector.
2. Turn ignition switch ON.
3. Check voltage between driver s eat control unit harness connec-
tor and ground.
Is the inspection result normal?
YES >> GO TO 4
NO >> Replace driver seat control unit.
4. CHECK RECLINING SWITCH
Refer to ADP-49, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 5
NO >> Replace power seat switch LH.
5. CHECK INTERMITTENT INCIDENT
Refer to GI-38, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace driver seat control unit.
NO >> Repair or replace the malfunctioning part.
Component InspectionINFOID:0000000001735474
1. CHECK RECLINING SWITCH
1. Turn ignition switch OFF.
2. Disconnect power seat switch LH.
3. Check continuity between power seat switch LH terminals.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace power seat switch LH.
Driver seat control unit connector Te r m i n a l
GroundContinuity
B202 12
No
27
Driver seat control
unit connector Te r m i n a l s
Voltage (V)
(Approx.)
(+) (–)
B202 12
Ground Battery voltage
27
PIIA4580E
Te r m i n a l s Condition Continuity
Power seat switch LH
3 9
Reclining switch
(backward) Operate
Yes
Release No
10 Reclining switch
(forward) Operate
Yes
Release No
LIIA1128E
Revision: March 2010 2008 QX56

LIFTING SWITCH (FRONT)ADP-51
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
4. Check continuity between driver seat control unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK DRIVER SEAT CONTROL UNIT OUTPUT
1. Connect the driver seat control unit.
2. Turn ignition switch ON.
3. Check voltage between driver s eat control unit harness connec-
tor and ground.
Is the inspection result normal?
YES >> GO TO 4
NO >> Replace driver seat control unit.
4. CHECK LIFTING SWITCH (FRONT)
Refer to ADP-51, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 5
NO >> Replace power seat switch LH.
5. CHECK INTERMITTENT INCIDENT
Refer to GI-38, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace driver seat control unit.
NO >> Repair or replace the malfunctioning part.
Component InspectionINFOID:0000000001735478
1. CHECK LIFTING SWITCH (FRONT)
1. Turn ignition switch OFF.
2. Disconnect power seat switch LH.
3. Check continuity between power seat switch LH terminals.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace power seat switch LH.
Driver seat control unit connector Terminal
GroundContinuity
B202 13
No
28
Driver seat control unit
connector Te r m i n a l s
Voltage (V)
(Approx.)
(+) (–)
B202 13
Ground Battery voltage
28
PIIA4583E
Te r m i n a l Condition Continuity
Power seat switch LH
3 5 Lifting switch front (down)
Operate
Yes
Release No
6 Lifting switch front (up) Operate
Yes
Release No
LIIA1130E
Revision: March 2010 2008 QX56

LIFTING SWITCH (REAR)ADP-53
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK DRIVER SEAT CONTROL UNIT OUTPUT
1. Connect the driver seat control unit.
2. Turn ignition switch ON.
3. Check voltage between driver s eat control unit harness connec-
tor and ground.
Is the inspection result normal?
YES >> GO TO 4
NO >> Replace driver seat control unit.
4. CHECK LIFTING SWITCH (REAR)
Refer to ADP-53, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 5
NO >> Replace power seat switch LH.
5. CHECK INTERMITTENT INCIDENT
Refer to GI-38, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace driver seat control unit.
NO >> Repair or replace the malfunctioning part.
Component InspectionINFOID:0000000001735482
1. CHECK LIFTING SWITCH (REAR)
1. Turn ignition switch OFF.
2. Disconnect power seat switch LH.
3. Check continuity between power seat switch LH terminals.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace power seat switch LH.
Driver seat control unit connector Te r m i n a l
GroundContinuity
B202 14
No
29
Driver seat control unit
connector Te r m i n a l s
Voltage (V)
(Approx.)
(+) (–)
B202 14
Ground Battery voltage
29
PIIA4586E
Te r m i n a l Condition Continuity
Power seat switch LH
3 2 Lifting switch rear (up)
Operate Yes
Release No
8 Lifting switch rear (down) Operate Yes
Release No
LIIA1132E
Revision: March 2010
2008 QX56

TILT SWITCHADP-55
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
OK or NG
OK >> GO TO 3
NG >> Repair or replace harness.
3. CHECK ADP STEERING SWITCH GROUND CIRCUIT
Check continuity between ADP steer ing switch connector M16 termi-
nal 1 and ground.
OK or NG
OK >> Check the condition of the harness and connector.
NG >> Replace or replace harness.
4. CHECK TILT SWITCH
Refer to ADP-55, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 5
NO >> Replace ADP steering switch.
5. CHECK INTERMITTENT INCIDENT
Refer to GI-38, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace automatic driv e positioner control unit.
NO >> Repair or replace the malfunctioning part.
Component InspectionINFOID:0000000001754042
1. CHECK ADP STEERING WHEEL TILT SWITCH
Check continuity between ADP steer ing switch terminals as follows.
OK or NG
OK >> INSPECTION END
NG >> Replace ADP steering switch. 1 - Ground : Continuity should not exist.
17 - Ground : Continuity should not exist.
1 - Ground : Continuity should exist.
LIIA0490E
Terminals
ConditionContinuity
2 1ADP steering switch ON (UP operation) Yes
Other than above
No
3 ADP steering switch ON (DOWN operation) Yes
Other than above
No
LIIA1435E
Revision: March 2010 2008 QX56

ADP-58
< COMPONENT DIAGNOSIS >
PEDAL ADJUSTING SWITCH
Refer to GI-38, "Intermittent Incident".
Is the inspection result normal?
YES >> Replace automatic drive positioner control unit.
NO >> Repair or replace the malfunctioning part.
Component InspectionINFOID:0000000001735486
1.CHECK PEDAL ADJUSTING SWITCH
1. Turn ignition switch OFF.
2. Disconnect pedal adjusting switch.
3. Check continuity between pedal adjusting switch terminals.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace pedal adjusting switch.
Te r m i n a l ConditionContinuity
Pedal adjusting switch
1 2
Pedal adjusting switch
(forward) Operate
Yes
Release No
3 Pedal adjusting switch
(backward) Operate
Yes
Release No
LIIA1014E
Revision: March 2010 2008 QX56